Intelix AVO-VGA Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Intelix AVO-VGA (4 Seiten) in der Kategorie Schalten. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
Intelix AVO-VGA
Installation Manual
Introduction
The Intelix AVO-VGA balun set transmits VGA video passively over standard unshielded
twisted pair cable, such as Cat 5, Cat 5e or Cat 6. The AVO-VGA eliminates costly and
bulky VGA cable, and extends video transmission distances.
Pre-Installation
The AVO-VGA features shielded RJ45 connectors, which are provided as an option in
harsh electrical environments, such as installations with large motors or cable runs
near sources of interference. In such environments, shielded twisted pair cable (STP) may
provide additional noise immunity. When using STP, ensure the shield on both ends of the
cable run is terminated to a shielded RJ45 connector.
Note: The AVO-VGA does not support VGA handshakin
g
and control si
g
nals.
Therefore, it is necessar
y
to set the monitor attributes prior to installin
g
the balun set.
First connect the source (typically a computer) directly to the destination (typically a
monitor) with a standard VGA cable. After doin
g
so, set the monitor attributes to the
required settin
g
s (i.e., resolution, color, etc.). For best results, also set the contrast and
b
ri
g
htness to the maximum level.
Caution: Do not attempt to disassemble or alter the balun housin
g
. There are no
user-serviceable parts inside the unit. Doing so will void your warranty.
Installation
1. Power off the source and destination devices which will be connected to the baluns.
2. Verify the modular outlets and cross connects to which you will connect the AVO-
VGA are configured properly and labeled appropriately to identify the circuit.
3. Verify the desired twisted pairs are not being used for other LAN or telephone
equipment.
4. Connect the send balun (AVO-VGA-S) to the VGA port of the source equipment.
Tighten the mounting screws on each balun.
5. Connect one end of the twisted pair cable to the send balun. The RJ45 pinout in the
twisted pair cabling should conform to the EIA/TIA 568A or 568B standard.
6. Connect the receive balun (AVO-VGA-R) to the destination equipment.
7. Connect the other end of the twisted pair cable to the receive balun. The RJ45 pinout
in the twisted pair cabling should conform to the EIA/TIA 568A or 568B standard.
8. Power on the source and destination equipment.
9. If necessary, set monitor contrast and brightness to the desired levels.
10. Set the monitor refresh rate to the optimal rate for the display at the desired resolution.
11. If necessary, adjust the image quality with the Sync Adjust switch on the send and
receive baluns. It is recommended that both switches be in the same position.
Caution: Do not connect the balun to a telecommunication outlet wired to
unrelated equipment. Doin
g
so ma
y
dama
g
e the unit or an
y
connected equipment.
Ensure all connected twisted pair cabling is straight-through (point-to-point).
Caution: To minimize the possibilit
y
of equipment dama
g
e from electrostatic
discharge (ESD), all source and destination equipment must be powered off durin
g
installation. This includes signal extenders, splitters, and switches.
Note: For your convenience, it is recommended that
y
ou uniquel
y
mark the ends
of the twisted pair cable before pulling them through a wall or conduit.
Note: The AVO-VGA features an optional grounding screw that may be used to
correct an
y
ima
g
e anomalies, such as differences in hue from one side of a monitor to
the next. Should this occur, connect the balun
g
round to earth
g
round. However, if the
building has a grounding problem, such as ground loo
p
s,
g
roundin
g
the balun ma
y
negatively affect the signal. Only ground the AVO-VGA if it positivel
y
affects the
si
g
nal.
Troubleshooting
Symptom Probable Causes Possible Solutions
Change the screen refresh rate of the video
source to the next higher or lower setting
Image distorted or
skewed
Adjust the Sync Adjust switch on both the send
and receive baluns
No image
Weak or distorted
sync signal
Attach or detach the grounding screw on either
or both of the baluns to earth ground
Reversed polarity Unusual colors
Bad RJ45 crimp
Verify RJ45 pinout conforms to EIA/TIA 568A
or 568B standard. If not, re-crimp the cable.
Verify cable grade and total cabling distance
Reduce the screen resolution
Smearing or weak
video contrast
Exceeded cable
distance
Reduce the screen refresh rate
Attach or detach the grounding screw on either
or both of the baluns to earth ground
Horizontal bars
moving upward in
background Verify the source and destination equipment are
at the same ground potential.
Shaking image
Ground loop
problem
Change the screen refresh rate of the video
source to the next higher or lower setting
Background pattern EMI interference Identify possible radiating frequency sources and
isolate them from the cabling. Use shielded
twisted pair cabling.
