Hunter BTT 101 Bedienungsanleitung

Hunter Besproeiingsbesturing BTT 101

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hunter BTT 101 (2 Seiten) in der Kategorie Besproeiingsbesturing. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

BTT

Battery-Operated

Bluetooth Tap Timer

Quick Start Guide

ENGLISH

Please read and keep all safety and use instructions. For more information,

visit hunterindustries.com/BTT.

Important Safety Instructions

1. Read, keep, and follow these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specied by the manufacturer.

4. Use a Hose Vacuum Breaker where required to prevent backow to the

water supply.

Bluetooth Information

1. Frequency band of operation: 2400MHz to 2480MHz.

2. Bluetooth: Maximum transit power less than 20 dBm EIRP

3. Bluetooth Low Energy: Maximum power spectral density less than

10 dBm/MHz EIRP

Warnings and Cautions

• Do NOT make unauthorized alterations to this product.

• Keep the product away from re and heat sources.

• Do not expose products containing batteries to excessive heat (e.g.,

from storage in direct sunlight, re, or the like).

• The product label is located on the back of the product.

• Replace only with same or equivalent battery type. Dispose of used

batteries according to instructions.

• Do NOT mix old and new batteries, or mix dierent types or makes

of batteries.

• Store batteries in a cool, dry place at normal

room temperature.

Connecting the Batteries

1. Squeeze the battery compartment tabs

with two ngers to withdraw the battery

compartment.

2. Insert the included 2x AA standard

alkaline batteries into the terminals.

Observe + position.

3. Replace the battery compartment.

4. Test power to the device by pressing the

5. manual button on the front of the device and

6. listen for a click sound. Press again to turn o.

7. NOTE: Manual button mode runs for a

maximum 60 minutes and then shuts o

watering.

Connecting to Water Supply BTT-100/200

Instructions:

1. Connect the device only to a standard

¾" (19 mm) threaded water supply/hose

faucet outlet.

2. Hand-tighten until secure.

3. Connect a ¾" (19 mm) inlet hose or drip

adapter (Model No. BTT-LOC) to the BTT

outlet.

4. Hand-tighten until secure.

Manual Button

Low Battery Indicator

Manual Button

Low Battery Indicator

Connecting to Water Supply

BTT-101/201 Instructions:

1. Connect the device only to a standard ¾" (19 mm) BSP-threaded water

supply/hose faucet outlet. Unscrew the grey adapter to use the 1"

(25 mm) NPT inlet option.

2. Hand-tighten until secure.

3. Connect a ¾" (19 mm) inlet hose, drip adapter (Model No. BTT-LOC) or

quick connect adapter (included) to the BTT outlet.

4. Hand-tighten until secure.

App Programming

1. Download the free Hunter BTT app to a

smartphone device from the App Store for

iOS devices, or Google Play™ store for

Android™ devices.

• iOS Compatibility: Requires iOS

9.0 or later. Compatible with

iPhone.

• Android Compatibility: Requires

Android 4.4 or above.

2. Be within 32' (10 m) of the timer.

3. Turn on Bluetooth on the

smartphone device.

4. Press the SCAN button and select

the BTT device.

Timer Mode Programming

Timer mode allows for watering at two

dierent start times from 1 minute to 6 hours,

per watering day.

1. the Schedule Icon and select the Pre

Timer tab.

2. Water Days: Select the desired water

days. Save and Conrm.

3. Start Times: Set START TIME 1 and

optional START TIME 2-4. Save and

Conrm.

4. Run Time: Set the desired RUN TIME from

1 second to 6 hours. Save and Conrm.

Cycling Mode Programming

Cycling mode allows the Run Time to repeat

continually aer the scheduled interval (Soak

Time) from a Start Time

to an End Time.

1. Press the Schedule Icon and select

the Cycling tab

2. Water Days: Select the desired

water days. Save and Conrm.

3. Start Times: Set START TIME 1

and optional START TIME 2.

Save and Conrm.

4. End Times: Set END TIME 1 and optional

END TIME 2. Save and Conrm.

5. Run Time: Set the desired RUN TIME from

1 second to 24 hours. Save and Conrm.

6. Soak Time: Set optional SOAK TIME, the

time between each Run Time, from 1

second to 24 hours. Save and Conrm.

Additional Settings

1. Press the Settings Icon

2. Renaming your BTT: Select Settings tab and

enter a name in Nickname section. Save and Conrm.

3. Creating a Passcode: In BTT Settings, enter a 4-digit code in the Create

a Passcode section. To disable, press Disable Passcode and Conrm.

4. Changing the Language: Select Settings

tab and press App Settings then

Language. Select the desired language.

Save and Conrm.

5. Suspend: Set optional RAIN DELAY from

0-99 days. Save and Conrm.

6. O Mode: To shut down Cycling Mode,

select the O tab and Conrm.

7. Zone O Mode: For Manual Irrigation,

select the Dashboard and press the play

button, set a value of 1-360 minutes.

Press Start and OK.

Troubleshooting

Problem Solution

Manual button press not

responding

Replace the batteries.

