Jabsco 29120-2000 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Jabsco 29120-2000 (5 Seiten) in der Kategorie Toilette. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/5
Models 29090-2000
29120-2000
MANUAL MARINE TOILET
FEATURES
• Easy to clean white ceramic bowl
• Sturdy wood seat with durable baked enamel finish
• Forward angled pump for easy operation
• Convenient top-mounted dry bowl selector
• Reversible pump mounting for right or left hand
installation
• External seal housing/rod guide for easy replacement
• Extra large seal housing allows piston rod assembly to
be removed without removing valve cover
• Smooth external surfaces with skirted base to maintain
cleanliness
• Base of pump and valve cover are skirted to conceal
gasket/flap valves
• Triadic full-flow joker valve to avoid accidental blockage
• Multi-angle discharge port for versatility of plumbing
connection
VARIATIONS AVAILABLE
MODEL NO. DESCRIPTION
29090-2000 Compact Size Bowl & Seat
29120-2000 Household Size Bowl & Seat
SPECIFICATIONS
Inlet port – 3/4"
Disharge port – 1-1/2"
Weight – compact bowl: 26 lb
large bowl: 32 lb
APPLICATION
The Jabsco Manual toilet is designed to meet the require-
ments of onboard marine applications. It may be installed
above or below the waterline. If the toilet is, or can be,
below the waterline at any normal (including static) attitude
of vessel heel and/or trim, a 3/4" Vented Loop Fitting must
be installed in a length of hose that connects the flushing
pump to the rear of the bowl. The vented Loop Fitting
should be positioned so it remains about eight inches or
more above the waterline at all angles of heel and trim. If
the toilet is plumbed to an overboard discharge, the
discharge hose must also include a Vented Loop Fitting.
(See WARNING.) The toilet may be plumbed so waste is
Models 29090-2000 & 29120-2000
discharged to holding tank, directly overboard (where
permitted by law) or into a certified waste treatment device.
For installation versatility, the pump assembly may be
positioned on the left or right hand side of the bowl. Its
multi-angle discharge port will allow routing of discharge
hose in almost any direction for ease of installation and
neat appearance.
The toilet is available with either a compact china bowl to fit
restrictive areas or a large bowl with household size seat
assembly for maximum comfort. Its forward angled double
action pump with convenient top mounted dry bowl selector
is easy and natural to operate. It is self-priming with a dry
suction lift of up to 3 feet (1 meter) and a discharge head to
9 feet (3 meters). A full-flow triadic joker valve resists
blockage while providing positive back-flow prevention.
OPERATION
Manual Marine toilets have traditionally been somewhat
cumbersome and confusing to operate and maintain. The
Jabsco toilet has been designed with user convenience in
mind. The pump assembly is angled forward to provide a
natural, smooth stroke action. It has a top mounted wet/dry
bowl selector which can be operated with the same hand
used for pumping without releasing the pump handle.
The Jabsco toilet is surprisingly easy to operate. Simply
move the wet/dry bowl selector to the wet bowl position
(left) and pump handle up and down a few times to add
some water to the bowl prior to use. After using, flush by
again pumping handle up and down (in wet bowl position)
until bowl is thoroughly rinsed and evacuated. Then move
the wet/dry bowl selector to the dry bowl position (right)
and continue pumping until only about one cup of water
remains in the bottom of bowl. Leave the wet/dry bowl
selector in the dry bowl position when toilet is not in use.
Flood hazard. If toilet is installed below the
waterline or may be below the waterline at any
angle of heel or trim, it must be installed with
properly positioned vented loops. Failure to do
so can result in flooding which can cause loss
of property and life.
WARNING
!
Positioning and Mounting
The Jabsco Manual Toilet is assembled at the factory for
operation with the right hand. If preferred, or required by
available space, the pump and bowl may be rotated 180
degrees to provide left hand operation. To do this, remove
hose from inlet elbow (back of bowl) and rotate elbow 180
degrees. It may be necessary to remove the elbow, loosen
spud retaining nut and rotate the spud fitting so elbow will
be tight when pointing in the opposite direction. Remove,
rotate 180 degrees and reinstall both the bowl and pump
assembly. Reconnect hose to inlet elbow and the toilet is
ready for left hand operation.
The toilet must be installed on a well supported flat surface.
