JL Audio Stealthbox SB-T-TUNCNSL2/10W3v3 Bedienungsanleitung

JL Audio Nicht kategorisiert Stealthbox SB-T-TUNCNSL2/10W3v3

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JL Audio Stealthbox SB-T-TUNCNSL2/10W3v3 (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 29 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
Stealthbox®
I N S T A L L A T I O N G U I D E
SB- T- T U N C N S L 2 / 1 0 W 3 v 2 , J L AU D I O , I n c 2 0 0 5 Sh e e t S K U # 0 1 1 1 8 0 R e v i s i o n 4 / 6 / 2 0 0 5Pag e 1
for the
SB-T-TUNCNSL2/10W3v2
(‘03-Up Toyota Tundra Access & Double Cab
with front bucket seats and center console)
This Stealthbox is a product which
requires professional installation skills and
tools.
Please read this installation guide thor-
oughly before beginning the project. It
will guide you step by step through the
installation. Several of the steps in this
process may require two people to
accomplish.
It is absolutely vital that the enclosure
be properly mounted to the vehicle
according to these instructions. Failure
to mount the enclosure properly pres-
ents two problems: 1) The sub-bass
performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and
2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.
Please enjoy your JL Audio Stealthbox
responsibly.
STEP 1:
Using a 14mm socket, remove the
four bolts that secure the passenger side front
seat.
STEP 2:
Tilt the seat to the rear, unplug the
exposed wire assembly, remove the seat from
the truck.
STEP 3:
Remove the front storage access
door. Using a 10mm socket, remove the
exposed bolts.
STEP 4:
With the main storage door open,
grab ahold of the black cup holder section
and pull up.
STEP 5:
Using a 10mm socket, remove the
exposed bolts. Also remove the bolts that are
located at the bottom of the main storage
bucket.
STEP 6:
Remove the plastic buttons that are
located on each side of the center console.
START
HERE
Continued on Next Page
w w w . j l a u d i o . c o m
➔ ➔
➔➔➔
STEP 7: Slide the center console to the rear of
truck.This will allow exposer of the 12v plug wires.
Unplug and then remove the center console from
truck.
*Tundra Access Cab Only*
Keep the air ducts inside the truck, for now.
STEP 11: Back inside the truck. Remove the black
bracket that is mounted to the floor of the
truck(not pictured).
*Tundra Access Cab Only*
Using a 1/2” drill bit and drill. Enlarging the mounting
holes from the bracket.
Cont.
From
Previous
Page
Continued on Next Page
STEP 8: *Tundra Access Cab Only*
With the center console out of the truck, flip up
side down. Remove the two air duct ears that are
located to the rear of the center console.
*Tundra Access Cab Only*
STEP 12: Cut 1-1/2” off of each carpet flap, that is
located in front of the mounting holes, from
STEP10.
*Tundra Access Cab Only*
STEP 13(a): Place only one of the supplied wax
squares into this location.
Place the middle of the supplied wax square, 4-3/4”
back from the front consoles metal mounting brack-
et.
*Tundra Double Cab Only*
STEP 13(b)
FRONT WAX SQUARE
Place the middle of one of the supplied wax
squares, 4-3/4” back from the front consoles metal
mounting bracket.
REAR WAX SQUARES
Place the middle of the remaining pair of supplied
wax squares, 1-3/4” back from the center console
rear mounting holes.
STEP 9: Remove the 8 screws that is securing
the black plastic support to the outer console. Not
all circles represent all 8 screws.
There are a pair of screws on each side of the con-
sole that need to be removed.
STEP 10: *Tundra Access Cab Only*
Now it is time to remove those air ducts from
STEP 7. With the ducts removed, you will need to
cut both ducts. Place the ducts so the front of the
ducts are facing to the right.
Driver’s side: Measure and mark 3/4” from front
of foam tape, back. Cut at location.
Passenger’s side: Cut at the middle of the foam
tape.
SB-T- T UN C N SL2 / 1 0 W 3 v2 , JL AU D I O, I n c 2 0 05 She e t S K U # 01 1 1 8 0 R e vis i o n 4 /6 / 20 0 5Pag e 2
w w w . j l a u d i o . c o m
Passenger’s side
middle
Drivers side
3/4”
4-3/4” 6-1/2
1-3/4”
Cont.
From
Previous
Page
Continued on Next Page
STEP 14: Thread in the three supplied socket cup
set screws into the Stealthbox. Make sure that the
socket ends are on the outside of the Stealthbox.
The rear(left side of pic) threaded rods need to
protrude about 1 1/4” out of the Stealthbox.The
front socket cup set screw needs to protrude about
3/4”.
Place the Stealthbox into location. Slide the rear
socket cup set screw through the drilled out holes
from STEP10. Press firmly on the front of the
Stealthbox, marking the wax square.
STEP 16(a): *Tundra Access Cab Only*
Remove the Stealthbox.You should have an impres-
sion on the wax square.
*CAUTION*
Before drilling, make sure that you are not going to
be drilling into any gas lines, brake lines, transmission
lines, electrical wiring, transfer case(4x4 vehicles) or
anything else that might cause a reduction in your
weekly pay. Always wear eye protection when drilling.
With the use of a 1/2” drill bit and drill. Drill out the
floor at the impression on the wax square
STEP 16(b): *Tundra Double Cab Only*
Remove the Stealthbox.You should have an impres-
sion on the wax square.
*CAUTION*
Before drilling, make sure that you are not going to
be drilling into any gas lines, brake lines, transmission
lines, electrical wiring, transfer case(4x4 vehicles) or
anything else that might cause a reduction in your
weekly pay. Always wear eye protection when drilling.
With the use of a 1/2” drill bit and drill. Drill out the
floor at the impression on the wax square
SB- T- T U N C N SL 2 / 1 0 W 3 v 2 , J L AU D I O, I n c 2 0 0 5 Sh e e t S K U # 0 1 1 1 8 0 R e v i s i o n 4 / 6 / 2 0 0 5Pag e 3
w w w . j l a u d i o . c o m
STEP 15: Place the Stealthbox into position, Press
down firmly.


Produktspezifikationen

Marke: JL Audio
Kategorie: Nicht kategorisiert
Modell: Stealthbox SB-T-TUNCNSL2/10W3v3

Brauchst du Hilfe?

Wenn Sie Hilfe mit JL Audio Stealthbox SB-T-TUNCNSL2/10W3v3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert JL Audio

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-