JBL LSR705i Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JBL LSR705i (10 Seiten) in der Kategorie Monitor. Dieser Bedienungsanleitung war für 23 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/10
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/de/jbl/lsr705i/html/bg1.png)
Set Up Instructions
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/de/jbl/lsr705i/html/bg2.png)
7 Series “i” Set Up Instructions
7 Models 2SeriesInstalled SetUpPage 8/1/16
In preparation for set up you will need:
One of more JBL 7 Series “i” model speakers
A recommended Harman Crown Power Amplifier
OR Harman BSS Soudweb London processor AND an amplifier with suitable power
Mounting hardware
Speaker Wire
Balanced line level input cables
Female XLR to “phoenix” adaptors if needed
A computer with Windows 7 operating system and to which you have administrative privileges and access to the
internet and HiQnet Audio Architect Software installed or London Architect Software installed.
Category 5e Cable
An Ethernet switch if more than one Crown DCi power amplifier is used.
Small flat Head screwdriver
Phillips screwdriver
Support:
JBL Customer Support is available Monday through Friday 8:00am - 5:00pm Pacific Coast Time in the U.S.A.
+1 (800.852.5776), www.jblproservice.com
Audio Architect Software with Crown Amplifiers, please contact Crown Customer Support at +1 (800) 342-6939
Monday through Thursday 9:00am - 7:00pm, Friday: 9:00am - 5:00pm Eastern Standard Time in the U.S.A.
www.crownaudio.com/techsupport
London Architect Software with BSS Soundweb London processors, please contact BSS Customer Support at +1
(800) 931-2357 during the hours of 8:00am - 5:00pm Mountain Time in the U.S.A www.bssaudio.com/en-US/support
Outside the USA: Contact the HARMAN Professional Distributor in your area. A complete list of HARMAN
international distributors is provided on our U.S.A. website: www.jblpro.com
Installation and Mounting of Speakers
7 Series “i” model enclosures are reinforced to allow safe mounting and include mounting points on the top,
bottom and rear panel of the speaker. Speaker dimensional drawings, location of mounting points, and
mounting hardware requirements can be found at the end of this document, The speakers can be installed
using readily available mounting brackets. A range of brackets are available from Adaptive Technologies
Group 1635 E. Burnette Street, Signal Hill, California, USA 90755 Telephone: +1 (562) 273-4239
design@adapttechgroup.comwww.adapttechgroup.com Bracket models can be found at the end of this
document.
Caution: When installing speakers, observe safe mounting practices and recommendations provided by
mounting hardware manufacturer. Do not modify the speaker enclosure.
Amplifier and Power Requirements
The 708i and 705i models require use of an external power amplifier capable of delivering 300 watts per channel and
also Harman Professional digital signal processing. The following Harman Crown Audio power amplifiers include the
required Harman Digital Signal Processing and are recommended:
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/de/jbl/lsr705i/html/bg3.png)
7 Series “i” Set Up Instructions
7 Models 3SeriesInstalled SetUpPage 8/1/16
• DCi 2|300N 2 channel power amplifier
• DCi 4|300N 4 channel power amplifier
• DCi 8|300N 8 channel power amplifier
A DCi 8|300 power amplifier supplies power for up to eight speakers,
or up to four bi-amplified speakers or any combination of single and
bi-amplified speakers. A detailed owner’s manual can be downloaded
at www.crownaudio.com Crown DCi “N” networked models include
the required digital signal processing for 7 Series speaker tuning
profiles and also additional filters that can be used as room eq.
Additionally, these amplifiers accept digital signals via HARMAN BLU
link audio protocol. If you wish to use an amplifier other than the
Crown DCi Networked models specified above, you must also use a
HARMAN BSS Soundweb™ London Signal Processor. Information
about BSS Soundweb London Processors and accessories is
available at www.bssaudio.com
The Crown DCi models incorporate internal fans that are engaged full-
time ensure the operating temperature of the power amp does not
exceed specified thermal conditions. It is preferable to locate power
amplifiers outside the listening area.
Connections and Wiring
Speaker Inputs:
The 708i and 705i can be powered using a single amplifier channel or bi-amplified using separate amplifier channels
for the low frequency and high frequency drivers. The speakers are supplied with “phoenix” type Euro-block wiring
plugs installed. Remove and connect speaker wire to EITHER the plug inserted in the connector labeled Single Wire
OR the plug inserted in the connector labeled Bi-Amplified. When operating the speaker using the Single Wire
connection, the supplied plug must remain inserted in the Bi-Amplified connector. Removing this plug will prevent
single wire operation. Replacement plugs can be obtained by contacting JBL Customer Service at
www.jblpro.com/support.
Dedicated DSP device files are required for single wire and bi-amplified operation. These are available for download
at www.jblpro.com/7series.
The speakers should be connected to the power amplifier using two conductor speaker wire. We recommend the
use of high quality 12-gauge oxygen-free copper stranded wire, readily available from electronics retailers. Using 12-
gauge wire, the speaker can be placed up to 100 feet from the power amplifier.
