JUNG DAW360 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JUNG DAW360 (8 Seiten) in der Kategorie Schalten. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/8
Ceiling automatic switch
Light Management
Ceiling automatic switch
Art.-No.: DAW 360 WW
Ceiling automatic switch
Art.-No.: DAW 360 AL
Operating instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
Danger of electric shock. Always disconnect before carrying out work on the devise or
load. At the same time, take into account all circuit breakers that supply dangerous
voltage to the device or load.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
The load is not electrically isolated from the mains even when the device is switched off.
Do not press on the sensor window. Device can be damaged.
The device is not suitable for use as a burglar alarm or other alarm.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1
(1) Flush-mounted insert
(2) Motion detector cover
(3) Adjuster sens
(4) Adjuster time
(5) Adjuster lux
(6) Brightness sensor
(7) LED display, behind the lens
(8) Lens
(9) Decor ring
(10) Push-on cover
1/8
82563813
J:0082563813 17.11.2011
3 Function
Intended use
- Automatic switching of lighting depending on the heat motion and ambient brightness.
- Operation with concealed insert for dimming, switching or extension insert, 3-wire
- Ceiling installation on flush-mounted insert
Product characteristics
- Run-on time, sensitivity and brightness threshold settable
- Test operation for checking the detection area
- Short-time operation to control signal encoders
- Dimming phase in combination with dimming insert
- Saving a switch-on brightness with dimming inserts
- Dimming lights with dimming inserts
- Manual switch-on possible via extension insert, 2-wire, or installation button
- 78 lens segments in 5 recording levels
- Extension of the detection area in combination with the 3-wire extension insert
- Detection area can be limited using push-on cover
Automatic operation
The controller detects heat motions of people, animals and objects.
- The light is switched on if a person enters the monitored detection area and the brightness
is below the set threshold.
- The light is switched off if no more movement is detected in the detection area and the
follow-up time has elapsed.
Dimming phase with dimming insert
If the motion detector cover is fitted on a dimming insert, then when the run-on time elapses the
lighting is dimmed to minimum brightness and then switched off. The time from the start of
dimming to switching-off is always approx. 30 s. If a motion is detected during the dimming
phase, the motion detector switches the lighting to the stored switch-on brightness again.
Behaviour in case of a mains failure
- Less than 0.2 seconds: the old switching position is restored after mains return.
- 0.2 seconds to approx. 2 seconds: when the power returns, the lighting is switched on
again for the run-on time. Each detected movement restarts the run-on time again.
- Longer than 2 seconds: when the power returns, the motion detector carries out a brief
calibration process. Then the lighting remains switched on for the run-on time. Each
detected movement restarts the run-on time again.
LED display (7)
Main device Extension
LED lights up during the calibration process. LED lights up during the calibration process.
LED lights up when a motion is detected if the
lighting is switched off and the brightness is
not below the brightness threshold.
LED lights up when a motion is detected.
4 Operation
Switching on the light
A 2-wire extension or an installation button, NO contact is connected.
o Press extension or installation button.
Light is switched on independently of the brightness, with a dimming insert to switch-on
brightness. Automatic mode is active.
i After manual switch-on the run-on time is at least 2 minutes.
i Manual switch-on is not possible.
2/8
82563813
J:0082563813 17.11.2011
Light Management
Ceiling automatic switch
Dimming light with dimming insert
The light can be dimmed using a 2-wire extension. The light remains at the dimmed value until
the run-on time has elapsed.
o Press 2-wire insert at top or bottom until the desired brightness is reached.
i An installation button cannot be used for dimming.
Saving a switch-on brightness with dimming insert
A 2-wire extension can be used to save any desired switch-on brightness. In the state as
supplied the switch-on brightness is set to maximum.
The saved switch-on brightness is retained in the event of a power failure.
o Set the required brightness.
o Press 2-wire extension for longer than 3 seconds over entire surface.
Switch-on brightness is saved. For confirmation the lighting switches off briefly and then on
again to the saved switch-on brightness.
5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before carrying out work on the device or load, disengage all the
corresponding circuit breakers. Cover up live parts in the working environment.
Selecting the installation location
Figure 2: Sensor window and detection area
The motion detector has a detection area of 360° (figure 2). The diameter of the detection area
depends on the installation height and the direction of motions of persons in the detection area
(figure 3). At an installation height of 3 m the maximum diameter on the floor is approx. 12 to 20
m.
