JL Audio MicroSub+ ACP208LG-W3v3 Bedienungsanleitung
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂźr JL Audio MicroSub+ ACP208LG-W3v3 (8 Seiten) in der Kategorie Subwoofer. Dieser Bedienungsanleitung war fĂźr 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/8
Thank you for purchasing a JL Audio amplified subwoofer system for
your automotive sound system.
Your subwoofer system has been designed and manufactured to exacting
standards to provide high-quality sub-bass performance and years of
musical enjoyment in your vehicle. For maximum performance, we
highly recommend that you have your new subwoofer system installed
by an authorized JL Audio retailer. Your authorized retailer has the
necessary training, expertise and installation equipment to ensure
optimum performance from this product. Should you decide to install
your subwoofer system yourself, please take the time to read this manual
thoroughly so as to familiarize yourself with it installation requirements
and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your subwoofer systemâs operation, please contact
your authorized JL Audio retailer for assistance. If you need further
assistance, please call the JL Audio Technical Support Department at
(954) 443-1100 during business hours.
OWNERâS MANUAL
MicroSub+ / PowerWedge+
Ampliîed Subwoofer Systems with DCD⢠Ampliîer Technology
50
80
125100
200
Low-Pass
Filter Freq. (Hz )
Turn-On
Mode
Remote
Level
Control
Low-Level Inputs
High-Level
Inputs
FUSE
(30A)
(L ) (R)
Input
Sensitivity
Min. Max.
Signal | DC | Rem 0 | 180 deg.
+12 VDC GND Remote
Output
Polarity
Powe r Conn e ction s
Power
(green)
Protect
(red)
2 JL AUDIOÂŽ
INSTALLATION APPLICATIONS
The built-in amplifier used in this subwoofer
system is designed for operation in vehicles
with 12V, negative-ground electrical systems.
Using this product in systems with positive
ground and/or voltages other than 12V
may result in damage to the product and
will void the warranty. This product is not
certified or approved for use in aircraft.
INSTALLATION PROCEDURE/CONNECTIONS
All connections are located on the amplifier
panel of the enclosure. All connections are made
via RCA-type or quick-disconnect plugs, making it
easy to remove the enclosure quickly, anytime you
need additional space in your vehicle.
1. Disconnect the NEGATIVE battery post
connection and secure the disconnected
cable to prevent accidental reconnection
during installation. This is an essential
safety precaution during installation!
2. Run power wire from the battery location to
the amplifierâs â+12 VDCâ connection, taking
care to route it in such a way that it will not be
damaged and will not interfere with vehicle
operation. 8 AWG is the recommended
power wire size for this amplifier.
3. An appropriate fuse at the main power
wire to the amplifier is vital for vehicle
safety. This fuse must be installed within 18
inches (45 cm) of the positive (+12V) battery
post connection. If this is the only device
connected to this main wire, use a 30A fuse.
Do not install the fuse until the power wire
has been securely connected to the amplifier.
4. Find a good, solid metal grounding point
close to the amplifier panel and connect the
negative power wire to it using appropriate
hardware. Use the same sized wire used
for the +12V connection, no longer than 36
inches (90 cm) from the amplifierâs ground
(GND) connector to the ground connection
point. 8 AWG is the recommended
ground wire size for this amplifier.
5. Run a wire from the source unitâs positive
(+12V) remote turn-on output to the
amplifierâs âRemoteâ connection. If your
source unit does not have a dedicated remote
turn-on output, you may elect to use one of
the automatic turn-on options, configured via
the amplifierâs âTurn-On Modeâ switch. (See
âControl Panel Settings and Adjustments.â)
6. Signal Input (Low-Level): Connect the
amplifierâs RCA input jacks to the source
unitâs preamp level output jacks. You may
run a stereo or a mono signal into the
SAFETY CONSIDERATIONS
⢠Install this subwoofer system in a dry, well-
ventilated location that does not interfere
with your vehicleâs safety equipment (air bags,
seat belt systems, ABS brake systems, etc.).
