JL Audio Stealthbox SB-GM-HUMRH3/10W1v3 Bedienungsanleitung

JL Audio Nicht kategorisiert Stealthbox SB-GM-HUMRH3/10W1v3

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JL Audio Stealthbox SB-GM-HUMRH3/10W1v3 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
INSTALLATI ON
D I F F I C U L T Y :
I N S T A L L A T I O N G U I D E
for the
SB-GM-HUMRH3/10W1v3
SKU# 94196
2006 - 2010 Hummer H3
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With
proper installation, your new vehicle-specific enclosed subwoofer system will deliver years
of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized
JL Audio dealer. The installation professionals employed by your dealer have the necessary
tools and experience to disassemble and reassemble your vehicle properly. Also, keep in
mind that your warranty coverage extends to 2 year if your system is installed or approved
by your authorized JL Audio dealer. If you prefer to perform your own installation, please
read this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox ® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
S T E P 1
Remove any contents from the rear cargo area and lower the
rear seats forward.
Continued on Next Page
S T E P 2
The driver’s side rear plastic inner fender needs to be
removed.
Using a 10mm socket and ratchet, remove the 5 bolts.
Using a Phillip® head screw driver, remove the 2 screws.
S T E P 3
Pop out the 5 plastic pop-rivets.
The plastic inner fender will drop down.
SB-GM-HUMRH3/10W1v3_ 011215
35
OUT
OF
S T E P 9
With a 10mm socket and ratchet, remove the four bolts that
hold the factory woofer system into place.
Unplug the amplifier and remove the woofer system out of
vehicle.
S T E P 1 1
Thread in the supplied socket cup set screw into the thread-
ed insert, located on the bottom of the Stealthbox®.
Leaving 1/2-inch exposed.
S T E P 1 0
After the factory woofer system has been removed, look
down into the cavity. There is a rubber matting that lays on
top of the wheel well. Cut the front half of this matting out.
Place the wax square to the proper measurements, 3" from
the side wall and 5-1/4-inch from the front wall.
Continued on Next Page
SB-GM-HUMRH3/10W1v3_ 011215
S T E P 7
Remove the top panel.
S T E P 6
With a Phillip® screw driver, remove the screw that is located
under the cover panel.
With a T-50 Torx bit and ratchet, remove the seat belt loop.
S T E P 5
At the driver’s side rear door, remove the door sill.
S T E P 4
From the cargo entrance, remove the weather stripping.
Start at the lower middle. Pull off just past the driver side
paneling.
S T E P 8
Remove the lower panel.
Page 2 • JL Audio, Inc 2016
5 - 1 / 4 "
3 "
S T E P 1 7
Apply the supplied double sided tape to the supplied foam
bar. Apply the foam bar to the back side of the lower cargo
panel that was removed in STEP 8. The foam needs to be
placed below the factory grille opening.
Secure this lower panel back into place.
S T E P 1 9
With a Phillip® screw driver, remount the screw that removed
in STEP 6. Apply factory cover
With a T-50 Torx bit and ratchet, secure the seat belt loop.
Apply factory cover.
S T E P 1 8
Secure the upper panel back into place.
Continued on Next Page
SB-GM-HUMRH3/10W1v3_ 011215
S T E P 1 5
From the outside driver's side rear wheel well; place the sup-
plied fender washer, flat washer, lock washer and then hex
nut onto the protruding socket cup set screw. Secure tightly
with a 14mm socket, long extension and ratchet.
Note: For added protection it is recommended that
you apply a bead of silicone between the vehicle and
the fender washer. After the bolt assembly is tightly
secured, it is also recommended that vehicle under-
coating material is applied to the exposed assembly.
S T E P 1 4
Loosen the socket cup set screw to expose 1-inch. Place the
Stealthbox® into place, carefully guiding the socket cup set
screw through the drilled hole.
Using a supplied bolt and washer, secure the L-bracket to the
top of the enclosure.
(Disregard the woofer grille)
S T E P 1 3
Using a factory bolt that was removed in STEP 9. Mount the
supplied L-bracket to the upper right threaded mounting
hole. One of the same holes that was used to mount the
factory woofer system to the vehicle.
The L-bracket needs be mounted with the protruding angle
to the top.
S T E P 1 2
Position the Stealthbox® into place and press firmly down.
This is to make an impression onto the wax square.
Remove the Stealthbox®.
With a 1/2" drill bit or Step Bit/Unibit® and drill. Drill at the
impression on the wax square, through the floor to the
outside.
Remove the wax square.
(Disregard the woofer grille)
S T E P 1 6
Run speaker wire from the amplifier location to the
Stealthbox® and attach to the terminal.
Check woofer for proper operation.
(Disregard the woofer grille)
Page 3 • JL Audio, Inc 2016


Produktspezifikationen

Marke: JL Audio
Kategorie: Nicht kategorisiert
Modell: Stealthbox SB-GM-HUMRH3/10W1v3

Brauchst du Hilfe?

Wenn Sie Hilfe mit JL Audio Stealthbox SB-GM-HUMRH3/10W1v3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert JL Audio

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-