Hotpoint CS1A 300 H TK Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hotpoint CS1A 300 H TK (8 Seiten) in der Kategorie Gefrierschränke. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
INSTRUCTIONS FOR USE
GB
DIAGRAM OF THE APPLIANCE (Fig. 1)
A. Handle.
B. Safety lock (if provided).
C. Gasket.
D. Separator (if provided).
E. Defrost water drain plug.
F. Control panel.
G. Side motor cooling grille.
BEFORE USING THE APPLIANCE
Your new appliance is designed to be used in the
household and similar applications such as:
- kitchen areas in shops, oî…Żces and other working
environments
- farm houses
- by clients in hotels, motels, residences, bed & breakfasts.
The product must only be used to store frozen food, to
freeze fresh food and to make ice.
Regulations require the appliance to be earthed.
The manufacturer declines all liability for injury to
persons or animals and for damage to property
resulting from failure to observe the above procedures
and reminders.
1. After unpacking, make sure that the appliance is
undamaged and that the door closes perfectly, with the
gasket remaining intact. Any damage must be reported
to your retailer within 24 hours after delivery of the
appliance.
2. Wait at least two hours before switching the appliance on
in order to ensure the refrigerant circuit is fully eî…Żcient.
3. Installation and electrical connection must be carried out
by a qualied technician, according to the manufacturer’s
instructions and local safety regulations.
4. Clean the inside of the appliance before using it.
• Before connecting the appliance to the mains supply,
ensure that the voltage corresponds to that given on
the rating plate located on the rear of the appliance.
• Electrical connections must be made in
accordance with local regulations.
INSTALLATION
• Unpack the appliance.
• Remove the 4 spacers inserted between the door
and the appliance. (Fig. 3)
• Make sure the defrost water drain plug (if provided) is
correctly positioned (E).
• For optimum appliance operation and to avoid damage
when the door is opened, leave a space of at least 7 cm
from the rear wall and 7 cm at the sides. (Fig. 4)
• Fit the accessories (if provided).
DIAGRAM OF THE CONTROL PANEL (Fig. 2)
a. Red LED: when î…˛ashing, it indicates that an alarm
condition is present see TROUBLESHOOTING GUIDE.
b. Green LEDs: they indicate that the appliance is in
operation, and the temperature has been set as follows:
b1 less cold temperature (right light on), use this setting
with partial loads will optimise energy consumption.
b2 middle temperature (centre light on)
b3 very cold temperature (left light on)
ALL Green LEDs ON: FAST FREEZING function is active;
see the section “freezing fresh food”.
c. Temperature setting button: to adjust the set
temperature and to activate/deactivate the fast freezing
operations.
To select the desired temperature, repeatedly press the
setting button (3): each time the button is pressed, the set
temperature is updated.
To activate/deactivate fast freezing function, pressing
for approximately 3 seconds: all green LEDs î…˛ash
simultaneously 3 times and then remain lit.
Note:
The settings will be saved in the memory even if
a power cut occurs. The time needed for the temperature
inside the freezer to reach the set value, can vary
depending on climatic conditions and the set temperature
itself.
SWITCHING ON THE APPLIANCE
• Plug in the appliance.
• The green LED lights up (middle temperature).
• The red LED ashes to indicate that the temperature
inside the appliance is not yet suî…Żciently low for food
storage. The red LED will normally switch oî…® within the
î…°rst six hours after the appliance is switched on.
• Place food inside the product only when the red LED has
switched oî…®.
Note:
Thanks to the eî…Żcient lid seal, the appliance lid
will not reopen easily immediately after closing. Wait a few
minutes before re-opening the lid of the appliance.
FREEZING FOOD
Preparation of fresh food for freezing
• Before freezing, wrap and seal fresh food in: aluminium
foil, cling î…°lm, air and water-tight plastic bags,
polyethylene containers with lids, provided they are
suitable for freezing foods.
• Food must be fresh, mature and of prime quality in order
to obtain high quality frozen food.
• Fresh vegetables and fruit should preferably be frozen
as soon as they are picked to maintain the full original
nutritional value, consistency, colour and î…˛avour.
• Always leave hot food to cool before placing in the
appliance.
Freezing fresh food
• Place foods to be frozen in direct contact with the walls
of appliance:
A) - foods to be frozen,
B) - foods already frozen.
• Avoid placing foods to be frozen in direct contact with
food already frozen.
• For best and fastest freezing, foods should be split into
small portions; this will also be useful when the frozen
items are to be used.
1. At least 24 hours before storing fresh foods inside the
product for freezing, activate the fast freezing function by
pressing button for approximately 3 seconds. All green c
LEDs ( ) comes on.b
2. Introduce the food to freeze inside the appliance, and
keep the door of the appliance closed for 24 hours.
After this period the food will be frozen. The fast freezing
function can be deactivated pressing button for c
approximately 3 seconds.
If the fast freeze function is not manually deactivated, it
