Humminbird 300TX Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Humminbird 300TX (28 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 37 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/28
offered by Busse-Yachtshop.com
offered by Busse-Yachtshop.com
INSTALLATION PREPARATION
PARTS SUPPLIED
PARTS SUPPLIED
Before installing your new Humminbird fishfinder, please ensure the following parts are
included in the box:
• Fishfinder
• Transducer with 20’ (6m) of cable and mounting hardware kit
• Mounting system and mounting hardware kit
• 6’ (2m) power cable
• Publications kit
It any of these items is missing, call our Customer Support Hotline.
ACCESSORIES
Humminbird offers a wide assortment of accessories that complement and expand the
capability of your new fishfinder. These accessories are designed with the same high
standards and are backed by the same one-year warranty. The Humminbird Accessory
catalog included with your unit contains descriptions of the many accessories available
and ordering information. All Humminbird accessories are available through your full-
service Humminbird dealer or factory direct through our number listed in the Customer
Support section.
INSTALLATION OVERVIEW
Your Humminbird fishfinder consists of two primary components to install: the control
head and the transducer.
The control head contains the sonar transmit and receive circuitry, as well as the user
controls and display. It should be installed in a location that provides access to the
controls and visibility while in use. The control head mounts on a quick disconnect
mounting system that swivels and tilts providing flexibility for viewing from almost
anywhere on the boat.
The transducer converts electrical energy from the transmitter into mechanical pulses or
sound waves. The transducer also receives the reflected sound waves and converts
them back into electrical signals for display on the control head. It should be installed in
contact with the surface of the water in an area that has smooth waterflow- usually on
the transom of the boat. There are several mounting options for the transducer. Review
the following section to determine the method that works for you and your boat.
offered by Busse-Yachtshop.com
INSTALLATION PREPARATION
INSTALLATION OVERVIEW
Determining How to Mount the Transducer
Your Humminbird fishfinder includes a standard
transducer. This transducer can be mounted on the
transom of the boat or bonded to the inside of a fiberglass
hull boat.
The transom installation, which is the most widely used,
places the transducer on the outside of the boat hull. This
technique produces the least signal loss, and provides a
way to adjust the transducer after installation. The
mounting hardware included is designed to protect both
the boat and the transducer should the boat strike debris in
the water or when trailering.
As an alternative to transom mounting, it is possible on many
fiberglass-hulled boats to glue the transducer on the inside of
the boat hull. Since fiberglass has similar sonar
characteristics as water, the sonar signal can pass through
the boat hull with minimal loss. The hull of the boat must be
single layer construction (not double-hulled) Also, any air
trapped in the lamination of the fiberglass would prevent the
sonar signal from passing through.
Inside the hull installations require no holes be drilled into the
boat and through experimentation, high-speed operation
comparable to transom mounting can be achieved. Two-part slow cure epoxy (not
included) is required to glue the transducer in place.


Produktspezifikationen

Marke: Humminbird
Kategorie: Nicht kategorisiert
Modell: 300TX

Brauchst du Hilfe?

Wenn Sie Hilfe mit Humminbird 300TX benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Humminbird

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-