Honeywell 4800p Bedienungsanleitung

Honeywell Barcode-Leser 4800p

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Honeywell 4800p (184 Seiten) in der Kategorie Barcode-Leser. Dieser Bedienungsanleitung war für 44 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/184

™

4800p

4800p 2D Imager

User’s Guide

Disclaimer

Hand Held Products, Inc. (“Hand Held Products”) reserves the right to make

changes in specifications and other information contained in this document

without prior notice, and the reader should in all cases consult Hand Held

Products to determine whether any such changes have been made. The

information in this publication does not represent a commitment on the part of

Hand Held Products.

Hand Held Products shall not be liable for technical or editorial errors or

omissions contained herein; nor for incidental or consequential damages

resulting from the furnishing, performance, or use of this material.

This document contains proprietary information that is protected by copyright. All

rights are reserved. No part of this document may be photocopied, reproduced,

or translated into another language without the prior written consent of Hand

Held Products.

Web Address: www.handheld.com

Microsoft® Windows® is either a registered trademark or trademarks of Microsoft

Corporation in the United States and/or other countries.

Macintosh® is a trademark of Apple Computer, Inc., registered in the U.S. and

other countries.

Other product names or marks mentioned in this document may be trademarks

or registered trademarks of other companies and are the property of their

respective owners.

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

FCC Class B Compliance Statement

This equipment has been tested and found to comply with the limits for a Class

B digital device pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio or television technician for help.

Caution: Any changes or modifications made to this equipment not

expressly approved by Hand Held Products, Inc. may void the

FCC authorization to operate this equipment.

Note: To maintain compliance with FCC Rules and Regulations, cables

connected to this device must be Hand Held Products approved shielded

cables, in which the cable shield wire(s) have been grounded (tied) to the

connector shell. Installation of the included ferrite is required to meet

emission requirements.

Canadian Notice

This equipment does not exceed the Class B limits for radio noise emissions as

described in the Radio Interference Regulations of the Canadian Department of

Communications.

Le present appareil numerique n’emet pas de bruits radioelectriques depassant

les limites applicables aux appareils numeriques de la classe B prescrites dans

le Reglement sur le brouillage radioelectrique edicte par le ministere des

Communications du Canada.

Note: To maintain compliance with FCC Rules and Regulations, cables

connected to this device must be shielded cables, in which the cable

shield wire(s) have been grounded (tied) to the connector shell.

Installation of the included ferrite is required to meet emission

requirements.

CE Mark

The CE mark on the product indicates that the system has been

tested to and conforms with the provisions noted within the 2004/108/

EC Electromagnetic Compatibility Directive and the 2006/95/EC Low

Voltage Directive.

Complies with:

EN55022:2006 (for ITE emissions)

EN55024:1998 (for ITE immunity)

EN61000-3-2:2000

EN61000-3-3:1995

For further information please contact:

Hand Held Products

Nijverheidsweg 9-13

5627 BT Eindhoven

The Netherlands

Chapter 1 - Getting Started

About This Manual ............................................................... 1-1

Unpacking the Imager........................................................... 1-1

Imager Models ...................................................................... 1-2

Imager Identification ............................................................ 1-2

Connecting the Imager with USB ........................................ 1-3

Programming the Interface - Plug and Play.......................... 1-4

USB PC or Macintosh® Keyboard ................................. 1-4

USB HID........................................................................ 1-4

USB COM Port Emulation............................................. 1-5

Reading Techniques.............................................................. 1-5

4800p Stand .......................................................................... 1-6

Chapter 2 - Terminal Interfaces

Terminal ID .......................................................................... 2-1

Supported Terminals............................................................. 2-2

Keyboard Country ................................................................ 2-3

Keyboard Style ..................................................................... 2-5

Keyboard Modifiers ............................................................. 2-7

Chapter 3 - Output

Good Read Indicators ........................................................... 3-1

Beeper – Good Read ...................................................... 3-1

Beeper Volume – Good Read ........................................ 3-1

Beeper Pitch – Good Read ............................................. 3-2

Beeper Duration – Good Read ....................................... 3-2

Number of Beeps – Good Read ..................................... 3-2

Good Read Delay.................................................................. 3-3