will be automatically deactivated by the appliance after
50 hours.
FOOD STORAGE
Refer to the table on the appliance.
Classiî…°cation of frozen foods
Load and classify the frozen foods; it is advisable to indicate
the storage date on the packs, to ensure consumption
before the expiry dates listed in months in î…°g. 6 for each
type of food.
Advice for storing frozen food
When buying frozen food, make sure that:
• The packaging is intact (food in damaged containers
may have deteriorated). If a package is swollen or has
damp patches, the product may not have been stored
in optimum conditions and therefore undergone partial
defrosting.
• When shopping, leave frozen food purchases until last
and carry them in a thermally insulated bag.
• On arriving home, immediately place the frozen food in
the appliance.
• Avoid or minimise temperature variations. Observe the
expiry date on the packaging.
• Always follow the storage instructions on frozen food
packages.
Note:
• Eat fully or partially defrosted foods immediately. Do
not refreeze unless the food is cooked after it has
thawed. Once cooked, the food can be refrozen.
• In case of a prolonged power failure:
Do not open the appliance door, except to place
ice packs (if provided) over the frozen foods on the
right and left side of the appliance. This will slow
down the rise in temperature.
PRECAUTIONS AND SUGGESTIONS
• During installation, make sure the appliance does
not damage the power cable.
• Do not store glass containers with liquids inside the
product as they may break.
• Do not eat ice cubes or ice lollies immediately after
taking them out of the appliance as they may cause cold
burns.
• Before carrying out any maintenance or cleaning, always
unplug the appliance or disconnect the power supply.
• Do not install the appliance in places exposed to direct
sunlight or near heat sources in order to avoid increasing
power consumption.
• Do not put aerosol spray cans or recipients containing
propellants or î…˛ammable substances in the appliance.
• Do not store or use gasoline or other ammable liquids
and gases in the vicinity of this or any other domestic
appliance. The fumes can create a î…°re hazard or
explosion.
• Install the appliance in a perfectly horizontal position, on
a î…˛oor strong enough to take its weight and in an area
suitable for its size and use.
• Install the appliance in a dry, well-ventilated place.
The appliance is set for operation at speciî…°c ambient
temperature ranges, according to the climatic class
indicated on the data plate located at the rear of the
product (Fig. 7). The appliance may not work properly
if it is left for a long time at a temperature outside the
speciî…°ed range.
• It is advisable to leave the appliance connected if left
empty even for short periods.
• Be careful not to damage the oors when you move the
appliance (e.g. parquet). To facilitate product handling, it
is advisable to empty it beforehand, if possible.
Note:
The appliance must be handled and installed by two
or more persons.
• Do not use mechanical devices or any means other
than those recommended and/or supplied by the
manufacturer to speed up the defrosting process.
• Do not use electrical appliances inside the product,
unless such appliances are speciî…°cally recommended by
the manufacturer.
• The bulb used inside the appliance is specically
designed for domestic appliances and is not suitable for
general room lighting within the home (EC Regulation
244/2009).
• This appliance must not be used by children under
8 years of age, or by people with limited physical,
sensory or mental abilities or without experience
and knowledge of it, unless instructed in its use by
those responsible for their safety.
• Do not allow children to play or hide inside the
product: risk of becoming trapped inside and
suî…®ocating.
• Power cable modication or replacement must only
be carried out by qualied personnel or After‑sales
Service.
• Do not use extension leads or adapters.
• Electrical disconnection must be possible either by
unplugging the appliance or by means of a double‑
pole switch located upline from the socket.
• Ensure that the voltage indicated on the appliance
data plate corresponds to the domestic supply
voltage.
• Do not ingest the contents (non‑toxic) of the ice
packs (if provided).
• Restrict the number of times you open the door.
• This appliance features “skin condenser”
technology: the condensing unit is integrated into
the walls of the freezer. For this reason the side and
front walls of the product may become hot while
the product is running. This is entirely normal and
also reduces the risk of condensation forming in
particularly critical environmental conditions (see
paragraph “Troubleshooting guide”).
APPLIANCE DEFROSTING
The appliance should be defrosted when the thickness of
ice on the walls reaches 5-6 mm.
• Disconnect the appliance from the power supply.
• Remove food from the appliance and put it in a very cool
place or a thermally insulated bag.
• Leave the appliance door open.
• Remove the internal defrost water drain plug (depending
on model) (Fig. 8).
• Remove the external defrost water drain plug (depending
on model) and reposition it as shown in î…°gure 8.
• Use the separator (depending on model) inside the
product as a recipient for any remaining water, (D) as
shown in î…°g. 8. If there is no separator, use a shallow
