JUNG AS1561.07FKO Bedienungsanleitung

JUNG Nicht kategorisiert AS1561.07FKO

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JUNG AS1561.07FKO (7 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/7
Light Management Radio-control pushbutton and pilot lamp
Ref.-no.: ..1561.07FKO..
Operating Instructions
Radio-control pushbutton and pilot lamp
1. Function
The radio-contol pushbutton permits radio-controlled or manual switching
and dimming of lamps.The starting brightness can be stored in the device
as memory brightness. The pushbutton with radio-control receiver is
plugged onto one of the following inserts:
 Universal touch dimmer 1254 UDE
 Standard touch dimmer 1225 SDE
 Relay insert single-channel 1201 URE
 Relay insert two-channel 1202 URE
 Tronic switching insert 1254 TSE
 LV triac switching insert 1244 NVSE
 Touch control unit 1240 STE
Relay insert with potential-free contact 1201-1 URE After reception of a
data telegram from a programmed radio-control detector and
corresponding darkness, the radio-contol pushbutton is switched on for
about 1 minute with the preset memory brightness. The radio-contol
pushbutton can be programmed to identify up to 30 radio channels.
Lightscapes
The radio-contol pushbutton can be included in up to five lightscapes
which are activated with the corresponding radio-control transmitters (e.g.
hand-held transmitter ‘Komfort’) and stored. The desired lightscape key
must be programmed beforehand into the radio-contol pushbutton.
All-ON / All-OFF
The programming of a radio channel (e.g. hand-held transmitter
‘Komfort’) always includes the simultaneous and automatic storage of the
functions of the All-ON or All-OFF key.The All-ON or All- OFF key of a
radio-control transmitter switches the load connected to the switching
actuator on or off.
Light control
In combination with a programmed radio-control presence detector, the
radio-contol pushbutton can be used for lighting control functions. For
more information, refer to the operating instructions of the radio presence
detector.
Stand: Mai-07 325 276 53
Light Management Radio-control pushbutton and pilot lamp
Ref.-no.: ..1561.07FKO..
Important
The present instructions describe the functions of the radio-control
pushbutton without lighting control. More information on light control with
a presence detector is set out in the operating instructions for these
devices.
WARNING!
Caution: The installation and assembly of electrical equipment may
only be performed by a skilled electrician.
2. Fitting
The radio-control pushbutton can only be operated in conjunction with the
inserts listed under ‘Functions’. Connection and fitting are described in
the operating instructions of the insert.
Procedure
1. Install the selected insert (1) in a flush-mounting box (deep model
recommended), the connecting terminals of the insert pointing
downwards.
2. Plug the radio-control pushbutton (2) together with frame (3) onto
the insert while the mains voltage is disconnected.
c
d
e
L The distance from electrical appliances (e.g. microwave oven, hi-fi and
TV sets) must be at least 0.5 m.
L To prevent saturation of the radio receiver (actuator), the radiocontrol
pushbutton must be at least 1 m away from the nearest transmitter.
Learning a Radio Transmitter
During programming of a transmitter, the sensitivity of a radiocontrol
receiver is reduced to a range of approx. 5 m. The distance between the
radio-control pushbutton and the transmitter to be programmed should be
between 0.5 m and 5 m.
Procedure
1. Switch off the load connected to the radio-control pushbutton by a brief
depression (< 0,4 s) of any of the two pushbutton rockers.
2. Depress both rockers of the radio-control pushbutton at the same time
for abt. 4 seconds (fig. B: double-sided operation) to switch over to the
programming mode. The LED blinks for abt. 1 min (Fig. C). The radio
pushbutton is then in the programming mode.
2
Light Management Radio-control pushbutton and pilot lamp
Ref.-no.: ..1561.07FKO..
> 4 s
Prog
1 min t
3. Send a radio telegram from the selected transmitter (fig. D); see
„Radio-control transmitter“ operating instructions:
ABC
123
45
1
2
3
4
5
6
7
8
<
>>
<
Programming a channel
Depress the channel key for more than 1 second.
Programming a lightscape key
Depress the lightscape key for more than 3 seconds.
Programming a detector
Remove the battery for about 2 minutes from the detector. Put the the
battery back in place and make a movement inside the detection range of
the detector within the next 10 minutes.
Programming a presence detector
Remove the battery(ies) for about 2 minutes from the transmitter. After
putting the battery back in place, the device starts transmitting
programming telegrams for about 30 s.
L It is not possible to program a combination consisting of presence-
control detector and detector.
4. The radio pushbutton confirms the storage by switching on the
LED permanently
Prog
1 min t
5. The programming mode ends automatically after about 1 minute or
can be terminated by a short depression of the programming key. The
radio-control pushbutton is then again in the normal operating mode.
L When all 30 memories are occupied, it is necessary to delete an
already stored transmitter before a new one can be programmed.
3


Produktspezifikationen

Marke: JUNG
Kategorie: Nicht kategorisiert
Modell: AS1561.07FKO

Brauchst du Hilfe?

Wenn Sie Hilfe mit JUNG AS1561.07FKO benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert JUNG

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-