User-Specified Good Read Delay......................................... 3-3

Reread Delay ........................................................................ 3-4

User-Specified Reread Delay ............................................... 3-4

LED Power Level ................................................................. 3-5

Centering............................................................................... 3-5

Table of Contents

Decode Search Mode............................................................ 3-7

Output Sequence Overview .................................................. 3-7

Output Sequence Editor ............................................... 3-10

Require Output Sequence............................................. 3-10

Print Weight........................................................................ 3-11

Video Reverse..................................................................... 3-11

Working Orientation........................................................... 3-12

Chapter 4 - Data Editing

Prefix/Suffix Overview......................................................... 4-1

To Add a Prefix or Suffix: ............................................. 4-2

To Clear One or All Prefixes or Suffixes:...................... 4-3

To Add a Carriage Return Suffix to all Symbologies.... 4-3

Prefix Selections............................................................. 4-4

Suffix Selections ............................................................ 4-4

Function Code Transmit................................................. 4-4

Intercharacter, Interfunction, and Intermessage Delays ....... 4-5

Intercharacter Delay ....................................................... 4-5

User Specified Intercharacter Delay .............................. 4-6

Interfunction Delay ........................................................ 4-6

Intermessage Delay ........................................................ 4-7

Chapter 5 - Data Formatting

Data Format Editor Introduction .......................................... 5-1

To Add a Data Format.................................................... 5-1

Other Programming Selections ...................................... 5-2

Data Format Editor Commands ..................................... 5-2

Data Format Editor......................................................... 5-5

Data Formatter ............................................................... 5-5

Alternate Data Formats .................................................. 5-6

iii

Chapter 6 - Symbologies

Message Length Description................................................. 6-2

Codabar Start/Stop Characters....................................... 6-3

Codabar Check Character............................................... 6-3

Codabar Concatenation .................................................. 6-4

Codabar Message Length ............................................... 6-5

Code 39 Start/Stop Characters....................................... 6-6

Code 39 Check Character............................................... 6-6

Code 39 Message Length ............................................... 6-7

Code 39 Append............................................................. 6-8

Code 32 Pharmaceutical (PARAF) ................................ 6-8

Full ASCII ...................................................................... 6-9

Code 39 Code Page ...................................................... 6-10

Check Digit................................................................... 6-10

Interleaved 2 of 5 Message Length .............................. 6-11

Code 93 Message Length ............................................. 6-12

Code 93 Code Page ...................................................... 6-12

Straight 2 of 5 Industrial Message Length ................... 6-13

Straight 2 of 5 IATA Message Length ......................... 6-14

Matrix 2 of 5 Message Length ..................................... 6-15

Check Digits Required ................................................. 6-16

Code 11 Message Length ............................................. 6-16

ISBT 128 Concatenation .............................................. 6-17

Code 128 Message Length ........................................... 6-18

Code 128 Code Page .................................................... 6-18

Telepen Output ............................................................. 6-19

Telepen Message Length.............................................. 6-19

UPC-A Check Digit...................................................... 6-20

UPC-A Number System ............................................... 6-20

UPC-A Addenda........................................................... 6-21

UPC-A Addenda Required........................................... 6-21

UPC-A Addenda Separator .......................................... 6-21

UPC-E0 ........................................................................6-22

UPC-E0 Expand ........................................................... 6-22

UPC-E0 Addenda Required ......................................... 6-23

UPC-E0 Addenda Separator......................................... 6-23

vii

Troubleshooting .................................................................. 13-2

Chapter 14 - Customer Support

Technical Assistance........................................................... 14-1

Online Technical Assistance ........................................ 14-2

For Further Information................................................ 14-2

Product Service and Repair................................................. 14-2

Online Product Service and Repair Assistance ............ 14-3

Limited Warranty................................................................ 14-3

Appendix A

Symbology Chart ................................................................. A-1

ASCII Conversion Chart (Code Page 1252)........................ A-4

Code Page Mapping of Printed Bar Codes .......................... A-6

viii

4800p 2D Imager User’s Guide 1 - 3

Connecting the Imager with USB

Note: See "Imager Models" on page 1-2 to determine which interfaces apply to

your imager.

