JANDY MiniJet Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JANDY MiniJet (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
The Polaris MiniJet for vinyl liner pools (FFMJ-VL) is
designed to mount in a vinyl pool wall slightly above
water level. It can be mounted in wall panels with a
thickness of .1094” (12Ga. Steel) to 3/8” (polymer
wall). For deck installations, use the standard Polaris
MiniJet (FFMJ).
Preparing For Installation
Determine the mean water level of the pool and
the vertical center line of each MiniJet. If water
covers the nozzle, the performance will be affected.
Mounting it too high may interfere with the coping
and liner installation.
Pressure testing is required. Screw the 3/8” plug
provided into the nozzle inlet of the MiniJet housing.
This plug is also used for winterizing, so do not
discard.
Store the brass jets, the MiniJet housing cover, the
3/8” plug and the four screws for pool start-up.
Prevent dirt and debris from entering the plumbing
lines during construction.
Installing The MiniJet
1. Position the Layout Template to line up with the
vertical center line and mean water level. Tape it to
the pool wall.
2. Use a 1/4” bit to drill fourteen (14) mounting holes.
3. Use a 3/8” bit to drill the four (4) corner holes used
as guides for cutting out the center square.
4. Use a jigsaw and blade compatible with the
material of the pool wall to cut out the center
square, cutting around the outer edges of the four
(4) holes.
5. Insert the MiniJet housing through the wall from
the water side. Rest the back of the housing flange
against the inside of the pool wall.
6. Position the rear mounting plate over the back of
the MiniJet housing on the outside of the pool wall.
Insert the two (2) pan-head screws in the center
holes (top and bottom) of the flange, through the
pool wall and into the rear mounting plate. Secure
housing to pool wall.
MiniJet® for Vinyl Liner
Pool Installation
Plumbing The MiniJet
Water flow and pressure control the projection of the
water. As a rule, 4.4 GPM per nozzle will provide
adequate water flow. Refer to data below.
MiniJet Performance Data Chart
Height of
Jet Spray 3.3’ 6.6’ 9.8’ 13.1’
Feet
of Head 3.9’ 7.9’ 11.9’ 16.0’
GPM 2.1 3.0 3.7 4.4
1. Determine the size of the manifold or plumbing
loop and return pipe required.
MiniJet Pipe Sizing
Max.
MiniJets
Return
Pipe Sizing
Suction
Pipe Size
8 1-1/2” 1-1/2”
12 2” 2”
16 2-1/2” 2-1/2
26 3” 3”
2. Use 1/2” PVC pipe to connect the MiniJet to the
manifold or plumbing loop. See plumbing diagram
below.
Optional
Loop
Extend Past Last
MiniJet 5' Minimum
MiniJet
Manifold Pipe
Valve
Riser
From
Pump
See Chart for
Proper Sizing
3. When the MiniJets are lined up to project water
streams of equal distance, cut the riser to equal
lengths. When the MiniJets are not set in lines
parallel to the pool ledge, valve each MiniJet
separately.
4. Keep the 1/2” feed pipe short, and the manifold or
plumbing loop as close to the beam as possible.
Avoid undue stress on plumbing lines.
5. The manifold pipe should extend 5 ft. past the last
MiniJet®.
6. Pressure test the MiniJet.
7. After the liner is installed, place the gasket between
the front plate and the liner. Attach the front plate,
tightening each screw a little at a time to seat the
liner and gasket.
8. With a sharp knife, cut out the center 3” square of
the vinyl liner.
Pool Startup
1. Clean the pool water.
2. Remove threaded plug from the MiniJet housing.
Save plug for winterizing. Run water through the
MiniJet plumbing to clear lines.
3. Screw the brass jets into the threaded fittings.
Adjust nozzle alignment and plumbing valves until
the desired projection is reached.
4. Install MiniJet housing cover.
Winterizing
1. Drain all water from the MiniJet plumbing.
2. Screw the 3/8” plug provided into the nozzle inlet of
the MiniJet housing to protect the unit.
REAR
MOUNTING
PLATE
MINIJET
HOUSING
POOL PANEL
VINYL LINER FRONT
PLATE
MINIJET
HOUSING
COVER
HOUSING
FLANGE
GASKET
FRONT VIEW
AFTER INSTALLATION
© 2014 Zodiac Pool Systems, Inc. All rights reserved. Polaris® and the Polaris 3-wheeled
cleaner design are registered trademarks of Zodiac Pool Systems, Inc.
All other trademarks referenced herein are the property of their respective owners.
TL-1102 Rev A
Zodiac Pool Systems, Inc.
2620 Commerce Way, Vista, CA 92081
1.800.822.7933 | www.polarispool.com
MiniJet® for Vinyl Liner Pools
(FFMJ-VL)
LAYOUT TEMPLATE
CENTER LINE
Cut Along Dotted Line
TOP
1/4" Holes (14Pls)
CENTER LINE
3/8" Holes (4 Pls)
MEAN WATER LEVEL
3-5/16"
3-5/16"
© 2014 Zodiac Pool Systems, Inc. All rights reserved. Polaris® and the Polaris 3-wheeled
cleaner design are registered trademarks of Zodiac Pool Systems, Inc.
All other trademarks referenced herein are the property of their respective owners.
TL-1102 Rev A
Zodiac Pool Systems, Inc.
2620 Commerce Way, Vista, CA 92081
1.800.822.7933 | www.polarispool.com


Produktspezifikationen

Marke: JANDY
Kategorie: Nicht kategorisiert
Modell: MiniJet

Brauchst du Hilfe?

Wenn Sie Hilfe mit JANDY MiniJet benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert JANDY

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-