JL Audio M10IB5 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr JL Audio M10IB5 (4 Seiten) in der Kategorie Subwoofer. Dieser Bedienungsanleitung war fĂĽr 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Thank you for choosing a JL Audio Marine Subwoofer.
With proper installation, your new speaker
will deliver years of listening pleasure.
We strongly recommend that you have your subwoofer installed
by your authorized JL Audio dealer. The installation
professionals employed by your dealer have the necessary tools and experience to
properly install this product. If you prefer to perform
your own installation, please read this instruction manual
completely before beginning the process.
owner’s manual
Marine Subwoofer
M10IB5 / M10W5
2 JL AUDIO M10IB5/M10W5
A
C
B
E
D
INSTALLATION PROCEDURE
The diagram above shows the typical
installation procedure into a fiberglass panel using
the supplied hardware (Classic Grille Model shown.
Installation is the same for Sport Grille Models).
Always follow proper safety procedures when
working on a vessel. Use eye-protection at all times
and a dust mask and gloves when cutting.
1) Choose a flat mounting surface that has
sufficient
depth and air space behind it to accept
the subwoofer.
2) Cut a 8.875-inch (225 mm) diameter hole.
3) Run the speaker cable to the mounting location.
4) Place the woofer in the hole and mark the screw
hole locations using a sharp, pointed tool.
5) Remove the woofer and drill a pilot hole
(see chart on next page) in each of the screw
locations. It is also advisable to use a hand-driven
countersink tool on each hole to further inhibit
gel-coat cracking of fiberglass panels.
6) Connect the speaker wires and place the woofer,
with its grille in place, into the opening (for Sport
Grille models, pay attention to where the logo
badge will added.
7) While holding the speaker firmly in its mounting
location, evenly snug the mounting screws in a
criss-cross pattern, then hand tighten in a criss-
cross pattern.
Non-standard installations may require different
hardware. Always use marine-grade, stainless-steel
fasteners to ensure a secure, reliable installation.
We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers.
We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely
affect performance.
A l l s p e c i f i c a t i o n s a r e s u b j e c t t o c h a n g e w i t h o u t n o t i c e .
PHYSICAL SPECIFICATIONS
INCLUDED PARTS
• One Polymer Subwoofer Grille
• Six #10 x 1 5/8-inch (41 mm) pan-head
stainless-steel screws
• Six #10 stainless-steel washers
• Logo Badges (Sport-Grille Models Only)
One Pair Black (White & Titanium/Black Models)
One Pair Red (White & Titanium/Black Models)
One Pair White (White Models Only)
One Pair Titanium (Titanium/Black Models Only)
Subwoofer Physical Specifications
Nominal Diameter: 10 in. / 250 mm
Overall Diameter (A): 10.75 in. / 273 mm
Mounting Hole Diameter (B): 8.875 in. / 225 mm
Bolt Hole Circle (C): 9.706 in. / 247 mm
Motor Overmold Outer Diameter (D): 6.11 in. / 155 mm
Mounting Depth (E): 5.93 in. / 151 mm
Net Weight: 11.4 lbs. / 5.17 Kg
Driver Displacement: 0.064 ft / 1.81 litres
Subwoofer Parameters M10IB5 M10W5
Free Air Resonance (Fs): 42.20 Hz 31.55 Hz
Electrical “Q” (Qes): 0.819 0.484
Mechanical “Q” (Qms): 10.355 8.946
Total Speaker “Q” (Qts): 0.759 0.460
Equivalent Compliance (Vas): 1.16 ft3 / 32.85 litres 1.58 ft3 / 44.75 litres
One-way, Linear Excursion (Xmax)*: 0.52 in. / 13.2 mm 0.52 in. / 13.2 mm
Efficiency (1W/1m)**: 86.8 dB SPL 86.7 dB SPL
Effective Piston Area (Sd): 50.11 in² / 0.0323 m² 50.11 in² / 0.0323 m²
DC Resistance (Re): 4.167 ohm 3.602 ohm
Nominal Impedance: 4 ohm 4 ohm
Infinite Baffle Use: Yes No
Enclosure Use: Yes (Sealed Only) Yes (Sealed and Ported)
Power Handling (continuous): 250W 250W
* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.
