Jenn-Air UDT555SAHP Bedienungsanleitung

Jenn-Air Spülmaschine UDT555SAHP

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Jenn-Air UDT555SAHP (17 Seiten) in der Kategorie Spülmaschine. Dieser Bedienungsanleitung war für 26 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/17

DISHWASHER

USER INSTRUCTIONS

Dishwasher Safety

Table of Contents

THANK YOU for purchasing this high-quality product. Register your new dishwasher at www.whirlpool.com. In Canada, visit our website

at www.whirlpool.ca.

Get Internet connection instructions, terms of use, and privacy policy at www.whirlpool.com/connect. If you have any problems or

questions, call the Whirlpool Connected Appliance Team at . In Canada, visit 1-866-333-4591 www.whirlpool.ca/en_CA and click on the

Whirlpool ® Connected Appliances link.

For future reference please make a note of your product model and serial numbers. These can be located near the door on the

right-hand or left-hand side of the dishwasher interior.

Model Number _____________________________________________ Serial Number _____________________________________________

W10901525B

DISHWASHER SAFETY 1 ..............................................................

CONNECTED APPLIANCE REGULATORY NOTICE 3 .................

WHAT’S NEW IN YOUR DISHWASHER 4 .....................................

PARTS AND FEATURES 5 .............................................................

QUICK STEPS 6 ............................................................................

CONNECTIVITY FEATURES 6 .......................................................

CONNECTIVITY SETUP 7 ..............................................................

DISHWASHER USE – BASIC OPERATION 8 ................................

DISHWASHER USE – SMART OPERATION 10 ............................

CYCLE AND OPTION DESCRIPTIONS....................................11

DISHWASHER FEATURES 14 .......................................................

FILTRATION SYSTEM 16 ...............................................................

DISHWASHER CARE 17 ................................................................

TROUBLESHOOTING – CONNECTIVITY 18 ................................

TROUBLESHOOTING 20 ...............................................................

OPEN SOURCE LICENSE USAGE 23 ...........................................

WARRANTY 24 ...............................................................................

IMPORTANT SAFETY INSTRUCTIONS

WARN G:IN When using the dishwasher, follow basic precautions, including the following:

SAVE THESE INSTRUCTIONS

■ Read all instructions before using the dishwasher.

■ Use the dishwasher only for its intended function.

■ Use only detergents or rinse agents recommended for use in

a dishwasher, and keep them out of the reach of children.

■ When loading items to be washed:

1) Locate sharp items so that they are not likely to damage

the door seal; and

2) Load sharp knives with the handles up to reduce the risk

of cut-type injuries.

■ Do not wash plastic items unless they are marked

“dishwasher safe” or the equivalent. For plastic items not so

marked, check the manufacturer's recommendations.

■ Do not touch the heating element during or immediately after

use.

■ Do not operate the dishwasher unless all enclosure panels

are properly in place.

■ Do not tamper with controls.

■ Do not abuse, sit on, or stand on the door, lid, or dish racks

of the dishwasher.

■ To reduce the risk of injury, do not allow children to play in

or on the dishwasher.

■ Under certain conditions, hydrogen gas may be produced in

a hot water system that has not been used for two weeks or

more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

system has not been used for such a period, before using

the dishwasher turn on all hot water faucets and let the

water flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is flammable,

do not smoke or use an open flame during this time.

■ Remove the door or lid to the washing compartment

when removing an old dishwasher from service or

discarding it.

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■ For a grounded, cord-connected dishwasher:

The dishwasher must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for

electric current. The dishwasher is equipped with a cord

having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet

that is installed and grounded in accordance with all local

codes and ordinances.

WARN G:IN Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

if you are in doubt whether the dishwasher is properly

grounded. Do not modify the plug provided with the

dishwasher; if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

■ For a permanently connected dishwasher:

The dishwasher must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the dishwasher.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

WARNING

Connected Appliance Regulatory Notices

Federal Communications Commission (FCC)

Compliance Notice

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for

help. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

Changes or modications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

RF Exposure Information

To comply with FCC/IC RF exposure requirements for mobile

transmitting devices, this transmitter should only be used or

installed at locations where there is at least 20 cm separation

distance between the antenna and all persons.

