IFi Audio GO bar Bedienungsanleitung

IFi Audio Empfänger GO bar

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für IFi Audio GO bar (1 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/1
ifi-audio.com Ver1.2
Thank you for purchasing the bar from the GO series. The bar is a
balanced USB audio DAC amplifier.
1. Audio format, frequency and sound effects LED
The LED colour scheme indicates the current sampling frequency
and audio format received by the GO bar from the music source.
Sound effect modes are also indicated.
LED Mode
White 44.1/48kHz
White 88.2/96kHz
White 176.4/192kH z
White 352.8/384kH z
White DSD 64/128
White DSD 256
Sound effects
LED Status
Blue XSpace
+
Orange XBass
Tip: Sonically-hindering DSP is NOT used for XBass+ nor XSpace systems. They use the
highest-quality discrete components and operate purely in the analogue domain. Hence
all the clarity and resolution of the original music is retained.
2. MQA and Digital filter LED
MQA:
Green MQA
Blue MQA Studio
Magenta Original Sample Rate*
*MQB
Digital Filter for PCM Playback:
LED Mode
Cyan BP
White GTO
Red STD
Yellow MIN
Off DSD playback
1
Specications
input: USB-C
Formats: PCM 384kHz
DSD 256
DXD 384kHz
MQA Full Decoder
DAC: Bit-Per fect DSD & DXD DAC by Cirrus Logic
Headphone Outputs:
Balanced: 4.4mm
UnBAL: 3.5mm
Power Output:
Balanced: 475mW@32Ω; 7.2V@600Ω
UnBAL: 300mW@32Ω; 3.8V@600Ω
Output Impedance:*
Balanced: <1Ω
UnBAL: <1Ω
SNR:
Balanced: 132dBA
UnBAL: 108dBA
DNR:
Balanced: 109dB(A)
UnBAL: 108dB(A)
THD + N:
Balanced: <0.002% (6.5mW/2.0V @ 600Ω)
UnBAL: <0.09% (100mW/1.27V @ 16Ω)
Frequency Response: 20Hz - 45kHz (-3dB)
Power Consumption: <4W max.
Dimensions: 65 x 22 x 13.2 mm (2.6" x 0.9" x 0.5”)
Net weight: 28.5g (1.0 oz)
Limited Warranty: 12 months**
*With iEMatch engaged: ＜3.6Ω
**12 months typical or as permitted/required by local reseller laws.
***Specications are subject to change withou t notice.
2
The following 4 digital filters are available:
'BP' (Cyan) Bit-Perfect: no digital filtering, no pre or post
ringing
'STD' (Red) Standard, modest filtering, modest pre and
post ringing
'MIN' (Yellow) Minimum phase, slow roll-off, minimum pre
and post ringing
'GTO' (White) Gibbs Transient-Optimised: upsampled to
352/384kHz, minimum filtering, no pre
ringing, minimum post ringing
Note: If the GTO filter is selected, the only sample rate indicator showing will be
352.8/384kHz, indicating the upsampling operation of this filter.
3 4 5
4. Volume control and gain
To increase volume, press the + button, and to decrease it, press
the - button. Volume level is briefly displayed on the GO bar while
pressing one of the volume buttons, shown by the number of
white LEDs on at a time - from none to 6.
The increase or decrease of volume can be synchronised with the
volume of the mobile phone/computer. The connected device
will indicate a change of volume on its display if synchronisation
is on, and the device’s volume controls can additionally be used to
adjust volume. The GO bar’s volume buttons are still operational.
By default, the synchronisation feature is off. To switch this on or
off, press the settings button (5) for > 8s. On is indicated by the 6
white LEDs switching on in sequence from LED 1 and 6 to the
centre. Off is indicated by the 6 white LEDs switching off in the
opposite direction.
Turbo Mode increases the gain by 6dB. To switch this on or off,
press the + and - volume buttons together for ≥ 2s. Turbo Mode
on is indicated by 2 white LEDs increasing to 6 lighting up at the
same time for 2s. Normal gain is indicated by 6 white LEDs
diminishing to 2 lighting up for 2s.
Tip: For sensitive headphones and earphones, leave Turbo Mode off. For less sensitive
headphones, it may be appropriate to switch Turbo Mode on.
5. Settings and Digital filter mode
This button cycles between:
Off > XSpace > XBass+ > XSpace and XBass+ (short click). Please
refer to item 1 for sound effects LED indications.
Digital filter setting mode (long press ≥2s). Please see below.
Digital filter
To enter digital filter setting mode, press and hold the button for
≥3s. The MQA LED will flash with the currently set digital filter
colour (as shown in item 2). Press the + or - buttons (4) to change
the filter selection. A short press on the settings button (5) will
select and exit the filter setting mode.
3. iEMatch switch
iEMatch reduces the output level, so that even the most
sensitive In-Ear-Monitors (IEMs) can be matched to the GO bar.
= 3.5mm headphones
= off
= 4.4mm headphone
Tip: The GO bar and/or the headphone will not be damaged if the iEMatch switch is
adjusted incorrectly, but the attenuation level will not be correct.
iEMatch
off
3.5
4.4
6. S-Balanced 3.5mm headphone output
For connecting 3.5mm headphones. This is a single -ended
output.
7. Balanced 4.4mm headphone output
For connecting balanced 4.4mm headphones. This is a fully
balanced output.
8. USB-C input
The USB-C socket plays up to 32-bit 384kHz, has full MQA
decoding, and native DSD up to DSD256.
Tip: Because the Go bar is a high-performance gadge t and the iPhone's powe r supply is
conservative, we recommend using an iPhone 8 or higher for reliable connectivity, and the
battery should be charged to 70% or higher.
Warning: If the GO bar’s volume synchronisation function is on, and the music source is
Tidal via Windows, please ensure that the Tidal setting of Forced Volume is off. With this
function on, there is no volume control possible, and the volume will be at maximum. This
has the potential to damage the connecte d headphone and/or your hearing.
6 7
8