** Efficiency (1W/1m) is not an accurate indicator of a subwoofer’s output capability and should not be used
as a comparison to other subwoofers to determine which one is “louder” !
The enclosure recommendations listed are external dimensions which assume the use of 3/4” (19mm) thick material. If you are using 5/8” (16mm) thick material, subtract 1/4”
(6.5mm) from each dimension. Do not use any material with a thickness of less than 5/8” (16mm) as this may compromise the rigidity of the enclosure.
All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal
volume. All enclosure dimensions listed have already taken this into account.
JL AUDIO M10IB5/M10W5 3
INTERCHANGEABLE LOGO BADGE
(Sport-Grille Models Only)
Interchangeable Logo Badges for Sport Grille
model subwoofers are included to further customize
your installation. The design of the Sport Grille allows
for the JL Audio logo to be added in your choice of
included colors and oriented in the manner that best
suits your installation.
NOTE: A left and a right badge of each color is
included. These two different orientations ensure
the “JL Audio” Logo will read correctly wherever
positioned (most commonly the 3:00 or 9:00
position).
Remove the adhesive backing from the badge
and affix the badge to the grille using the small
positioning hole as a guide. See diagram at right.
! ! CAUTION ! !
While this speaker is designed to be water and
spray resistant, it is not designed to be submerged
or to withstand high-pressure water spray.
Please exercise care when washing your boat to
avoid damaging your speaker. Do not install on
submersibles, personal watercraft or any other
vessel likely to be under water at any time.
Prolonged exposure to sound pressure levels in
excess of 100dB can cause permanent hearing loss.
This high-performance speaker can exceed this
level. Please exercise restraint in its operation in
order to preserve your ability to enjoy its fidelity.
When installing a subwoofer in your vessel, it is
extremely important to secure it firmly. This applies
not only to the woofer itself, but also the structure
it is mounted to. If not firmly attached, the speaker
can become a dangerous projectile in a collision.
Please review the mounting information carefully
and use the supplied marine-grade hardware to
mount this product.
A l l s p e c i f i c a t i o n s a r e s u b j e c t t o c h a n g e w i t h o u t n o t i c e .
Fiberglass Thickness Recommended Pilot Hole Drill Size
0.125 in. (3.18 mm) or less 1/8 in. (3.18 mm) pilot hole
foam core / fiberglass sandwich 1/8 in. (3.18 mm) pilot hole
larger than 0.125 in. (3.18 mm) 9/64 in. (3.57 mm) pilot hole
#10 SCREW: PILOT HOLE RECOMMENDATIONS
3:00 Position
9:00 Position
Subwoofer Recommended Sealed Design
Volume
(net int.)
External Dimensions
( idth x eight x epth)W H D
F3
(Hz)
Fc
(Hz) Qtc
M10W5 0.875 ftÂł
24.8 litres
14 in. x 14 in. x 12 in.
356 mm x 356 mm x 305 mm 49 52.85 .770
M10IB5 2.50 ftÂł
70.8 litres
18 in. x 18 in. x 17.75 in.
457 mm x 457 mm x 451 mm 42 .91851.06
Subwoofer Recommended Ported Design
Volume
(net int.)
Enclosure External Dimensions
( idth x eight x epth)W H D
Round Port Specs
( nner I Diameter x Length) Port Information Tune to:
(Hz)
F3
(Hz)
M10W5 1.250 ftÂł
35.4 litres
16.5 in. x 13.5 in. x 14 in.
419 mm x 343 mm x 356 mm
3 in. x 13 in.
76 mm x 330 mm
Round port requires a 90Ëš elbow
to fit in the specified enclosure 32 34
Sealed Design Ported Design
ENCLOSURE SPECIFICATIONS
NOTE: The M10IB5 Marine Subwoofer is not
recommended for use in Ported Enclosures.


Produktspezifikationen

Marke: JL Audio
Kategorie: Subwoofer
Modell: M10IB5

Brauchst du Hilfe?

Wenn Sie Hilfe mit JL Audio M10IB5 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Subwoofer JL Audio

Bedienungsanleitung Subwoofer

Neueste Bedienungsanleitung fĂĽr -Kategorien-