(2 AA alkaline batteries)

Device not appearing

in scan list or loses

connection

Move within 32' (10 m) of device.

Replace the batteries.

(2 AA alkaline batteries)

App indicates watering,

but none is occurring

Turn on water supply.

Reconnect device.

Automatic irrigation does

not start at start time

Verify that BTT is programmed for

automatic watering.

Correct AM/PM of start time.

Correct water days.

Device waters more than

one time

Eliminate device start times as needed.

Correct the Soak Time in Cycling mode.

Incorrect Passcode Remove and replace batteries.

Go back to the app and connect.

FCC Notice

This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the manufacturer’s

instruction manual, may cause interference with radio and television

reception. This equipment has been tested and found to comply with the

limits for a Class B digital device pursuant to Part 15 of the FCC Rules. This

device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

Notice: The FCC regulations provide that changes or modications not

expressly approved by Hunter Industries Inc. could void your authority to

operate this equipment. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

with radio or television reception, which can be determined by turning

the equipment o and on, you are encouraged to try to correct the

interference by one or more of the following measures:

• Reorient the receiving antenna.

• Relocate the system with respect to the receiver.

• Move the system away from the receiver.

• Plug the system into a dierent outlet so that the system

and the receiver are on dierent branch circuits.

• Consult the dealer or an experienced radio/TV technician

for help.

If necessary, consult a representative of Hunter Industries Inc. or an

experienced radio/television technician for additional suggestions.

Changes or modications not expressly approved by Hunter Industries

could void the user’s authority to operate this device.

Industry Canada Notice

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

CE Notice

Hunter Industries hereby declares that this product is in compliance with

the essential requirements and other relevant provisions of Directive

2014/53/EU and all other EU directive requirements.

This symbol means the product must not be discarded as household

waste, and should be delivered to an appropriate collection facility for

recycling. Proper disposal and recycling helps protect natural resources,

human health, and the environment. For more information on disposal

and recycling of this product, contact your local municipality, disposal

service, or the shop where you bought this product. Please dispose of used

batteries properly, following local regulations. Do NOT incinerate.

Management Regulation for Low-power Radio-frequency Devices

Article XII

According to “Management Regulation for Low-power Radio-frequency

Devices” without permission granted by the NCC, any company,

enterprise, or user is not allowed to change frequency, enhance

transmitting power or alter original characteristic as well as performance

to approved low-power radio frequency devices.

Article XIV

The low power radio-frequency devices shall not inuence aircra

security and interfere legal communications; if found, the user shall cease

operating immediately until no interference is achieved. The said legal

communications means radio communications operated in compliance

with the Telecommunications Act.

Equipment Protection

• Water pressure requirements: Make sure your water pressure

is 7116 PSI (0.5–8 Bar)

• Make sure water is clean and particle-free.

• Maximum inlet water temperature: 100°F (38°C)

• Operating temperature: 41°F to 140°F (5°C to 60°C)

• Protect against freezing: Do not allow water to freeze in the

Tap Timer or in any connected hose.

• Chemicals: Do not use the Tap Timer with or to dispense

any chemicals of any kind.

• Do not open: The Tap Timer requires no maintenance and contains no

user-serviceable parts.

• Periodic inspection of connections is recommended to

prevent water leaks.

• Approvals: IPX6

The Bluetooth word mark and logos are registered trademarks owned by Bluetooth

SIG, Inc. and any use of such marks by Hunter Industries Corporation is under license.

IOS is a trademark or registered trademark of Cisco in the U.S. and other countries

and is used under license.

Apple,the Apple logo, and iPhone are trademarks of Apple Inc., registered in the U.S.

and other countries.

App Store is a service mark of Apple Inc. Google, the Google logo, Google Play, and

Android are trademarks of Google LLC.

Industries, registered in the U.S. and other countries.

hunterindustries.com RC-074-QG-BTT B EN 5/19

http://hunter.direct/btthelp

Produktspezifikationen

Marke:	Hunter
Kategorie:	Besproeiingsbesturing
Modell:	BTT 101

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hunter BTT 101 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Besproeiingsbesturing Hunter

Hunter BTT 101 Bedienungsanleitung

16 August 2024

Bedienungsanleitung Besproeiingsbesturing

Neueste Bedienungsanleitung für -Kategorien-

Florabest HG03453B Bedienungsanleitung

8 Oktober 2024

Vonroc WT502DC Bedienungsanleitung

6 September 2024

Vonroc PS505XX Bedienungsanleitung

6 September 2024

Brandson 306810 Bedienungsanleitung

4 September 2024

Claber Video-2 Plus 8419 Bedienungsanleitung

3 September 2024

Claber Tempo Hybrid 8488 Bedienungsanleitung

3 September 2024

Claber Video-2 8480 Bedienungsanleitung

3 September 2024

Claber Select 8425 Bedienungsanleitung

3 September 2024

Claber Tempo myAquaSolar 8498 Bedienungsanleitung

3 September 2024

Claber Pratico 8428 Bedienungsanleitung

3 September 2024