JL Audio Stealthbox SB-F-RTRKCTR/12W3v3 Bedienungsanleitung

JL Audio Nicht kategorisiert Stealthbox SB-F-RTRKCTR/12W3v3

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JL Audio Stealthbox SB-F-RTRKCTR/12W3v3 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 184 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Stealthbox®®
I N S T A L L A T I O N G U I D E
S B-F-R T R K CTR/ 1 2 W 3 v3, J L A U D IO, I n c 2 0 1 0 S h eet S K U# 0 1 1 1 5 9 R e v i s ion 1 0 .2 1 . 2 0 1 5Pag e 1
for the
SB-F-RTRKCTR/12W3v3
SKU# 94045
2002-2003 Ford SuperCrew
Harley- Davidson, King Ranch,
01-02 Lincoln Navigator, &
02-03 Blackwood
This Stealthbox® is a product which
requires professional installation skills
and tools.
Please read this installation guide thor-
oughly before beginning the project.
It will guide you step by step through
the installation. Several of the steps in
this process may require two people to
accomplish.
It is absolutely vital that the enclo-
sure be properly mounted to the
vehicle according to these instructions.
Failure to mount the enclosure properly
presents two problems: 1) The sub-
bass performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and
2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.
Please enjoy your JL Audio Stealthbo
responsibly.
STEP 1:
Remove the front pocket, inside
insert and rubber flooring.
STEP 2:
With an 8mm socket and long exten-
sion. Remove the four bolts that are located
in the front pocket area.
STEP 3:
(a)Lower the two rear seats and lift
up the drop flooring to expose the bolts.
(b)Remove the pair of bolts from each side,
then remove the OEM console out of the
truck.
STEP 4:
With the OEM console removed,
unbolt the rear U-bracket off the rear wall.
STEP 5:
The Stealthbox® is shipped with two
brackets mounted to it. Remove the rear
angle bracket, from the Stealthbox®. These
bolts are to be used in later a step.
Mount this angle bracket to where the U-
bracket was removed.
Use the three OEM bolts that were removed
in STEP4.
This is also a great time to run speaker
wire from the amplifier location to the
Stealthbox® location. Check the woofer for
proper operation.
STEP 6:
With the Stealthbox® flipped on
it’s back. Remove the bolts that secure the
mounted bracket. Flip the bracket and secure.
The top picture shows the bracket as is
shipped. The bottom picture shows the
bracket, flipped.
START
HERE
Continued on Next Page
w w w . j l a u d i o . c o m
STEP 7:
Place the Stealthbox® into location. Place
a supplied 1spacer between the Stealthbox®® and
the factory bracket. Place a supplied flat washer and
fender washer onto each #8x40mm bolts. Place this
bolt assembly through the Stealthbox®® bracket,
spacer and finger tighten to factory bracket.
STEP 8: (no picture)
Line up the rear of Stealthbox®®
to the rear angle bracket. Using the bolts that
were removed in , secure the rear of the STEP 5
Stealthbox®® to the angle bracket.
Secure all the mounting bolts.
STEP 13:(a)
Cut the inner four tabs, from the
outer console.
Cont.
From
Previous
Page
Continued on Next Page
STEP 9:
With the factory console outside,
remove the four 8mm bolts from bottom of
storage console.
STEP 10:
Remove the seven T-15 Torx screws
from the hinge area and remove the lid.
STEP 13: (b) In some consoles, there are
additional two tabs.They are located on the
rear of outside shell.
STEP 14:
From inside of the truck, place the
outer OEM shell over the Stealthbo®.
Push a supplied plastic tree lock through the
rear bolt holes of the outer shell, into the
Stealthbox®®. Repeat on other side.
STEP 15:(a) Using the OEM screw holes as
guides. Use a 1/8” drill bit, drill into upper
sides of the Stealthbox®®.
(b) To mount the outer shell to the
Stealthbox®®. Use the four OEM screws that
were removed in STEP 12.
STEP 11:
(a)With lid removed, remove the T-
15 Torx screws.
(b)Pull out the inner console from outside
shell.
STEP 12: Remove these four screws.
Remove the inner structure support from
outer shell.
S B-F -R T R K CTR/ 1 2 W 3 v3, J L A U D IO, I n c 2 0 1 0 S h eet S K U# 0 1 1 1 5 9 R e v i s ion 1 0 .2 1 . 2 0 1 5Pag e 2
w w w . j l a u d i o . c o m
STEP 16: Use masking tape to mark cutting line.
IMPORTANT!
Read STEP 16 A and before cutting. B
Us
e a suitable saw to cut OEM storage bucket.
STEP 17: (b) Using an 1/8” drill bit, drill at marked
hole.
Cont.
From
Previous
Page
Continued on Next Page
IMPORTANT!!!!
STEP16(a): Mark/cut 1-1/2 under the upper
lip. Where there is no ledge/reinforcement.
STEP 17: (c) Mount the small angle bracket using
the supplied black rivet and small washer.
STEP 18:(a) Place the modified storage bucket into
the OEM console / top of the Stealthbox®®.
(b) Using the OEM console lid mounting holes as
guides. Drill six holes using an 1/8” drill bit.
STEP 19: Using the six(out of seven) T-15 Torx
screws that were removed in , mount the STEP 10
OEM lid.
STEP 20: With the OEM lid mounted, drill
the “7th” hole using a 1/8” drill bit.
IMPORTANT!
STEP16(b): Where there is a ledge/reinforce-
ment, cut 1-5/16 under.
STEP 17: (a) Line up the supplied small angle
bracket to front middle of OEM inner(cut) console
and mark hole.
S B-F -R T R K CTR/ 1 2 W 3 v3, J L A U D IO, I n c 2 0 1 0 S h eet S K U# 0 1 1 1 5 9 R e v i s ion 1 0 .2 1 . 2 0 1 5Pag e 3
w w w . j l a u d i o . c o m


Produktspezifikationen

Marke: JL Audio
Kategorie: Nicht kategorisiert
Modell: Stealthbox SB-F-RTRKCTR/12W3v3

Brauchst du Hilfe?

Wenn Sie Hilfe mit JL Audio Stealthbox SB-F-RTRKCTR/12W3v3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert JL Audio

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-