To comply with FCC/IC RF exposure limits for general

population/uncontrolled exposure, the antenna(s) used for this

transmitter must be installed to provide a separation distance of

at least 20 cm from all persons and must not be co-located or

operating in conjunction with any other antenna or transmitter.

Industry Canada (IC) Compliance Notice

This Device complies with Industry Canada License-exempt RSS

standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference,

2. This device must accept any interference, including

interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may

only operate using an antenna of a type and maximum (or lesser)

gain approved for the transmitter by Industry Canada. To reduce

potential radio interference to other users, the antenna type and its

gain should be so chosen that the equivalent isotropically radiated

power (e.i.r.p.) is not more than that necessary for successful

communication.

The radio transmitters IC: 10248A-WICHAM01 and

10248A-FLDAAM01 have been approved by Industry Canada to

operate with the antenna types listed below with the maximum

permissible gain and required antenna impedance for each

antenna type indicated. Antenna types not included in this list,

having a gain greater than the maximum gain indicated for that

type, are strictly prohibited for use with this device.

Antenna Type Maximum Permissible

Antenna Gain (dBi)

Required

Impendance

(OHM)

Slot 1.2 50

Monopole

(WICHAM01 only) 0.5 50

Dipole 3.0 50

F 1.60 50

Planar F 4.2 50

To comply with FCC and Industry Canada RF radiation exposure

limits for general population, the antenna(s) used for this

transmitter must be installed such that a minimum separation

distance of 20 cm is maintained between the radiator (antenna)

and all persons at all times and must not be co-located or

operating in conjunction with any other antenna or transmitter.

Le présent appareil est conforme aux CNR d’Industrie Canada

applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement. Conformément à la réglementation

d’Industrie Canada, le présent émetteur radio peut fonctionner avec

une antenne d’un type et d’un gain maximal (ou inférieur) approuvé

pour l’émetteur par Industrie Canada. Dans le but de réduire

les risques de brouillage radioélectrique à l’intention des autres

utilisateurs, il faut choisir le type d’antenne et son gain de sorte que

la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse

pas l’intensité nécessaire à l’établissement d’une communication

satisfaisante. Le émetteurs radio IC : 10248A-WICHAM01et

10248A-FLDAAM01ont été approuvés par Industrie Canadapour

fonctionner avec les types d’antenne énumérés ci-dessous et ayant

un gain admissible maximal et l’impédance requise pour chaque

type d’antenne. Les types d’antenne non inclus dans cette liste, ou

dont le gain est supérieur au gain maximal indiqué, sont strictement

interdits pour l’exploitation de l’émetteur.

Type d’antenne Gain

admissiblemaximal

d’antenne (dBi)

L’impédance

requise (OHM)

À fentes 1.2 50

Monopôle (WICHAM01

seulement) 0.5 50

Dipole 3.0 50

F 1.60 50

Planaire F 4.2 50

Pour satisfaire aux exigences de la FCC et IC d’exposition aux

radiofréquences, une distance de séparation de 20 cm ou plus

doit être maintenue entre cet appareil et des personnes lors de

fonctionnement du dispositif. Pour assurer la conformité des

opérations au plus près que cette distance n’est pas recommandée.

L’antenne utilisée pour ce transmetteur ne doit pas être co-localisés

en conjonction avec toute autre antenne ou transmetteur.

OEM Responsibilities to comply with FCC and Industry Canada

Regulations

The WICHAM01/FLDAAM01 Modules have been certied for

integration into products only by OEM integrators under the

following conditions:

1. The antenna(s) must be installed such that a minimum

separation distance of 20 cm is maintained between the

radiator (antenna) and all persons at all times.