⢠Securely mount the subwoofer system so
that it does not come loose in the event of
a collision or a sudden jolt to the vehicle.
⢠Check before drilling to make sure that you
will not be drilling into a gas tank, brake line,
wiring harness or other vital vehicle system.
⢠Do not run system wiring outside or
underneath the vehicle. This is an
extremely dangerous practice, which
can result in severe damage/injury.
⢠Protect all system wires from sharp edges by
carefully routing them, tying them down and
using grommets and loom where appropriate.
⢠Secure all wiring as needed, using cable
ties or wire clamps to protect them
from moving parts and sharp edges.
WHATâS INCLUDED
(1) Enclosure with subwoofer(s), built-
in DCD⢠amplifier and grille(s)
(1) Power Connection plug
(1) High-Level input plug
(1) Fuse
(1) User manual
PRODUCT DESCRIPTION
Enclosed subwoofer system with built-
in DCD⢠Class D amplifier and specially
engineered, low-impedance driver(s).
ABOUT DCD⢠TECHNOLOGY
JL Audioâs exclusive DCD⢠amplifier technology
combines direct power conversion with an ultra-
high current output section and unique low-
impedance drivers to extract maximum power and
efficiency. By directly converting a vehicleâs 12V
supply into speaker power, DCD⢠amplifiers are
free of traditional switching power supplies, thus
enabling them to be very compact, while generating
remarkable power output with unprecedented
efficiency (up to 94%). This also permits DCDâ˘
amplifiers to operate at much cooler temperatures
than conventional amplifiers.
WARNING! DCD⢠amplified subwoofer
systems use very specific components. Never
use a DCD⢠amplifier or its companion
subwoofer(s) with incompatible, non-DCDâ˘
products. Doing so will void the warranty
and may cause severe damage/injury.
MicroSub+ / PowerWedge+ with DCD⢠Amplifier Technology 3
POWER CONNECTIONS PLUG
To connect the power wires and remote
turn-on wire to the amplifier, unplug the
âPower Connectionsâ plug from the amplifier
panel (pull back firmly) and back out the set
screws on the connector plug using a Phillips
head screwdriver. Strip 3/8 inch (10 mm) of
insulation from the end of each wire and insert
the bare wire into the receptacle on the power
connector plug, seating it firmly so that no
bare wire is exposed. While holding each wire
in place, tighten each set screw firmly, taking
care not to strip the head of the screw.
Warning! Never make power connections with
a âliveâ wire. Always disconnect the negative
battery post before making any connections or
adjustments to a 12V power connection! Failure
to make safe, tight, high-integrity connections
can result in fire and extensive damage!
inputs of the amplifier. The amplifierâs
input section automatically sums stereo
signals to mono for the internal amplifier
section. When feeding a single, low-level
RCA input connection, use a Y-adaptor
splitter to split the mono signal and connect
it to both Left and Right RCA inputs.
7. Signal Input (High-Level): If your system
does not offer a preamp level signal option,
you can connect speaker level signals directly
to the âHigh-Level Inputsâ connector using
the supplied 4-pin plug and wire harness.
Simply splice the appropriate left/right
and positive/negative wires to the included
harness, and plug the harness into the âHigh-
Level Inputsâ connector on the amplifier. The
amplifier will attenuate the high-level signal
to make it compatible with its input stage.
Refer to the table below for corresponding
wire color information. Make sure to observe
correct polarity in making high-level input
connections. Failure to do so will result
in a loss of signal (poor performance).
8. Make necessary adjustments to the
input sensitivity and filter controls.