Crown Amplifier Inputs
Signal sources should be connected to Crown power amplifiers using
balanced line level cables. Crown Power amplifiers feature balanced
analog inputs using “phoenix” type connectors. For use with XLR,
balanced ¼” TRS and other connectors, adaptors should be used.
Crown recommends using pre-built or professionally wired balanced
cables (two-conductor plus shield). Balanced wiring provides better
rejection of unwanted noise and hum; however, unbalanced line may
also be used. Use 6-pin plug-in cable ends at the amp input connectors.
A male connector is supplied for each input of your model of amplifier.
Additional connectors are available from Crown (P/N 5024623). Figure
3 shows connector pin assignments for balanced wiring and Figure 4
Produktspezifikationen
Marke: | JBL |
Kategorie: | Monitor |
Modell: | LSR705i |
Brauchst du Hilfe?
Wenn Sie Hilfe mit JBL LSR705i benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Monitor JBL
![JBL](/images/logos/jbl.png)
17 Januar 2024
![JBL](/images/logos/jbl.png)
14 Mai 2023
Bedienungsanleitung Monitor
- Monitor Samsung
- Monitor Da-Lite
- Monitor 3M
- Monitor Acer
- Monitor Apple
- Monitor Asus
- Monitor Sanyo
- Monitor BenQ
- Monitor Gigabyte
- Monitor HP
- Monitor Medion
- Monitor Philips
- Monitor Sony
- Monitor Panasonic
- Monitor LG
- Monitor Bosch
- Monitor Denver
- Monitor EMOS
- Monitor Renkforce
- Monitor Sharp
- Monitor Triton
- Monitor Pyle
- Monitor Mitsubishi
- Monitor Haier
- Monitor JVC
- Monitor Optoma
- Monitor Stairville
- Monitor Abus
- Monitor Continental Edison
- Monitor Hannspree
- Monitor Hitachi
- Monitor Hyundai
- Monitor Orion
- Monitor Toshiba
- Monitor Omron
- Monitor Element
- Monitor ViewSonic
- Monitor Dell
- Monitor LC-Power
- Monitor Lenovo
- Monitor MSI
- Monitor Adam
- Monitor Burg Wächter
- Monitor Marshall
- Monitor Razer
- Monitor Samson
- Monitor ELO
- Monitor Marshall Electronics
- Monitor Terra
- Monitor Xoro
- Monitor Smart
- Monitor Cooler Master
- Monitor Faytech
- Monitor Behringer
- Monitor Mackie
- Monitor Barco
- Monitor NEC
- Monitor Monoprice
- Monitor Fujitsu
- Monitor Huawei
- Monitor Packard Bell
- Monitor JUNG
- Monitor Westinghouse
- Monitor AOC
- Monitor AG Neovo
- Monitor Eizo
- Monitor Iiyama
- Monitor Skytronic
- Monitor DataVideo
- Monitor RCF
- Monitor Boss
- Monitor IFM
- Monitor Genelec
- Monitor Wortmann AG
- Monitor Asrock
- Monitor CTOUCH
- Monitor Hikvision
- Monitor Newline
- Monitor Fostex
- Monitor PreSonus
- Monitor Oecolux
- Monitor Baaske Medical
- Monitor Ikan
- Monitor Avantone Pro
- Monitor Emachines
- Monitor Focal
- Monitor HKC
- Monitor LaCie
- Monitor Tannoy
- Monitor AMX
- Monitor Vimar
- Monitor Alienware
- Monitor Ozone
- Monitor ITek
- Monitor TV One
- Monitor Planar
- Monitor Bematech
- Monitor Dahua Technology
- Monitor Posiflex
- Monitor Speco Technologies
- Monitor Christie
- Monitor Hanwha
- Monitor Allsee
- Monitor Aputure
- Monitor Lilliput
- Monitor Crestron
- Monitor I3-Technologies
- Monitor Pelco
- Monitor Dynaudio
- Monitor V7
- Monitor Sonifex
- Monitor Alogic
- Monitor DoubleSight
- Monitor Nixeus
- Monitor Drawmer
- Monitor Gamber-Johnson
- Monitor Raysgem
- Monitor Viotek
- Monitor ANDYCINE
Neueste Bedienungsanleitung für -Kategorien-
![Philips](/images/logos/philips.png)
4 Juli 2024
![Samsung](/images/logos/samsung.png)
4 Juli 2024
![Acer](/images/logos/acer.png)
4 Juli 2024
![Acer](/images/logos/acer.png)
4 Juli 2024
![Acer](/images/logos/acer.png)
4 Juli 2024
![Medion](/images/pdf_free.png)
3 Juli 2024
![Huawei](/images/logos/huawei.png)
3 Juli 2024
![Samsung](/images/logos/samsung.png)
3 Juli 2024
![Medion](/images/pdf_free.png)
3 Juli 2024