JL Audio M-LCB-C-W Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr JL Audio M-LCB-C-W (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Installation Instructions for
M-LCA-C-W
&
M-LCB-C-W
L E D L I G H T C A P
FOR ETXv e3 & V X™ ENCLOSED SPE AKER SYSTEMS
NOTE: The M-LCA-C-W Light Cap and M880-ETXv3-SG-WH Enclosed Speaker System are
used in this manual for illustrative purposes only. The installation steps are the same for
all ETXv3 and VeX™ Enclosed Speaker Systems and all LED Light Caps.
LIMITED WARRANTY  MARINE PRODUCTS USA
JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two (2) years from the
original date of purchase.
This warranty is not transferable and applies onl y to the original purchaser from an authorized JLAUDIO dealer. Should service
be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL AUDIO will (at its discretion),
repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not
covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions,
unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential dam ages
and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not
covered under warranty.
Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning
with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product
thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For Service Information in the U.S.A. please call
JL Audio Customer Service: (954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc
10369 North Commerce Pkwy.
Miramar, FL 33025, USA
International Warranties:
Products purchased outside the United States of America are covered only
by that country’s distributor and n ot by JL Audio, Inc.
w w w . j l a u d i o . c o m
JL Audi o® and the JL Audi o logo are re gistere d trademar ks of JL Aud io, Inc. “Ahead of the Curve” and its resp ective logo is a trad emark of JL Au dio, Inc.
©2017 JLAud io, Inc. • For m ore detailed inform ation plea se visit us online at Due to ou r policy o f continuous produc t developm ent, all sp ecifications are su bject to change without notice. www.jlaudio.com.
Included Hardware: BOM ID Quantity Description
1 1 M10 Locknut Tool
2 2 M10 x 1.5 Nylon Insert Flange Locknut
3 2 LED Light Cap
4* 2 readed Stud
5* 2 O-Ring
- 2 150mA Fuse (not shown)
- 2 Fuse Holder (not shown)
- 2 Female Connector (not shown)
Note: Not all wires may be used in normal applications.
Wire Size Wire Color Use
16 AWG Red/Stripe Speaker Positive (+)
Black/Stripe Speaker Negative (–)
20 AWG
Red LED Light Cap Positive (+)
Green LED Light Cap Negative (-)
Blue Speaker LED Positive (+)
Yellow Speaker LED Negative (–)
* Pre-installed on LED Cap
(hardware pictured for one)
Enclosed Speaker System Wiring:
Wire Size Wire Color Use
18 AWG Red LED Positive (+)
Black LED Negative (–)
LED Light Cap Wiring:
Printed in U.S.A. • 112017
Remove the six #8 x 1-1/4” Pan Head Screws and six #8
Flat Washers that secure the speaker to the enclosure.
1
Connect the LED wires from the LED Light Cap to the
LED wires entering the enclosure. Refer to the wiring
charts on the opposite page for details. DO NOT install
the fuse holders inside the enclosure.
9
Using the exterior angles of the JL Audio logo as a
guide, mark the center of the rear aluminum logo cap,
as shown. Using a punch tool, make an indent in the
aluminum logo cap on the center mark.
3
Slide the M10 Locknut Tool over the LED wires and onto
the M10 x 1.5 Nylon Insert Flange Locknut.
7
Disconnect the speaker wiring and speaker LED
wiring (if equipped), and remove the speaker from the
enclosure.
2
Slide an M10 x 1.5 Nylon Insert Flange Locknut over the
LED wiring, and hand-tighten onto the readed Stud.
6
Using a 7/16” drill bit, carefully drill through the center of
the rear aluminum logo cap, into the enclosure. File any
sharp edges.
4
Reconnect the speaker wiring, and reinstall the speaker
using the six #8 x 1-1/4” Pan Head Screws and six #8
Flat Washers.
10
Rotate the LED Light Cap to the desired angle. Using the
M10 Locknut Tool, fully tighten the M10 x 1.5 Nylon Insert
Flange Locknut until the O-ring is fully compressed and not
visible to ensure the unit is properly sealed. Remove the M10
Locknut Tool from the enclosure.
8
Pass the LED wires and readed Stud on the back of the
LED Light Cap through the drilled hole, and position the
cap ush against the back of the enclosure.
5
• For marine installations, do not connect the LED lights
to the vessel’s navigational lighting circuits.
• For short-circuit protection, install a supplied fusehold-
er onto EACH LED Light Cap’s RED (+12V) LED power
connection lead.
• Connect all RED (+12V) leads together (parallel) and
connect to a switched +12V supply. Connect all
GREEN (GND) leads together and connect to a
negative ground or to the NEGATIVE battery post.
• We recommend activating the LEDs thru a lighting
circuit that supplies +12V via an existing switch. If an
existing switched circuit is not available, you may install
a dedicated toggle/rocker style switch that will supply
positive (+12V) power. Fuse this connection according
to how many LED circuits you have (LED circuits x
150 mA).
[ D]GN
LED
[+12V]
Blue
Yellow
Blue
Yellow
Red
Black
Red
Black
LED
Fuse
Fuse
Fuse
[ D]GN
[+12V]
Blue
Yellow
Red
Black
Blue
Yellow
Red
Black
Blue
Yellow
Red
Black
Blue
Yellow
Red
Black
LED
LED
LED
LED
Fuse
Fuse
Fuse
Fuse
Fuse
Example: One pair of LED circuits
connected in parallel.
Example: Two pairs of LED circuits
connected in parallel.


Produktspezifikationen

Marke: JL Audio
Kategorie: Nicht kategorisiert
Modell: M-LCB-C-W

Brauchst du Hilfe?

Wenn Sie Hilfe mit JL Audio M-LCB-C-W benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert JL Audio

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-