HQ Power VDP575MHS20FL Bedienungsanleitung
HQ Power
Effektmaschine
VDP575MHS20FL
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr HQ Power VDP575MHS20FL (46 Seiten) in der Kategorie Effektmaschine. Dieser Bedienungsanleitung war fĂĽr 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/46
VDP575MHS20FL
AERON 575S MOVING HEAD
AERON 575S MOVING HEAD
PROJECTEUR LYRE AERON 575S
CABEZA MĂ“VIL AERON 575S
AERON 575S MOVING-HEAD-SCHEINWERFER
USER MANUAL
GEBRUIKERSHANDLEIDING
NOTICE D’EMPLOI
MANUAL DEL USUARIO
BEDIENUNGSANLEITUNG
VDP575MHS20FL_v3 HQPOWER
2
VDP575MHS20FL – AERON 575S MOVING HEAD
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm
the environment.
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized
company for recycling.
This device should be returned to your distributor or to a local recycling service.
Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing HQPOWER! Your moving head should come in a flight case and with a 575W Sylvania light
bulb, an XLR connexion cable, a safety cable with quick-lock hook and this manual. Please read the manual thoroughly
before bringing this device into service. If the device was damaged in transit, do not install or use it and contact your
dealer.
2. Safety Instructions
• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer
will not accept responsibility for any ensuing defects or problems.
• A qualified technician should install and service this device.
• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device
against damage by leaving it switched off oom temperature. until it has reached r
• This device falls under protection class I. It is therefore essential that the device be earthed. Have a qualified
person carry out the electric connection.
• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.
• Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the plug only.
• There may be some smoke or a particular smell when the device is activated for the first time. This is normal and
any smoke or smell will gradually disappear.
• Do not look directly at the light source as sensitive people may go into epileptic seizure if they do.
• Note that damage caused by user modifications to the device is not covered by the warranty.
• Keep the device away from children and unauthorised users.
3. General Guidelines
• This device is designed for professional use on stage, in discos, theatres, etc. The VDP575MHS20FL should only
be used indoors and connected to an alternating current of max. 230VAC / 50Hz.
• Lighting effects are not designed for permanent operation: regular operation breaks will prolong their lives.
• Do not shake the device. Avoid brute force when installing or operating the device.
• Select a location where the device is protected against extreme heat (see “Technical Specifications”), dust and
moisture. Respect a minimum distance of 0.5m between the device’s light output and any illuminated surface.
Be very careful during the installation: touching live wires can cause life-threatening electroshocks.
Do not touch the device during operation as the housing heats up.
Keep this device away from rain and moisture.
Unplug the mains lead before opening the housing.
VDP575MHS20FL_v3 HQPOWER
3
• Use an appropriate safety cable to fix the device (e.g. VDLSC8).
• Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified
people. Any damage that may occur will most probably be due to unprofessional use of the device.
• Use the original packaging if the device is to be transported.
• All modifications of the device are forbidden for safety reasons.
• Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks,
crash, etc. Using the device in an unauthorised way will void the warranty.
4. Installation
a. Lamps
• Only fit or replace a lamp when the device is unplugged from the mains.
• Let a lamp cool down before replacing it as the temperature of a lamp can reach 700°C during operation.
• When handling a halogen lamp, do not touch it with your bare hands. Use a cloth to insert or remove it.
• Do not install lamps with a higher wattage than what this device was designed for.
• Replace any deformed or damaged lamp with a lamp of the same
type (see “Technical Specifications”):
1. Open the top cover of the rear panel by unscrewing the 3 screws
marked X, Y and Z.
2. Remove the old lamp from the socket and insert the new one
tightly into the socket.
3. Adjust the lamp holder (1 ~ 1.5mm from the lens) by fine-tuning
the 3 screws marked A, B and C to get maximum light output.
4. Close the lamp compartment.
b. Lamp Adjustment
The AERON 575S lamp holder is aligned at the factory. Due to differences between lamps, fine adjustment
may improve light performance. Strike the lamp, open the shutter and the iris. Set the dimmer intensity to
100% and focus the light on a flat surface. Centre a hot spot (the brightest part of the image) by using the 3
adjustment screws “A, B, C”. Turn one screw after another a quarter-turn clockwise or counter-clockwise .If
you cannot detect the hot spot adjust the lamp until the light is evenly distributed.
c. Adjusting the Beam Angle
The lens system can be configured in the range between 8° and 22°. To set the desired beam angle, loose the
2 adjusting screws on the lens unit and adjust the required beam angle. Tighten the adjusting screws again
and fix back the front cover.
d. Inserting / Exchanging Gobos
• Turn off the projector and let it cool down
for 10 minutes. Disconnect the device
from the mains.
• Open the top covers on the moving head
by unscrewing the screws.
• Press the borders of the fixation rings
and remove. Remove the gobo and insert
a new one. Insert the fixation ring in front
of the new gobo.
• Close the compartment.
Produktspezifikationen
| Marke: | HQ Power |
| Kategorie: | Effektmaschine |
| Modell: | VDP575MHS20FL |
Brauchst du Hilfe?
Wenn Sie Hilfe mit HQ Power VDP575MHS20FL benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Effektmaschine HQ Power
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
Bedienungsanleitung Effektmaschine
- Effektmaschine NGS
- Effektmaschine Velleman
- Effektmaschine König
- Effektmaschine Pyle
- Effektmaschine Antari
- Effektmaschine BeamZ
- Effektmaschine Stairville
- Effektmaschine American DJ
- Effektmaschine Karma
- Effektmaschine Adj
- Effektmaschine Behringer
- Effektmaschine Eurolite
- Effektmaschine Showtec
- Effektmaschine Monoprice
- Effektmaschine Lexicon
- Effektmaschine Monacor
- Effektmaschine HQ
- Effektmaschine Viking
- Effektmaschine Elation
- Effektmaschine Cameo
- Effektmaschine Qtx
- Effektmaschine Midas
- Effektmaschine Black Lion Audio
- Effektmaschine Martin
- Effektmaschine Steren
- Effektmaschine TCM FX
- Effektmaschine Fun Generation
- Effektmaschine Futurelight
- Effektmaschine IMG Stage Line
- Effektmaschine TC Electronic
- Effektmaschine Lab Gruppen
- Effektmaschine Hazebase
- Effektmaschine Doepfer
- Effektmaschine Chauvet
- Effektmaschine Valueline
- Effektmaschine Laserworld
- Effektmaschine Klark Teknik
- Effektmaschine Eliminator Lighting
- Effektmaschine BoomTone DJ
- Effektmaschine Sagitter
- Effektmaschine Drawmer
- Effektmaschine DJPower
- Effektmaschine The Confetti Maker
- Effektmaschine Blizzard
- Effektmaschine ColorKey
- Effektmaschine Lotronic
- Effektmaschine Valcom
- Effektmaschine Evo-Lite
- Effektmaschine IGS Audio
- Effektmaschine Magmatic
- Effektmaschine Technical Pro
- Effektmaschine Rosco
- Effektmaschine Showven
Neueste Bedienungsanleitung fĂĽr -Kategorien-
10 Oktober 2024
8 Oktober 2024
6 Oktober 2024
2 Oktober 2024
2 Oktober 2024
2 Oktober 2024
30 September 2024
30 September 2024
28 September 2024
25 September 2024