Ideally, if underside of mounting surface is accessible, the
toilet base should be through-bolted (using 5/16" bolts,
washers and locknuts) to the mounting surface. If the
underside of mounting surface is not accessible, the use of
5/16" lag bolts and washers is an acceptable alternative.
Before installing, position toilet in location to be installed.
Ensure there is adequate space around toilet to easily
operate pump and raise seat and lid to a fully opened
position. Seat and lid should swing open at least 110
degrees and be supported when open to avoid strain on
hinges. Ensure the base drain plug is accessible and inlet
and discharge hoses can be attached to their respective
ports without inducing significant lateral force. The
discharge elbow may be rotated (by loosening two flange
screws, rotating elbow and retightening screws) to accept
the most convenient routing of the discharge hose.
When proper installation has been established mark the
four base mounting holes on mounting surface and remove
toilet. Ensure that no wiring or plumbing is positioned under
the mounting surface which may be accidentally damaged
when the surface is drilled. Drill appropriate size holes for
fasteners being used. Mount toilet using flat washers
between head of bolts and plastic toilet base. If desired a
small bead of silicone or latex sealant may be applied
around base where it contacts the mounting surface to
prevent moisture from getting under the toilet base.
NOTICE: Do not use Polysulfide base sealants because
they may chemically attack the plastic which can result in
breakage.
Plumbing
Do not plumb the toilet to vessel’s
potable water supply. To do so can cause
water contamination that can cause illness or death.
If installing a new inlet thru-hull/seacock, ensure that it is
positioned on a part of the hull which is wetted at all
angles of heel or trim and free of water turbulence at any
hull speed. If discharging waste overboard (check legal
restrictions for overboard discharge), ensure discharge
thru-hull/seacock is both aft of and higher than the inlet
thru-hull/seacock. All inlet plumbing should be a
minimum of 3/4" ID and discharge plumbing a minimum
of 1-1/2" ID. All hose ends should be double clamped
with stainless steel hose clamps. If the toilet is above
waterline route hoses to seacocks, holding tank or
treatment device via a route as direct as possible.
However, for maximum sealing effect on the discharge
joker valve, it is recommended that the discharge hose is
looped upward about 8" above the discharge elbow
before it descends to its termination point. All bends and
elbows in plumbing should be kept to a minimum. It
should not be necessary to use any sealing compound
when attaching hoses to the inlet or discharge ports.
If the toilet is, or can be, below the waterline, at any normal
(including static) attitude of vessel heel and/or trim, a
3/4" vented loop must be installed in a length of hose
connecting the flushing pump to the rear of the bowl.The
vented loop fitting must be positioned 8" above the
waterline at all angles of heel and trim. To accomplish
this, remove the 3/4" hose supplied with toilet and
replace with a new length of hose long enough to properly
position the vented loop. If the toilet is plumbed for over-
board discharge, a 1-1/2" vented loop must be installed
in the discharge hose.The waste vented loop fitting must
also be positioned 8" above the waterline at all angles of
heel and/or trim and ideally should be located as close
to the toilet as practical. (See WARNING.)
If unfamiliar with proper plumbing requirements for
marine toilets, it is recommended that a qualified marine
plumbing technician is contacted to do the installation.
Flood hazard. If toilet is installed below the
waterline or may be below the waterline at any
angle of heel or trim, it must be installed with
properly positioned vented loops. Failure to do
so can result in flooding which can cause loss
of property and life.
WARNING
!
WARNING
!Flood hazard. Close inlet and outlet seacocks
prior to disassembling toilet. Failure to do so
can result in flooding which can cause loss of
property and life.
Toilet below
the waterline
WARNING
!
Maintenance
Periodic maintenance is generally not required other
than periodic cleaning and lubricating with Rule®brand
toilet cleaner and conditioner. To winterize toilet, operate
the pump in the dry bowl mode to evacuate as much
water as possible. Drain the remaining water from the
base by removing the base plug or sponge from bottom
of bowl. If charging the holding tank with anti-freeze by
pumping it through the toilet, use only ethylene glycol
based anti-freeze. To use petroleum based anti-freeze
can cause damage to the internal rubber toilet parts.
Service
Before performing any service, flush the toilet long enough
to ensure all waste is flushed from the discharge hose.
Close both inlet and discharge (if applicable) seacocks and
put a “DO NOT OPEN” notice on each to guard against
accidental opening and flooding while service is being per-
formed.