Produktspezifikationen
| Marke: | Intelix |
| Kategorie: | Schalten |
| Modell: | AVO-VGA |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Intelix AVO-VGA benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Schalten Intelix
25 Juli 2024
Bedienungsanleitung Schalten
- Schalten Asus
- Schalten Belkin
- Schalten Hama
- Schalten HP
- Schalten LogiLink
- Schalten Manhattan
- Schalten Nedis
- Schalten Philips
- Schalten SilverCrest
- Schalten Panasonic
- Schalten Brennenstuhl
- Schalten Clas Ohlson
- Schalten Cotech
- Schalten Profile
- Schalten ZyXEL
- Schalten Bosch
- Schalten Yamaha
- Schalten Powerfix
- Schalten CSL
- Schalten Eminent
- Schalten Linksys
- Schalten Netgear
- Schalten König
- Schalten PCE
- Schalten Renkforce
- Schalten Trotec
- Schalten Schneider
- Schalten Rex
- Schalten Kaiser
- Schalten Vivanco
- Schalten Abus
- Schalten Elro
- Schalten Smartwares
- Schalten Tesla
- Schalten Perel
- Schalten Nexa
- Schalten Tork
- Schalten GEV
- Schalten Goobay
- Schalten Lindy
- Schalten Tripp Lite
- Schalten Ansmann
- Schalten Mercusys
- Schalten Marmitek
- Schalten Honeywell
- Schalten TRENDnet
- Schalten TP-Link
- Schalten Kathrein
- Schalten Flamingo
- Schalten Alcatel
- Schalten Tiptel
- Schalten Black Box
- Schalten Alpine
- Schalten Techly
- Schalten Ebode
- Schalten Theben
- Schalten Vacmaster
- Schalten GAO
- Schalten Hager
- Schalten Behringer
- Schalten Omnitronic
- Schalten Monoprice
- Schalten Ecler
- Schalten Monacor
- Schalten Huawei
- Schalten JUNG
- Schalten Victron Energy
- Schalten Ei Electronics
- Schalten Edimax
- Schalten Totolink
- Schalten D-Link
- Schalten Sylvania
- Schalten Audiovox
- Schalten B-Tech
- Schalten QNAP
- Schalten SPC
- Schalten Speaka
- Schalten Digitus
- Schalten Sygonix
- Schalten DataVideo
- Schalten Lancom
- Schalten LevelOne
- Schalten Merten
- Schalten APC
- Schalten Eberle
- Schalten Cisco
- Schalten Delta Dore
- Schalten Grässlin
- Schalten Tenda
- Schalten CyberPower
- Schalten Boss
- Schalten IFM
- Schalten Intertechno
- Schalten Elation
- Schalten Ubiquiti Networks
- Schalten Kramer
- Schalten Aeon Labs
- Schalten Intellinet
- Schalten Eaton
- Schalten AV:link
- Schalten Hikvision
- Schalten Vemer
- Schalten PreSonus
- Schalten Planet
- Schalten EnGenius
- Schalten Finder
- Schalten Mikrotik
- Schalten Shimano
- Schalten Homematic IP
- Schalten Berker
- Schalten Dormakaba
- Schalten Emerson
- Schalten Generac
- Schalten Intermatic
- Schalten KlikaanKlikuit
- Schalten Mercury
- Schalten Paladin
- Schalten Provision ISR
- Schalten Robbe
- Schalten SEC24
- Schalten Steren
- Schalten Suevia
- Schalten AMX
- Schalten Triax
- Schalten WHALE
- Schalten Vimar
- Schalten Cudy
- Schalten Siig
- Schalten Electro Harmonix
- Schalten RGBlink
- Schalten Iogear
- Schalten StarTech.com
- Schalten Smart-AVI
- Schalten Dahua Technology
- Schalten PAC
- Schalten Gefen
- Schalten Avocent
- Schalten Legrand
- Schalten Atlantis Land
- Schalten CYP
- Schalten H-Tronic
- Schalten ATen
- Schalten Axing
- Schalten KanexPro
- Schalten SmartAVI
- Schalten Advantech
- Schalten Kraus & Naimer
- Schalten Chacon
- Schalten Juniper
- Schalten Fibaro
- Schalten Phoenix Contact
- Schalten Audac
- Schalten OSD Audio
- Schalten Wentronic
- Schalten SunBriteTV
- Schalten BZBGear
- Schalten Crestron
- Schalten Kemo
- Schalten ORNO
- Schalten Extron
- Schalten Atlona
- Schalten Equip
- Schalten Heitronic
- Schalten Hamlet
- Schalten STI
- Schalten Matrox
- Schalten Blustream
- Schalten Vivolink
- Schalten Mach Power
- Schalten Ernitec
- Schalten Cambium Networks
- Schalten ConnectPro
- Schalten Micro Connect
- Schalten ICasa
- Schalten Maclean Energy
- Schalten Cooking Performance Group
- Schalten Flic
- Schalten Liberty
- Schalten Noark
- Schalten 2USB
- Schalten KVM-TEC
- Schalten Setti+
- Schalten PureLink
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
12 Oktober 2024
11 Oktober 2024
8 Oktober 2024
8 Oktober 2024
5 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
3 Oktober 2024