container.
• Defrosting can be sped up by using a spatula to detach
the frost from the appliance walls.
• Remove the frost from the bottom of the appliance.
• In order to avoid permanent damage to the
appliance interior, do not use pointed or sharp
metal instruments to remove the ice.
• Do not use abrasive products or heat up the interior
artiî…°cially.
• Dry the inside of the appliance thoroughly.
• Ret the plug after defrosting.
CLEANING AND MAINTENANCE
• Remove the frost from the upper edges (see
Troubleshooting Guide).
• Clean the inside after defrosting, using a sponge
dampened with warm water and/or mild detergent.
• Clean the side vent (if provided).
Unplug the appliance before carrying out maintenance
operations. Do not use abrasive products, scourers
or stain‑removers (e.g. acetone, trichloroethylene) to
clean the appliance.
To obtain the best results from your appliance, carry
out cleaning and maintenance at least once a year.
CHANGING THE LID LIGHT BULB (if provided)
• Disconnect the appliance from the mains power supply.
• Remove the diuser by following the sequence of steps
shown in the î…°gure.
• Unscrew the light bulb and replace it with an identical
bulb of the same wattage and voltage.
• Ret the diuser and plug in the appliance.
TROUBLESHOOTING GUIDE
1. The red LED î…˛ashes.
• Is there a power failure?
• Is a defrosting operation in progress?
• Has fresh food recently been introduced?
• Is the appliance lid properly closed?
• Is the appliance placed near a heat source?
• Are the ventilation grille and condenser clean?
2. All LEDs î…˛ash at the same time.
• Contact the After-Sales Service.
3. The appliance is too noisy.
• Is the appliance perfectly horizontal?
• Is the appliance in contact with other furniture or
objects that may cause vibrations?
• Has the packaging been removed from under the
appliance?
Note:
Gurgling noises from the refrigerating circuit after the
compressor cuts out are perfectly normal.
4. All LEDs are oî…® and the product is not working.
• Is there a power failure?
• Is the plug properly inserted in the socket?
• Is the electric cable intact?
5. All LEDs are oî…® and the product is working.
• Contact the After-Sales Service.
6. The compressor runs continuously.
• Have hot foods been put in the appliance?
• Has the appliance lid been left open for a long time?
• Is the appliance placed in a very warm room or near
heat sources?
• Has the fast freeze function been activated? (All green
LEDs ON)
7. Too much ice on the upper edge.
• Are the defrost water drainage plugs correctly
positioned?
• Is the appliance lid properly closed?
• Is the appliance lid seal damaged or deformed? (See
chapter “Installation”)
• Have the 4 protection pieces been removed? (See
chapter “Installation”)
8. Formation of condensate on the external walls of
the appliance.
• It is normal for condensation to form under certain
atmospheric conditions (humidity above 85%) or if the
appliance is located in a damp or poorly ventilated
room. The performance of the appliance is in no way
aî…®ected.
9. The layer of ice on the internal walls of the
appliance is not uniform.
• This phenomenon is quite normal.
SAFEGUARDING THE ENVIRONMENT
1. Packing
The packing material is 100% recyclable and bears the
recycling symbol. For disposal, comply with the local
regulations. Keep the packing materials (plastic bags,
polystyrene parts, etc.) out of the reach of children, as they
are a potential source of danger.
2. Scrapping/Disposal
The appliance is manufactured using recyclable material.
This appliance is marked in compliance with European
Directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE). By ensuring the correct disposal of
this appliance, you can help prevent potentially negative
consequences for the environment and the health of persons.
The symbol on the appliance, or on the accompanying
documents, indicates that this appliance should not be
treated as domestic waste but must be taken to a special
collection centre for the recycling of electrical and electronic
equipment.
When scrapping the appliance, make it unusable by cutting
oî…® the power cable and removing the doors and shelves
so that children cannot easily climb inside and become
trapped.
Scrap the appliance in compliance with local regulations
on waste disposal, taking it to a special collection centre;
do not leave the appliance unattended even for a few days,
since it is a potential source of danger for children.
For further information on the treatment, recovery and
recycling of this product, contact your competent local
oî…Żce, the household waste collection service or the shop
where you purchased the appliance.
Information:
This appliance does not contain CFCs. The refrigerant
circuit contains R134a (HFC) or R600a (HC) (see the rating
plate inside the appliance).
Appliances with Isobutane (R600a): isobutane is a natural
gas without environmental impact, but is î…˛ammable.
Therefore, make sure the refrigerant circuit pipes are not
damaged.


Produktspezifikationen

Marke: Hotpoint
Kategorie: Gefrierschränke
Modell: CS1A 300 H TK

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hotpoint CS1A 300 H TK benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Gefrierschränke Hotpoint

Bedienungsanleitung Gefrierschränke

Neueste Bedienungsanleitung fĂĽr -Kategorien-