JUNG A1180WU Bedienungsanleitung

JUNG Schalter A1180WU

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JUNG A1180WU (14 Seiten) in der Kategorie Schalter. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/14

Automatic switch 180° 1.10 m

Light Management

Standard automatic switch 180° 1.10 m

Art.-No.: ..1180..

Universal automatic switch 180° 1.10 m

Art.-No.: ..1180-1..

Operationsmanual

1 Safety instructions

Electrical equipment may only be installed and fitted by electrically skilled persons.

Failure to observe the instructions may cause damage to the device and result in fire and

other hazards.

Danger of electric shock. Always disconnect before carrying out work on the devise or

load. At the same time, take into account all circuit breakers that supply dangerous

voltage to the device or load.

Danger of electric shock. Device is not suitable for disconnection from supply voltage.

The load is not electrically isolated from the mains even when the device is switched off.

Do not press on the sensor window. Device can be damaged.

The device is not suitable for use as a burglar alarm or other alarm.

These instructions are an integral part of the product, and must remain with the end

customer.

2 Device components

picture 1

(1) Flush-mounted insert

(2) Frame

(3) Motion detector cover

(4) Cover plate / slide switch

1/14

32540233

J:0082540233 26.07.2010

Automatic switch standard

picture 2: Automatic switch standard

Automatic switch universal

picture 3: Automatic switch universal

(5) Adjuster, sensitivity

(6) Adjuster, brightness

(7) Operating mode switch

(8) Adjuster, run-on time

3 Function

Intended use

- Automatic switching of lighting depending on the heat motion and ambient brightness.

- Operation with concealed insert for dimming, switching or extension insert, 3-wire

- Interior mounting on flush-mounted insert at a height of 1.1 m.

2/14

32540233

J:0082540233 26.07.2010

Light Management

Automatic switch 180° 1.10 m

Product characteristics

Automatic switch standard

- Sensitivity and brightness threshold settable

- Manual switch-on possible via extension insert, 2-wire, or installation button

- 18 lens segments in 2 recording levels

- Extension of the detection area in combination with the 3-wire extension insert

- Detection area can be limited using cover plate

i Dimming inserts can only execute switching functions.

Automatic switch universal

- Run-on time, sensitivity and brightness threshold settable

- Teach function to save the current brightness as the new brightness threshold.

- Operating mode switch for Automatic operation, Continuous on or Continuous off

- Short-time operation, e.g. to control acoustic signal encoders

- Manual switch-on possible via extension insert, 2-wire, or installation button

- With the dimmer insert, it is possible to change the brightness using a 2-wire extension

insert

- Switch-on brightness can be saved with the dimmer insert

- With the dimmer insert, the dim-down function is possible at the end of the run-on time

- 18 lens segments in 2 recording levels

- Extension of the detection area in combination with the 3-wire extension insert

- Detection area can be limited using cover plate

- High protection against ambient light

Automatic operation

The controller detects heat motions of people, animals and objects.

- The light is switched on if a person enters the monitored detection area and the brightness

is below the set threshold.

Each detected movement restarts the run-on time.

- The light is switched off if no more movement is detected in the detection area and the run-

on time has elapsed.

Light oscillations e.g. due to the cooling of bulbs are prevented via interlock times in the

automatic switch. No switching commands are performed during the interlock.

Automatic switch standard approx. 3 seconds

Automatic switch universal: 0.2 to 3 seconds, dynamic.

Automatic switch universal: The day/night and night/day switch-over is performed only after the

brightness is above or below the threshold for approx. 10 seconds. This prevents the motion

detector from switching to Night mode is there is brief shadow or to Day mode if there is brief

light.

Behaviour in case of mains failure for automatic switch standard

- Less than 0.2 seconds: the old switching position is restored after mains return.

- 0.2 seconds to approx. 1 seconds: when the power returns, the lighting is switched on

again for the run-on time.

- Longer than 1 second: when the power returns, the motion detector carries out a self test

for approx. 60 seconds. The lighting is switched on during the self test. Then the lighting

switches off for the length of the run-on time.

Behaviour in case of mains failure for automatic switch universal

- Less than 0.2 seconds: the old switching position is restored after mains return.

- 0.2 seconds to approx. 2 seconds: when the power returns, the lighting is switched on

again for the run-on time.

- Longer than 2 seconds: when the power returns, the motion detector carries out a self test

for approx. 90 seconds. The lighting is switched on during the self test. Then the lighting

switches off briefly, and then on again for the length of the run-on time.

i In the Continuous on and Continuous off operating modes, the light is switched on or off

after the self-test.

i A power failure of longer than 2 seconds causes the loss of the switch-on brightness and

the brightness threshold saved via the Teach function.

3/14

32540233

J:0082540233 26.07.2010

Light Management

Automatic switch 180° 1.10 m

Produktspezifikationen

Marke:	JUNG
Kategorie:	Schalter
Modell:	A1180WU
Breite:	- mm
Tiefe:	- mm
Produktfarbe:	Beige
Internationale Schutzart (IP-Code):	IP44
Steuerung:	Sensor
Höhe:	- mm
Menge pro Packung:	1 Stück(e)