Hotpoint WDD 9640B Bedienungsanleitung
Hotpoint
Waschtrockner
WDD 9640B
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Hotpoint WDD 9640B (84 Seiten) in der Kategorie Waschtrockner. Dieser Bedienungsanleitung war fĂĽr 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/84
GB
1
! This symbol reminds you to read this instruction manual.
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washer-dryer, 4-5
Control panel
Display
How to run a wash cycle or a drying cycle, 6
Wash cycles and functions, 7
Table of wash cycles
Wash functions
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Precautions and tips, 9
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washer-dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
WDD 9640
Instructions for use
WASHER-DRYER
English,1
GB
Français,13
F DE
Deutsch,25
Nederlands,37
NL
PortuguĂŞs,61
PT
ES
Español,49
Türkçe,73
TR
2
GB
Levelling the machine correctly will provide it with stability,
help to avoid vibrations and excessive noise and prevent it
from shifting while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow a sufficient
ventilation space underneath the washer-dryer.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the supply pipe
by screwing it to a cold
water tap using a Âľ gas
threaded connection (see
figure).
Before performing the con-
nection, allow the water to
run freely until it is perfectly
clear.
2. Connect the inlet hose
to the washer-dryer by
screwing it onto the corre-
sponding water inlet of the
appliance, which is situa-
ted on the top right-hand
side of the rear part of the
appliance . (see figure)
3. Make sure that the hose is not folded over or bent.
! The water pressure at the tap must fall within the values
indicated in the Technical details table (see page 3).
! If the inlet hose is not long enough, contact a specialised
shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
! This instruction manual should be kept in a safe place for
future reference. If the washer-dryer is sold, transferred or
moved, make sure that the instruction manual remains with
the machine so that the new owner is able to familiarise
himself/herself with its operation and features.
! Read these instructions carefully: they contain vital infor-
mation relating to the safe installation and operation of the
appliance.
Unpacking and levelling
Unpacking
1. Remove the washer-dryer from its packaging.
2. Make sure that the washer-dryer has not been damaged
during the transportation process. If it has been damaged,
contact the retailer and do not proceed any further with the
installation process.
3. Remove the protective 4
screws (used during tran-
sportation) and the rubber
washer with the correspon-
ding spacer, located on the
rear part of the appliance
( ).see figure
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need them
again if the washer-dryer needs to be moved to another
location.
! Packaging materials should not be used as toys for
children.
Levelling
1. Install the washer-dryer on a flat sturdy floor, without re-
sting it up against walls, furniture cabinets or anything else.
2. If the floor is not perfectly
level, compensate for any
unevenness by tightening
or loosening the adjusta-
ble front feet ( ); see figure
the angle of inclination,
measured in relation to the
worktop, must not exceed
2°.
Installation
GB
3
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a drai-
nage duct or a wall drain
located at a height between
65 and 100 cm from the
floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
( ). The free end see figure
of the hose should not be
underwater.
! We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150 cm
in length.
Electrical connections
Before plugging the appliance into the electricity socket,
make sure that:
• the socket is earthed and complies with all applicable
laws;
• the socket is able to withstand the maximum power load
of the appliance as indicated on the Technical Data Plate
fixed on the machine;
• the power supply voltage falls within the values indicated
on the Technical Data Plate fixed on the machine;
• the socket is compatible with the plug of the washer-dr-
yer. If this is not the case, replace the socket or the plug.
! The washer-dryer must not be installed outdoors, even
in covered areas. It is extremely dangerous to leave the
appliance exposed to rain, storms and other weather
conditions.
! When the washer-dryer has been installed, the electricity
socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced by autho-
rised technicians.
Warning! The company shall not be held responsible in the
event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before you use
it for the first time, run a wash cycle with detergent and no
laundry, using the cycle “Auto Clean”
Technical data
Model WDD 9640
Dimensions
width 59.5 cm
height 85 cm
depth 60,5 cm
Capacity from 1 to 9 kg for the wash programme
from 1 to 6 kg for the drying programme
Electrical
connections
please refer to the technical data plate fixed
to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed up to 1400 rotations per minute
Energy rated
programmes
according to
regulation
EN 50229
Wash: programme ; temperature 60°C
(2 press of the button)nd ; using a load of 9 kg.
Drying: the smaller load must be dried by
selecting the “EXTRA” dryness level. The
load must consist of 3 sheets, 2 pillowcases
and 1 hand towel;
the remainder of the load must be dried by
selecting the “EXTRA” dryness level.
This appliance conforms to the following EC
Directives:
- 2004/108/EC (Electromagnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2002/96/EC
Produktspezifikationen
| Marke: | Hotpoint |
| Kategorie: | Waschtrockner |
| Modell: | WDD 9640B |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Hotpoint WDD 9640B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Waschtrockner Hotpoint
8 Oktober 2022
Bedienungsanleitung Waschtrockner
- Waschtrockner Bosch
- Waschtrockner AEG
- Waschtrockner Siemens
- Waschtrockner Bauknecht
- Waschtrockner Electrolux
- Waschtrockner Gorenje
- Waschtrockner Whirlpool
- Waschtrockner BEKO
- Waschtrockner Sharp
- Waschtrockner Candy
- Waschtrockner Daewoo
- Waschtrockner GE
- Waschtrockner Hoover
- Waschtrockner Hotpoint-Ariston
- Waschtrockner Indesit
- Waschtrockner Neff
- Waschtrockner Privileg
- Waschtrockner Zanussi
Neueste Bedienungsanleitung fĂĽr -Kategorien-
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022
8 Oktober 2022