Intermec ScanPlus 1802 Bedienungsanleitung
Intermec
Barcode-Lesegeräte
ScanPlus 1802
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Intermec ScanPlus 1802 (4 Seiten) in der Kategorie Barcode-Lesegeräte. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
Operator's Guide
ScanPlus 1802
Vista Cordless
System
0 cm - 33 cm
(0" - 13")
0
25 m (80 ft)
2 3
PDF417 codes
One-dimensional codes
Operation
The ScanPlus 1802 Vista Cordless System consists of a base station (MicroBar 9735) and at least
one scanner (ScanPlus 1802 VT PDF).
"beep"
7.5 cm (3")
PDF417 ideal reading distance
Reading distance
Range
"beep beep beep beep beep beep"
"beep"
4 5
➊
➋
➌
WARNING: Fire, explosion and severe burn hazard. Do not crush, disassemble, heat above
212° F (100° C) or incinerate Battery Pack (P/N 3-360029-03).
Low battery Regulatory statements
Intermec hereby declares that the ScanPlus 1802 Vista Cordless System has been tested and found com-
pliant with the below listed stan dards as required by the R&TTE Directive 99/05/EC: ETS 301 489, EN 300
220-1, EN 60950 and EN 60825-1. This device is TÜV GS licensed (EN 60950 and EN 60825-1). The original
Declaration of Conformity is available on demand. The ScanPlus 1802 Vista Cordless System is certifi ed for use in all countries
belonging to the European Union.
USA & Canada: This device complies with Part 15 of the FCC rules and RSS-210 of Industry Canada. Operation is subject
to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the
ins truc tions, it may cause harmful interference to radio com mu ni ca tions. However there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference, the user is encouraged to try
to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase
the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit diff erent from
that to which the receiver is connected or consult the dealer or an experienced radio/TV technician for help.
In order to maintain compliance with the FCC Rules, the I/O cables that interconnect between the device and any peripheral
must be as specifi ed by Intermec.
Caution: Changes or modifi cations not expressly approved by Intermec could void the user's authority to operate this
equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. This
device requires a radio license unless it is used totally inside a building (the user must obtain this license).
This device complies with the UL standards (UL1950 / C22.2 n°950).
Cet ap pa reil nu mé ri que de la classe B respecte toutes les exigences du Règlement sur le ma té riel brouilleur du Canada.
Cet appareil exige une license radio à moins d'être entièrement installé dans un batiment (l'utilisateur doit obtenir cette
license).
Cet équipement est conforme aux exigences de CNR-210 de Industrie Canada. L'utilisation de ce dispositif est autorisée aux
conditions suivantes: (1) Il ne doit pas produire de brouillage, et (2) l'utilisateur de l'équipement doit accepter tout brouillage
reçu, même si ce brouillage est susceptible de compromettre son fonctionnement.
Cet équipement est conforme aux normes UL (UL1950 / C22.2 n°950).
Australia-New Zealand: This equipment has been tested and found to conform to the Australian EMC fra-
mework concerning Class B digital devices, prescribed by the Australian/New-Zealand standard AS/NZS 3548.
The information contained in this document is for informational purposes only and is subject to change without notice.
No part of this document may be copied or reproduced in any manner without the prior written per mis sion of Intermec
Technologies Corporation.
ScanPlus/MicroBar products are covered by patents issued or pending in the USA and other countries.
The word Intermec, the Intermec logo, ScanPlus, MicroBar and EasySet are either trademarks or registered trademarks of
Intermec.
Throughout this document, trademarked names may be used. Rather than put a trademark (™ or ®) symbol in every occur-
rence of a trademarked name, we state that we are using the names only in an editorial fashion, and to the benefi t of the
trademark owner, with no intention of infringement.
Class 1 LED product - safe when used in any reasonable operating conditions.
N309
Produktspezifikationen
| Marke: | Intermec |
| Kategorie: | Barcode-Lesegeräte |
| Modell: | ScanPlus 1802 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Intermec ScanPlus 1802 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Barcode-Lesegeräte Intermec
10 August 2024
Andere Handbücher Intermec
25 August 2024
23 August 2024
23 August 2024
22 August 2024
22 August 2024
22 August 2024
10 August 2024
2 August 2024
31 Juli 2024