An imager can be connected to the USB port of a computer.

1. Connect the appropriate interface cable to the imager first, then to the com-

puter.

2. Program the imager for a USB interface using the Plug and Play bar codes

beginning on page 1-4.

3. The imager beeps.

4. Verify the imager operation by scanning a bar code from the Sample

Symbols in the back of this manual.

For additional USB programming and technical information, refer to Hand Held

Products “USB Application Note,” available at www.handheld.com.

1 - 4 4800p 2D Imager User’s Guide

Programming the Interface - Plug and Play

Plug and Play bar codes provide instant imager set up for commonly used

interfaces.

Note: After you scan one of the codes, power cycle the host terminal to have the

interface in effect.

Note: See "Imager Models" on page 1-2 to determine which interfaces apply to

your imager.

USB PC or Macintosh® Keyboard

Scan one of the following codes to program the imager for USB PC Keyboard or

USB Macintosh Keyboard. Scanning these codes adds a CR and selects the

terminal ID (USB PC Keyboard - 124, USB Macintosh Keyboard - 125, USB

Japanese Keyboard - 134).

USB HID

Scan the following code to program the imager for USB HID bar code imagers.

Scanning this code changes the terminal ID to 131.

USB Keyboard (PC)

USB Keyboard (Mac)

USB Japanese Keyboard (PC)

USB HID Bar Code Imager

1 - 6 4800p 2D Imager User’s Guide

The 4800p’s viewfinder projects a green aiming beam that should be centered

over the bar code, but can be positioned in any direction for a good read.

Hold the scanner with the aiming beam centered over the bar code. The 4800p

beeps when it successfully reads a bar code. Do not move the 4800p over

another bar code until it beeps. The optimum distance between the 4800p and

the object being scanned is 2 to 5 inches (5.1 - 12.7 cm). The height from the

4800p to the stand’s tray is the proper distance.

The aiming beam is smaller when the imager is closer to the code and larger

when it is farther from the code. Symbologies with smaller bars or elements (mil

size) should be read closer to the unit. Symbologies with larger bars or elements

(mil size) should be read farther from the unit. If the code being scanned is highly

reflective (e.g., laminated), it may be necessary to tilt the code +5° to prevent

unwanted reflection.

4800p Stand

The stand holds the 4800p at a fixed distance for capturing images or reading

bar codes on security/identification cards. The wedge insert supplied with the

stand provides the optimum angle for scanning and capturing images in most

lighting conditions. The card should be placed on the wedge with the bar code

closest to the back of the stand.

Linear bar code 2D Matrix symbol

2 - 6 4800p 2D Imager User’s Guide

Shift Lock

is used when you normally have the Shift Lock key on (not common

to U.S. keyboards).

Automatic Caps Lock

is used if you change the Caps Lock key on and off. The

software tracks and reflects if you have Caps Lock on or off (AT and PS/2 only).

This selection can only be used with systems that have an LED which notes the

Caps Lock status.

Autocaps via NumLock

bar code should be scanned in countries (e.g.,

Germany, France) where the Caps Lock key cannot be used to toggle Caps

Lock. The NumLock option works similarly to the regular Auotcaps, but uses the

NumLock key to retrieve the current state of the Caps Lock.

Emulate External Keyboard

should be scanned if you do not have an external

keyboard (IBM AT or equivalent).

Note: After scanning the Emulate External Keyboard bar code, you must power

cycle your computer.

Shift Lock

Automatic Caps Lock

Autocaps via NumLock

Emulate External Keyboard

4800p 2D Imager User’s Guide 3 - 1

Output

Good Read Indicators

Beeper – Good Read

The beeper may be programmed

Off

in response to a good read. Turning

this option off, only turns off the beeper response to a good read indication. All

error and menu beeps are still audible.

Default = On.

Beeper Volume – Good Read

The beeper volume codes modify the volume of the beep the imager emits on a

good read.

Default = High

* On

Off

* High

Medium

Off

Low

4800p 2D Imager User’s Guide 3 - 9

Note: Code 93 must be enabled to use this example.