3/8
82563813
J:0082563813 17.11.2011
Light Management
Ceiling automatic switch
Produktspezifikationen
| Marke: | JUNG |
| Kategorie: | Schalten |
| Modell: | DAW360 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit JUNG DAW360 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Schalten JUNG
20 September 2024
3 September 2024
2 September 2024
1 September 2024
28 August 2024
28 August 2024
28 August 2024
23 August 2024
23 August 2024
13 August 2024
Bedienungsanleitung Schalten
- Schalten Asus
- Schalten Belkin
- Schalten Hama
- Schalten HP
- Schalten LogiLink
- Schalten Manhattan
- Schalten Nedis
- Schalten Philips
- Schalten SilverCrest
- Schalten Panasonic
- Schalten Brennenstuhl
- Schalten Clas Ohlson
- Schalten Cotech
- Schalten Profile
- Schalten ZyXEL
- Schalten Bosch
- Schalten Yamaha
- Schalten Powerfix
- Schalten CSL
- Schalten Eminent
- Schalten Linksys
- Schalten Netgear
- Schalten König
- Schalten PCE
- Schalten Renkforce
- Schalten Trotec
- Schalten Schneider
- Schalten Rex
- Schalten Kaiser
- Schalten Vivanco
- Schalten Abus
- Schalten Elro
- Schalten Smartwares
- Schalten Tesla
- Schalten Perel
- Schalten Nexa
- Schalten Tork
- Schalten GEV
- Schalten Goobay
- Schalten Lindy
- Schalten Tripp Lite
- Schalten Ansmann
- Schalten Mercusys
- Schalten Marmitek
- Schalten Honeywell
- Schalten TRENDnet
- Schalten TP-Link
- Schalten Kathrein
- Schalten Flamingo
- Schalten Alcatel
- Schalten Tiptel
- Schalten Black Box
- Schalten Alpine
- Schalten Techly
- Schalten Ebode
- Schalten Theben
- Schalten Vacmaster
- Schalten GAO
- Schalten Hager
- Schalten Behringer
- Schalten Omnitronic
- Schalten Monoprice
- Schalten Ecler
- Schalten Monacor
- Schalten Huawei
- Schalten Victron Energy
- Schalten Ei Electronics
- Schalten Edimax
- Schalten Totolink
- Schalten D-Link
- Schalten Sylvania
- Schalten Audiovox
- Schalten B-Tech
- Schalten QNAP
- Schalten SPC
- Schalten Speaka
- Schalten Digitus
- Schalten Sygonix
- Schalten DataVideo
- Schalten Lancom
- Schalten LevelOne
- Schalten Merten
- Schalten APC
- Schalten Eberle
- Schalten Cisco
- Schalten Delta Dore
- Schalten Grässlin
- Schalten Tenda
- Schalten CyberPower
- Schalten Boss
- Schalten IFM
- Schalten Intertechno
- Schalten Elation
- Schalten Ubiquiti Networks
- Schalten Kramer
- Schalten Aeon Labs
- Schalten Intellinet
- Schalten Eaton
- Schalten AV:link
- Schalten Hikvision
- Schalten Vemer
- Schalten PreSonus
- Schalten Planet
- Schalten EnGenius
- Schalten Finder
- Schalten Mikrotik
- Schalten Shimano
- Schalten Homematic IP
- Schalten Berker
- Schalten Dormakaba
- Schalten Emerson
- Schalten Generac
- Schalten Intermatic
- Schalten KlikaanKlikuit
- Schalten Mercury
- Schalten Paladin
- Schalten Provision ISR
- Schalten Robbe
- Schalten SEC24
- Schalten Steren
- Schalten Suevia
- Schalten AMX
- Schalten Triax
- Schalten WHALE
- Schalten Vimar
- Schalten Cudy
- Schalten Siig
- Schalten Electro Harmonix
- Schalten RGBlink
- Schalten Iogear
- Schalten StarTech.com
- Schalten Smart-AVI
- Schalten Dahua Technology
- Schalten PAC
- Schalten Gefen
- Schalten Avocent
- Schalten Legrand
- Schalten Atlantis Land
- Schalten CYP
- Schalten H-Tronic
- Schalten ATen
- Schalten Axing
- Schalten KanexPro
- Schalten SmartAVI
- Schalten Advantech
- Schalten Kraus & Naimer
- Schalten Chacon
- Schalten Juniper
- Schalten Fibaro
- Schalten Phoenix Contact
- Schalten Audac
- Schalten OSD Audio
- Schalten Wentronic
- Schalten SunBriteTV
- Schalten BZBGear
- Schalten Crestron
- Schalten Kemo
- Schalten ORNO
- Schalten Extron
- Schalten Atlona
- Schalten Equip
- Schalten Heitronic
- Schalten Hamlet
- Schalten STI
- Schalten Matrox
- Schalten Blustream
- Schalten Vivolink
- Schalten Mach Power
- Schalten Ernitec
- Schalten Cambium Networks
- Schalten ConnectPro
- Schalten Micro Connect
- Schalten Intelix
- Schalten ICasa
- Schalten Maclean Energy
- Schalten Cooking Performance Group
- Schalten Flic
- Schalten Liberty
- Schalten Noark
- Schalten 2USB
- Schalten KVM-TEC
- Schalten Setti+
- Schalten PureLink
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
12 Oktober 2024
11 Oktober 2024
8 Oktober 2024
8 Oktober 2024
5 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
3 Oktober 2024