Produktspezifikationen

Marke: IFi Audio
Kategorie: Empfänger
Modell: GO bar

Brauchst du Hilfe?

Wenn Sie Hilfe mit IFi Audio GO bar benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Empfänger IFi Audio

IFi Audio

IFi Audio iCAN Phantom Bedienungsanleitung

28 August 2024
IFi Audio

IFi Audio Zen Can Signature 6XX Bedienungsanleitung

28 August 2024
IFi Audio

IFi Audio GO bar Bedienungsanleitung

20 August 2024
IFi Audio

IFi Audio Go blu Bedienungsanleitung

20 August 2024
IFi Audio

IFi Audio xCAN Bedienungsanleitung

19 August 2024
IFi Audio

IFi Audio UNO Bedienungsanleitung

19 August 2024
IFi Audio

IFi Audio Pro iCAN Signature Bedienungsanleitung

18 August 2024
IFi Audio

IFi Audio xDSD Gryphon Bedienungsanleitung

18 August 2024
IFi Audio

IFi Audio Pro iCAN Bedienungsanleitung

18 August 2024
IFi Audio

IFi Audio ZEN CAN Bedienungsanleitung

21 Juli 2024

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-

Rotel

Rotel RA‑1592MKII Bedienungsanleitung

16 Oktober 2024
Denon

Denon AVR-S900W Bedienungsanleitung

16 Oktober 2024
Pro-Ject

Pro-Ject Amp Box DS2 Bedienungsanleitung

15 Oktober 2024
AKG

AKG HP12U Bedienungsanleitung

15 Oktober 2024
Sennheiser

Sennheiser EM 9046 SU Bedienungsanleitung

14 Oktober 2024
Yamaha

Yamaha MusicCast RX-V481 Bedienungsanleitung

14 Oktober 2024
JL Audio

JL Audio VX600/6i Bedienungsanleitung

12 Oktober 2024
Pioneer

Pioneer SX-303RDS Bedienungsanleitung

10 Oktober 2024
Technics

Technics SA-160L Bedienungsanleitung

8 Oktober 2024
Avantree

Avantree Audiplex Bedienungsanleitung

7 Oktober 2024