SEAL REPLACEMENT - Lift handle and wrap rod with
one turn of tape just under the handle. Gently grasp piston
rod (on tape) with pliers and unscrew handle. HOLD
PISTON ROD AT ALL TIMES OR IT MAY DROP DOWN
INTO PUMP. Remove bumper washer and unscrew and
remove seal/rod guide assembly. Wrap threads of piston
rod with one turn of tape to protect new seal and install
new seal/rod guide assembly. Remove tape from threads
and reinstall bumper washer and handle. Tighten handle
snugly (do not overtighten) and remove remaining tape.
MAJOR OVERHAUL - Loosen hose clamps on inlet
hose and remove it from the pump. Remove bowl link
hose from rear of pump assembly. Remove the two
screws that secure the discharge flange and elbow.
Remove the four screws that secure the pump to the
base and remove pump assembly.
The discharge joker valve and base valve/gasket can
now be removed. Remove the six screws that secure the
top valve cover, move the wet/dry bowl selector to the
wet bowl position and remove valve cover and piston rod
assembly from pump cylinder, taking care not to lose the
flap valve seating spring on the underside of the cover.
Remove top valve/gasket assembly and valve seat.
Remove piston O-Ring and seal/rod guide assembly
(see Seal Replacement instructions.). Clean all parts
and inspect for damage. Ensure pump cylinder wall is
not badly grooved or worn.
Install new seal/rod guide assembly (see Seal
Replacement instructions). Install new piston O-Ring.
Lubricate bore of pump cylinder with petroleum jelly.
Position valve seat and top valve/gasket assembly on
top of cylinder. Ensure the flap valve seating spring is
pushed securely on its locator post on the underside of
the valve cover. With the wet/dry bowl selector in the wet
bowl position, insert piston into cylinder bore and position
valve cover on top of cylinder. Secure with six screws.
Install joker valve in discharge elbow and base
valve/gasket assembly on base. Position discharge
flange and elbow on pump and secure with two screws.
Position pump assembly on base and secure with four
screws. Reattach bowl link hose to pump. Reattach inlet
hose to pump and secure with clamps.
BOWL SEAL REPLACEMENT - To replace the bowl seal
(base O-Ring) disconnect inlet and discharge hoses and
remove toilet from its mounting surface. Pry nut caps
from bowl fasteners. Invert toilet and hold bolts on under-
side of base while removing nuts and washers. Lift base
from bowl and remove O-Ring. Install new O-Ring, posi-
tion base on bowl and secure with fasteners ensuring plas-
tic washers are sandwiched between S. S. flat washers
and ceramic bowl. Invert toilet and snap plastic nut caps
onto nuts. Reinstall toilet on mounting surface, connect
hoses and secure with hose clamps.
Produktspezifikationen
| Marke: | Jabsco |
| Kategorie: | Toilette |
| Modell: | 29120-2000 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Jabsco 29120-2000 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Toilette Jabsco
25 Juli 2024
22 Januar 2024
Bedienungsanleitung Toilette
- Toilette Sanyo
- Toilette Philips
- Toilette Camry
- Toilette IKEA
- Toilette Coleman
- Toilette Dometic
- Toilette Rocktrail
- Toilette Haier
- Toilette Fiamma
- Toilette Easy Home
- Toilette Kohler
- Toilette Thetford
- Toilette Vetus
- Toilette Campingaz
- Toilette Miomare
- Toilette Gustavsberg
- Toilette Sanibroyeur
- Toilette Villeroy And Boch
- Toilette Duravit
- Toilette Pressalit
- Toilette Schütte
- Toilette Tiger
- Toilette AXA
- Toilette Kogan
- Toilette Enders
- Toilette SereneLife
- Toilette Geberit
- Toilette Ridgid
- Toilette PolyJohn
- Toilette Summer Infant
- Toilette Sloan
- Toilette Satellite
- Toilette CurAqua
- Toilette Barumi
- Toilette Fienza
- Toilette MCombo
- Toilette TMC
- Toilette TOTO
- Toilette Sunwind
- Toilette Stimex
- Toilette Caroma
Neueste Bedienungsanleitung für -Kategorien-
4 Oktober 2024
1 Oktober 2024
1 Oktober 2024
30 September 2024
24 September 2024
10 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024