2. The transmitter module must not be co-located or operating in

conjunction with any other antenna or transmitter.

As long as the two conditions above are met, further transmitter

testing will not be required. However, the OEM integrator is

still responsible for testing their end-product for any additional

compliance requirements required with this module installed (for

example, digital device emissions, PC peripheral requirements,

etc.).

IMPORTANT NOTE: In the event that these conditions cannot

be met (for certain congurations or co-location with another

transmitter), then the FCC and Industry Canada authorizations

are no longer considered valid and the FCC ID and IC

Certication Number cannot be used on the nal product. In

these circumstances, the OEM integrator will be responsible

for re-evaluating the end product (including the transmitter) and

obtaining a separate FCC and Industry Canada authorization.

End Product Labeling

The WICHAM01/FLDAAM01 Modules are labeled with FCC ID and

IC Certication Number. If the FCC ID and IC Certication Number

are not visible when the module is installed inside another device,

then the outside of the device into which the module is installed

must also display a label referring to the enclosed module. In that

case, the nal end product must be labeled in a visible area or

display the following:

“Contains FCC ID: A5UWICHAM01”

“Contains IC: 10248A-WICHAM01”

“Contains FCC ID: A5UFLDAAM01”

“Contains IC: 10248A-FLDAAM01”

The OEM of the WICHAM01/FLDAAM01 Module must only use the

approved antenna(s), which have been certied with this module.

The OEM integrator has to be aware not to provide information to

the end user regarding how to install or remove this RF module

or change RF related parameters in the user manual of the end

product.

The user manual for the end product must include the

following information in a prominent location:

“To comply with FCC and Industry Canada RF radiation exposure

limits for general population, the antenna(s) used for this

transmitter must be installed such that a minimum separation

distance of 20 cm is maintained between the radiator (antenna)

and all persons at all times and must not be co-located or

operating in conjunction with any other antenna or transmitter.”

Produktspezifikationen

Marke:	Jenn-Air
Kategorie:	Spülmaschine
Modell:	UDT555SAHP

Brauchst du Hilfe?

Wenn Sie Hilfe mit Jenn-Air UDT555SAHP benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Spülmaschine Jenn-Air

Jenn-Air JDAF3924RX Bedienungsanleitung

6 September 2024

Jenn-Air JDPSS244PL Bedienungsanleitung

6 September 2024

Jenn-Air JDTSS244GM Bedienungsanleitung

6 September 2024

Jenn-Air JDTSS244GL Bedienungsanleitung

6 September 2024

Jenn-Air JDTSS245GX Bedienungsanleitung

6 September 2024

Jenn-Air JDTSS246GM Bedienungsanleitung

6 September 2024

Jenn-Air UDT555SAHP Bedienungsanleitung

6 September 2024

Jenn-Air JDTSS243GX Bedienungsanleitung

6 September 2024

Jenn-Air JDTSS244GS Bedienungsanleitung

6 September 2024

Jenn-Air JDTSS246GL Bedienungsanleitung

6 September 2024

Bedienungsanleitung Spülmaschine

Neueste Bedienungsanleitung für -Kategorien-

Siemens 15 Bedienungsanleitung

12 Dezember 2023

Exquisit EGSP130-E Bedienungsanleitung

11 Mai 2024

BEKO BDFN26530B Bedienungsanleitung

4 Dezember 2024

BEKO BDEN38560CHPA Bedienungsanleitung

4 Dezember 2024

BEKO BDIN16520Q Bedienungsanleitung

4 Dezember 2024

BEKO BDFN15421W Bedienungsanleitung

4 Dezember 2024

BEKO BDIN15320 Bedienungsanleitung

4 Dezember 2024

BEKO BDFS15020B Bedienungsanleitung

4 Dezember 2024

BEKO BDFS15020S Bedienungsanleitung

4 Dezember 2024

BEKO BDFN15421S Bedienungsanleitung

4 Dezember 2024