9. With the optional RBC-1 Remote Level
Control (sold separately), you can control
the amplifierâs output level from the
front of the vehicle. Connect the RBC-1
to the amplifierâs panel-mounted RJ11
input jack. (Refer to Appendix B)
Remote
Level
Control
Low-Level Inputs
High-Level
Inputs
FUSE
(30A)
(L) (R)
+12 VDC GND Remote
Power Connections
Connection Description
Power
Connections
+ Positive (+12V) Power Connection+12 VDC
â GND Negative (GND) Ground Connection
R Remote Positive (+12V) Remote Turn-On Input
Low-Level Inputs
(RCA Jacks)
(L) White RCA Ch. 1 Input Left Channel Signal Input
(R) Red RCA Ch. 2 Input Right Channel Signal Input
High-Level Inputs
(4-Pin
Connector)
White
Ch. 1 Input
(+) Left Channel Positive
White/Black (â) Left Channel Negative
Gray
Ch. 2 Input
(+) Right Channel Positive
Gray/Black (â) Right Channel Negative
Remote Level Control RJ11 Input Jack for RBC-1 (sold separately)
Produktspezifikationen
| Marke: | JL Audio |
| Kategorie: | Subwoofer |
| Modell: | MicroSub+ ACP208LG-W3v3 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit JL Audio MicroSub+ ACP208LG-W3v3 benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Subwoofer JL Audio
13 Oktober 2024
6 Oktober 2024
4 Oktober 2024
28 September 2024
17 September 2024
15 September 2024
9 September 2024
4 September 2024
4 September 2024
4 September 2024
Bedienungsanleitung Subwoofer
- Subwoofer Philips
- Subwoofer Sony
- Subwoofer Bosch
- Subwoofer Yamaha
- Subwoofer Neumann
- Subwoofer KĂśnig
- Subwoofer MarQuant
- Subwoofer Blaupunkt
- Subwoofer Kenwood
- Subwoofer Sharp
- Subwoofer Atlantic
- Subwoofer Pyle
- Subwoofer Auna
- Subwoofer Bose
- Subwoofer Bowers And Wilkins
- Subwoofer Caliber
- Subwoofer Denon
- Subwoofer Pioneer
- Subwoofer JBL
- Subwoofer JVC
- Subwoofer KEF
- Subwoofer Klipsch
- Subwoofer KrĂźger And Matz
- Subwoofer Onkyo
- Subwoofer Technics
- Subwoofer Teufel
- Subwoofer Hifonics
- Subwoofer Orion
- Subwoofer TCL
- Subwoofer Sencor
- Subwoofer Fenton
- Subwoofer TOA
- Subwoofer Musway
- Subwoofer Adam
- Subwoofer Audio Pro
- Subwoofer Boston Acoustics
- Subwoofer Cabasse
- Subwoofer Canton
- Subwoofer Dali
- Subwoofer Gemini
- Subwoofer Harman Kardon
- Subwoofer Heco
- Subwoofer Magnat
- Subwoofer Mirage
- Subwoofer Power Dynamics
- Subwoofer Skytec
- Subwoofer Tangent
- Subwoofer Vonyx
- Subwoofer Peavey
- Subwoofer HK Audio
- Subwoofer Nova
- Subwoofer Alpine
- Subwoofer Renegade
- Subwoofer LTC
- Subwoofer Behringer
- Subwoofer Mackie
- Subwoofer Omnitronic
- Subwoofer ESI
- Subwoofer MB Quart
- Subwoofer Marantz
- Subwoofer Monoprice
- Subwoofer Arcam
- Subwoofer Cambridge
- Subwoofer Dynacord
- Subwoofer Ecler
- Subwoofer Monacor
- Subwoofer Rockford Fosgate
- Subwoofer Crunch
- Subwoofer Massive
- Subwoofer James
- Subwoofer Jamo
- Subwoofer AXTON
- Subwoofer Clarion
- Subwoofer Mac Audio
- Subwoofer ESX
