HQ TVS--FSB07B Bedienungsanleitung

HQ Tv-meubel TVS--FSB07B

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr HQ TVS--FSB07B (4 Seiten) in der Kategorie Tv-meubel. Dieser Bedienungsanleitung war fĂĽr 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
INSTALLATION INSTRUCTIONS
Max Load Capacity: 30kg(66lbs)
30kg
(66lbs)
MAX
Pitching angle:
-20° ~ +20°
Swivel: 180°
M
LCD Wall Mount
7
Maintenance
Once you have mounted the bracket and the flat screen, check that they are sufficiently secure and safe to
use. You should check whether screws are fixed well each two months. If you have any doubts regarding the
installation, please consult our retailer or service department for detail.
Pitching angle adjustment
• Use the tilt adjusting knob to adjust your TV to the desired angle, the pitching angle can be adjusted
between -20°~20°, as shown in fig 5.1.
5
fig. 5.1
wall
wall
Tilt adjusting knob
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin the installation of the product before you have read and understood the
instructions and warnings contained in this installation sheet. If you have any question
regarding any of the instruction or warning, please contact your local distributor.
• Please refer to installation guide recommendation for required distance from wall to
avoid risk of property damage.
• This product should only be installed by someone of good mechanical aptitude, with
experience and basic building, and fully understands.
• Make sure that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
• Never exceed the maximum load capacity.
• If mounting to wood wall studs, make sure that mounting screws are anchored into
the center of the studs. Use of an “edge to edge” stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the items,
greatly reducing their holding power.
• This products intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
21
Component Checklist
IMPORTANT: Ensure you have received all parts against the component checklist prior to installing. If any parts
are missing or faulty, telephone the special franchiser for a replac ement.
Package M
Package W
Tools required
Phillips Head Screw driver(200mm length exclude the handle)
M6 Socket and wrench
Electric drill and 10mm masonry bit for concrete wall installation
Marking Pen
Hammer
·
·
·
·
·
ST6.3x55 (x6)
W-A
lag bolt concrete anchor
W-B
(x6) D (ø xø )
washer (x6)
W-C
6 6.3 16
M4x10
M-A
(x4) M5x10 (x4)
M-B
D4 ( 4.5x )
washer (x4)
M-E
ø ø10 D (ø .5xø )
washer (x4)
M-F
5 5 12
M6x10 (x4)
M-C
D6 (ø6.3xø )
washer (x4)
M-G
16
M8x15 (x4)
M-D
D8 (ø8.3xø )
(x5)
M-H
16
washer
ø13.5xø5.5x3.2 (x4)
M-I
decorative cover 1
C
(x1)
left decorative cover (x1)
Gright decorative cover (x1)
H
wall plate(x1)
A
adapter bracket (x1)
B
grip holder (x1)
I
M8 (x1)
M-J
M8 (x2)
M-K
M8x20 (x1)
M-L
M8x50 (x1)
M-M
M8 (x1)
M-N
decorative cover 2 (x1)
D
decorative cover 3
E
(x1) decorative cover 4 (x1)
F
washer (x1)
M-O
43
WOOD STUD WALL MOUNTING:
1a
WARNING
• Make sure that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
• Tighten wood screws firmly, but do not over tighten. Over tightening can damage
the screws, greatly reducing their holding power.
• Make sure that mounting screws are anchored into the center of the studs. Use of
an “edge to edge” stud finder is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall
or plaster into studs. Installers are responsible to provide hardware for other types
of mounting situations.
fig. 1.1
WARNING
• When installing wall mounts on cinder block, verify that you have a minimum of
1-3/8” of actual concrete thickness in the hole to be used for the concrete anchors.
Do not drill into mortar joints! Be sure to mount in a solid part of the block,
generally 1” minimum from the side of the block. It is suggested electric drill on
slow setting is used to drill the hole instead of a hammer drill to avoid breaking out
the back of the hole when entering a void or cavity.
• Installer must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
SOLID BRICK AND CONCRETE BLOCK MOUNTING:
1b
• Pre-drill these holes with a 10mm masonry bit to at least 60mm in depth. Insert a Concrete Anchor (W-B)
into each of these holes. Attach the Wall Plate to the wall using six wood screws (W-A) and six washers
(W-C), as shown in fig.1.3.
• Use the Wall Plate as a template to mark six holes locations on the wall, as shown in fig.1.2.
recommended. Based on their edges, draw a vertical line down each stud’s center.
• Place wall plate on wall as a template. And mark the center of the two mounting holes. Make sure that
the mounting holes are on the stud centerline.
• Drill two 1/8” (3mm) dia. Holes 1.2” (30mm) deep. Make sure that the wall plate is level, secure it using
two wood screws (W-A) and two washers(W-C) as shown in fig. 1.1.
• Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly
Stud
W-A
W-C
fig. 1.2 fig. 1.3
• Assembled the adapter bracket with appropriate parts as shown in fig.2.1.
• Assembled the adapter bracket and arm of wall plate with appropriate screw, washers and nut. As shown
in fig.2.2.
2Adapter bracket Mounting
W-A
W-B
W-C

Produktspezifikationen

Marke: HQ
Kategorie: Tv-meubel
Modell: TVS--FSB07B

Brauchst du Hilfe?

Wenn Sie Hilfe mit HQ TVS--FSB07B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten