JUNG BTCLS928 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JUNG BTCLS928 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 31 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Safety instructions
Electrical equipment must only be installed and assembled by qualied electricians. Failure to comply with these instructions may result in damage to the device,
re or other hazards. This product is only intended for use in dry rooms.
These instructions are an integral part of the product and must remain with the end customer.
DANGER!
Electrical shock when live parts are touched. An electric shock can be fatal.
Operation
The lower half of the cover is used for operation. All operations are made via 8 sensor buttons. In standby mode the buttons are hidden and are displayed each
time you touch the lower area.
Switching on / Switching o
The Bluetooth Connect is switched on and o here (standby).
Note: After switching on, the Bluetooth Connect connects automatically to the last audio source if it can be reached. If the source is not available, e.g. because it is
not within range, the next audio source is connected. The Bluetooth Connect attempts to reach the taught-in audio sources in the sequence they were taught in.
While searching for the connection, the button illumination dims brighter and darker. The playback starts automatically depending on the device type / device
software.
Adjusting the volume
The volume is adjusted using the buttons. The Bluetooth Connect always starts with the volume that was last adjusted.
Teaching in the audio source
With a press of a button, the Bluetooth Connect switches to the learn mode and is then visible for a maximum of 30 seconds for audio players with an integrated
Bluetooth interface (e.g. smartphone or MP3 player). A connection can now be established via such a device and it can be taught in on the Bluetooth Connect.
Note: During the 30 seconds, the buttons will ash until the connection has been established.
In some operating systems, a device that has previously been taught-in can only be taught-in again if the existing connection was deleted in this device.
Selecting the audio source
With a long press of a button (> 2 s) the connection to the next taught-in and accessible audio source is established. Afterwards, the playback is started.
The search is indicated by dimming the button illumination brighter and darker. This procedure can last up to 40 seconds depending on the number of the taught-in
devices.
Selecting a track
The last/next track can be selected by a brief press of a button. The track sequence corresponds to the order of the audio source.
The sequence can normally be dened there according to albums, artists, genre or playlists.
Operating instructions
Description of device
The JUNG Bluetooth Connect BTC… consists of an operating cover and a ush-mounted power supply.
The audio source (e.g. smartphone or MP3 player) is connected and the device is operated via the operating cover.
The device is operated and set up via 8 sensor buttons.
The connections for mains voltage, loudspeakers and audio output are available on the power supply unit.
The Bluetooth Connect can be operated with one or two loudspeaker modules LSM….
The music signal is transmitted via Bluetooth, amplied internally and output to loudspeakers or an external amplier.
The tracks and volume can be changed via sensor buttons. Up to 6 audio sources can be taught in, from which one
audio source can be connected actively with the Bluetooth Connect.
en_0024074100_BTC_V2_web 1 - 4 20.04.15
Bluetooth Connect
BTC…
Pause
With a press of a button, the playback of the connected audio source is interrupted.
Deleting connections
With a long press of a button (> 10 s), all previously taught-in audio sources are deleted from the Bluetooth Connect.
Intended use
• Installation in a ush-mounted device box according to DIN EN 49073 (recommended: deep box)
• Bluetooth Connect for audio output in conjunction with a playback device and for media control
Product characteristics
Bluetooth Connect with sensor buttons
• Solid glass front
• Stereo playback
• Connecting terminals for two loudspeakers
• Stereo/mono change-over
• Easy operation
• High reception quality
• Integrated amplier
• Storage of 6 audio sources
Switching on with the last audio source
Switching on with the last volume
• Extension unit input
Installation
Netzanschluss
L N
en_0024074100_BTC_V2_web 2 - 4 20.04.15
Bluetooth Connect
BTC…
The Bluetooth Connect BTC... has been designed for installation in device boxes DIN EN 49073.
The connections for mains voltage, loudspeakers and the audio output are located on the ush-mounted
power supply unit. The operating cover together with the frame are mounted onto the power supply unit.
Before carrying out work on the device, disengage all the corresponding circuit
breakers. Cover up live parts in the working environment. Within the device
box, all the cables carrying low voltages must have an insulating hose in order
to guarantee protective separation.
The Bluetooth Connect requires a permanent mains connection.
A loopthrough via the connecting terminals is not permitted.
Connecting an extension unit
L N
Connecting a loudspeaker
L N
L R
Mono/Stereo change-over
If two loudspeakers are to be operated in mono, e.g. in separate rooms, it is possible to change over by pressing both buttons simultaneously for 10 seconds. The
new mode is indicated by tones. One tone corresponds to the mono mode, and two tones correspond to the stereo mode.
Line-out (AUX)
The Line-out (AUX) is used for connecting to an external amplier or to the JUNG Smart Radio RAD....
Installing the power supply unit
After connecting all cables, the power supply unit must be mounted in the device box in the correct position.
Installing the operating cover
After installing the power supply unit in the device box, the cover incl. the frame is mounted onto the power supply unit.
en_0024074100_BTC_V2_web 3 - 4 20.04.15
Bluetooth Connect
BTC…
The extension unit connection (1) is used to switch the Bluetooth Connect on/o via switches, e.g. together
with the light. The extension unit input may only be operated on the same phase.
The device is intended for operation with one or two loudspeaker modules LSM… . The connection cable
can be up to 5 m long.
In stereo mode, both outputs (L+R) are used. The device detects autonomously if only one loudspeaker is
used and then changes its operating mode to mono.
The connection of several loudspeakers per output is not permitted.
Loudspeakers of other manufacturers may only be used if the technical data is identical with the JUNG
LSM… .
Please observe the polarity.
Before carrying out work on the device, disengage all the corresponding circuit
breakers. Cover up live parts in the working environment. Within the device
box, all the cables carrying low voltages must have an insulating hose in order
to guarantee protective separation.


Produktspezifikationen

Marke: JUNG
Kategorie: Nicht kategorisiert
Modell: BTCLS928

Brauchst du Hilfe?

Wenn Sie Hilfe mit JUNG BTCLS928 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert JUNG

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-