- Subwoofer AVID
- Subwoofer Nubert
- Subwoofer Insignia
- Subwoofer Audison
- Subwoofer RCF
- Subwoofer Electro-Voice
- Subwoofer Sonos
- Subwoofer Yorkville
- Subwoofer Boss
- Subwoofer Alto
- Subwoofer Genelec
- Subwoofer Tivoli Audio
- Subwoofer Hertz
- Subwoofer Pro-Ject
- Subwoofer Kicker
- Subwoofer AV:link
- Subwoofer Polk
- Subwoofer Speed-Link
- Subwoofer Sonus Faber
- Subwoofer McIntosh
- Subwoofer Sonance
- Subwoofer Jensen
- Subwoofer ELAC
- Subwoofer Fostex
- Subwoofer PreSonus
- Subwoofer Qtx
- Subwoofer Deaf Bonce
- Subwoofer LD Systems
- Subwoofer Bluesound
- Subwoofer DAP Audio
- Subwoofer Definitive Technology
- Subwoofer Energy
- Subwoofer Focal
- Subwoofer Fusion
- Subwoofer Ground Zero
- Subwoofer Helix
- Subwoofer Infinity
- Subwoofer Lanzar
- Subwoofer Martin
- Subwoofer Mission
- Subwoofer Monitor Audio
- Subwoofer Mordaunt Short
- Subwoofer Mtx Audio
- Subwoofer Paradigm
- Subwoofer Phoenix Gold
- Subwoofer Piega
- Subwoofer Q Acoustics
- Subwoofer Quadral
- Subwoofer REL Acoustics
- Subwoofer Soundstream
- Subwoofer Stinger
- Subwoofer Tannoy
- Subwoofer Velodyne
- Subwoofer Wharfedale
- Subwoofer AudioControl
- Subwoofer Martin Audio
- Subwoofer APart
- Subwoofer QSC
- Subwoofer RetroSound
- Subwoofer Proel
- Subwoofer Martin Logan
- Subwoofer Metra
- Subwoofer Kanto
- Subwoofer Fluance
- Subwoofer IMG Stage Line
- Subwoofer Atlas Sound
- Subwoofer FBT
- Subwoofer Eikon
- Subwoofer DB Technologies
- Subwoofer Argon
- Subwoofer Morel
- Subwoofer SVS
- Subwoofer Citronic
- Subwoofer SPL
- Subwoofer Wet Sounds
- Subwoofer Pyramid
- Subwoofer Black Hydra
- Subwoofer GoldenEar Technology
- Subwoofer Roswell
- Subwoofer Audac
- Subwoofer OSD Audio
- Subwoofer Indiana Line
- Subwoofer Match
- Subwoofer Audioengine
- Subwoofer On-Q
- Subwoofer Crestron
- Subwoofer PSSO
- Subwoofer PowerBass
- Subwoofer Dynaudio
- Subwoofer PSB
- Subwoofer KLH Audio
- Subwoofer Extron
- Subwoofer Bazooka
- Subwoofer Theater Solutions
- Subwoofer SSV Works
- Subwoofer Kali Audio
- Subwoofer MadBoy
- Subwoofer Revel
- Subwoofer Nxg
- Subwoofer ANT
- Subwoofer KRK
- Subwoofer Cerwin-Vega
- Subwoofer Sound Ordnance
- Subwoofer Memphis Audio
- Subwoofer Andover
- Subwoofer Aquatic AV
- Subwoofer PrecisionPower
- Subwoofer Totem
- Subwoofer Poly-Planar
- Subwoofer Audiofrog
- Subwoofer Triangle
- Subwoofer Raveland
- Subwoofer Proficient
- Subwoofer Eve Audio
- Subwoofer Planet Audio
- Subwoofer Wavemaster
- Subwoofer Audiotec Fischer
- Subwoofer Origin Acoustics
- Subwoofer PMC
- Subwoofer BMB
- Subwoofer Amina
- Subwoofer Bowers Wilkins
- Subwoofer Chrysalis
- Subwoofer B&W
- Subwoofer Alphasonik
- Subwoofer Glemm
Neueste Bedienungsanleitung fĂźr -Kategorien-
13 Oktober 2024
10 Oktober 2024
7 Oktober 2024
6 Oktober 2024
6 Oktober 2024
2 Oktober 2024
30 September 2024
30 September 2024
29 September 2024
28 September 2024