You would set up the sequence editor with the following command line:

SEQBLK62999941FF6A999942FF69999943FF

The breakdown of the command line is shown below:

SEQBLK sequence editor start command

62 code identifier for Code 39

9999 code length that must match for Code 39, 9999 = all lengths

41 start character match for Code 39, 41h = “A”

FF termination string for first code

6A code identifier for Code 128

9999 code length that must match for Code 128, 9999 = all lengths

42 start character match for Code 128, 42h = “B”

FF termination string for second code

69 code identifier for Code 93

9999 code length that must match for Code 93, 9999 = all lengths

43 start character match for Code 93, 43h = “C”

FF termination string for third code

To program the previous example using specific lengths, you would have to

count any programmed prefixes, suffixes, or formatted characters as part of the

length. If you use the example on page 3-8, but assume a <CR> suffix and

specific code lengths, you would use the following command line:

SEQBLK62001241FF6A001342FF69001243FF

The breakdown of the command line is shown below:

SEQBLK sequence editor start command

62 code identifier for Code 39

0012 A - Code 39 sample length (11) plus CR suffix (1) = 12

A - Code 39

B - Code 128

C - Code 93

3 - 10 4800p 2D Imager User’s Guide

41 start character match for Code 39, 41h = “A”

FF termination string for first code

6A code identifier for Code 128

0013 B - Code 128 sample length (12) plus CR suffix (1) = 13

42 start character match for Code 128, 42h = “B”

FF termination string for second code

69 code identifier for Code 93

0012 C - Code 93 sample length (11) plus CR suffix (1) = 12

43 start character match for Code 93, 43h = “C”

FF termination string for third code

Output Sequence Editor

Require Output Sequence

When an output sequence is

Required

, all output data must conform to an edited

sequence or the imager will not transmit the output data to the host device.

When it’s

On/Not Required

, the imager will attempt to get the output data to

conform to an edited sequence, but if it cannot, the imager transmits all output

data to the host device as is.

When the output sequence is

Off

, the bar code data is output to the host as the

imager decodes it.

Note: This selection is unavailable when the Multiple Symbols Selection is

turned on.

Enter Sequence

Default Sequence

Required

On/Not Required

*Off

Produktspezifikationen

Marke:	Honeywell
Kategorie:	Barcode-Leser
Modell:	4800p

Brauchst du Hilfe?

Wenn Sie Hilfe mit Honeywell 4800p benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Barcode-Leser Honeywell

Honeywell 7800LWN Bedienungsanleitung

6 Oktober 2024

Honeywell Dolphin 99EX Bedienungsanleitung

3 Oktober 2024

Honeywell ScanPal EDA50K Bedienungsanleitung

13 September 2024

Honeywell ScanPal EDA51K Bedienungsanleitung

28 August 2024

Honeywell MS3580 Quantum T Bedienungsanleitung

22 August 2024

Honeywell ScanGlove IS4225 Bedienungsanleitung

12 August 2024

Honeywell Dolphin 7900 Bedienungsanleitung

8 August 2024

Honeywell Dolphin 9950 Bedienungsanleitung

6 August 2024

Honeywell Youjie HF600 Bedienungsanleitung

6 August 2024

Honeywell ScanPal EDA60K Bedienungsanleitung

6 August 2024

Bedienungsanleitung Barcode-Leser

Neueste Bedienungsanleitung für -Kategorien-

Datalogic DSM0422 Bedienungsanleitung

30 November 2024

Datalogic Skorpio X5 Bedienungsanleitung

30 November 2024

Renkforce 7A CR6307A Bedienungsanleitung

3 Oktober 2024

Datalogic MGL8500X Bedienungsanleitung

23 September 2024

IFM O2I501 Bedienungsanleitung

22 September 2024

Datalogic Matrix 120 Bedienungsanleitung

13 September 2024

Datalogic Joya Touch Plus Bedienungsanleitung

12 September 2024

Posiflex CD-3602U Bedienungsanleitung

6 September 2024

Posiflex CD-3202U Bedienungsanleitung

6 September 2024

Brady IRX200 Bedienungsanleitung

6 September 2024