Honeywell 3800g Bedienungsanleitung

Honeywell Barcode-Leser 3800g

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Honeywell 3800g (168 Seiten) in der Kategorie Barcode-Leser. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/168

™

3800/3900

Handheld Linear Imager

User’s Guide

Disclaimer

Hand Held Products, Inc. (“Hand Held Products”) reserves the right to make

changes in specifications and other information contained in this document

without prior notice, and the reader should in all cases consult Hand Held

Products to determine whether any such changes have been made. The

information in this publication does not represent a commitment on the part of

Hand Held Products.

Hand Held Products shall not be liable for technical or editorial errors or

omissions contained herein; nor for incidental or consequential damages

resulting from the furnishing, performance, or use of this material.

This document contains proprietary information that is protected by copyright. All

rights are reserved. No part of this document may be photocopied, reproduced,

or translated into another language without the prior written consent of Hand

Held Products.

Web Address: www.handheld.com

Statement of Agency Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

FCC Class B Compliance Statement

This equipment has been tested and found to comply with the limits for a Class

B digital device pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio or television technician for help.

Caution: Any changes or modifications made to this device that are not

expressly approved by Hand Held Products, Inc. may void the user’s authority

to operate the equipment.

Note: To maintain compliance with FCC Rules and Regulations, cables

connected to this device must be shielded cables, in which the cable shield

wire(s) have been grounded (tied) to the connector shell.

Canadian Notice

This equipment does not exceed the Class B limits for radio noise emissions as

described in the Radio Interference Regulations of the Canadian Department of

Communications.

Le present appareil numerique n’emet pas de bruits radioelectriques depassant

les limites applicables aux appareils numeriques de la classe B prescrites dans

le Reglement sur le brouillage radioelectrique edicte par le ministere des

Communications du Canada.

The CE mark on the product indicates that the system has been

tested to and conforms with the provisions noted within the 89/336/

EEC Electromagnetic Compatibility Directive and the 73/23/EEC

Low Voltage Directive.

For further information please contact:

Hand Held Products

Nijverheidsweg 9-13

Eindhoven, 5627 BT

The Netherlands

Hand Held Products shall not be liable for use of our product with equipment

(i.e., power supplies, personal computers, etc.) that is not CE marked and does

not comply with the Low Voltage Directive.

UL and cUL Statement

UL listed UL1950 and CSA 22.2 No.950. cUL listed UL1950 and CSA 22.2 No

950.

LED Safety Statement

This device has been tested in accordance with EN60825-1 LED safety, and has

been certified to be under the limits of a Class 1 LED device.

TÜV Statement

TÜV or GS marked to EN60950 and EN60825-1.

C-TIC Statement

Conforms to AS/NZS 3548. C-Tick number: N10410.

Patents

Please refer to the 3800/3900 packaging for patent information.

Chapter 1 - Getting Started

Typical Applications for the 3900 ........................................ 1-1

About This Manual ............................................................... 1-1

Unpacking the Scanner ......................................................... 1-2

3800 Scanner Identification.................................................. 1-3

3900 Scanner Identification.................................................. 1-3

Connecting the Scanner When Powered by Host

(Keyboard Wedge) ............................................................ 1-4

Mounting Information for the 3900 ..................................... 1-5

Specular Zone................................................................. 1-6

Plug and Play ........................................................................ 1-6

IBM 4683 Ports 5B, 9B, and 17 Interface ............................ 1-8

USB Interface ....................................................................... 1-9

OCIA Interface ................................................................... 1-11

NCR OCIA Short Format (8 Bit) Interface ........................ 1-11

NCR OCIA Long Format (9 Bit) Interface......................... 1-12

Nixdorf OCIA Interface...................................................... 1-12

Serial Wedge....................................................................... 1-12

Chapter 2 - Terminal Interfaces

Keyboard Wedge Connection............................................... 2-1

Terminal ID ......................................................................... 2-2

Supported Terminals............................................................. 2-3

Keyboard Country ................................................................ 2-5

Keyboard Style ..................................................................... 2-5

Keyboard Modifiers.............................................................. 2-6

Serial Port Connection.......................................................... 2-8

Baud Rate....................................................................... 2-9

RS-232 Word Length: Data Bits, Stop Bits, and Parity2-10

RS-232 Handshaking ................................................... 2-12

Wand Emulation Connection ....................................... 2-12

Wand Emulation Transmission Rate............................ 2-13

Wand Emulation Polarity............................................. 2-14

Wand Emulation Idle ................................................... 2-14

Table of Contents

PDF417 Wand Emulation................................................... 2-15

Data Block Size............................................................ 2-15

Delay Between Blocks ................................................. 2-15

Overall Checksum........................................................ 2-16

Chapter 3 - Output

Scan Rate .............................................................................. 3-1

Beeper Volume ..................................................................... 3-1

Beeper Tone.......................................................................... 3-2

Scan Voting .......................................................................... 3-2

Reduce Quiet Zone ............................................................... 3-2

Reread Delay ........................................................................ 3-3

Good Read Delay.................................................................. 3-4

Trigger Mode........................................................................ 3-4

Chapter 4 - Data Editing

Prefix/Suffix Overview......................................................... 4-1

To Add a Prefix or Suffix: ............................................. 4-1

To Clear One or All Prefixes or Suffixes:...................... 4-2

To Add a Carriage Return Suffix to all Symbologies.... 4-3

Prefix Selections............................................................. 4-4

Suffix Selections ............................................................ 4-4

Symbology Chart.................................................................. 4-5

ASCII Conversion Chart (Code Page 1252)......................... 4-6

Function Code Transmit................................................. 4-7

Intercharacter, Interfunction, and Intermessage Delays ....... 4-7

Intercharacter Delay ....................................................... 4-7

User Specified Intercharacter Delay .............................. 4-8

Interfunction Delay ........................................................ 4-9

Intermessage Delay ........................................................ 4-9

iii

Chapter 5 - Data Formatting

Data Format Editor Introduction........................................... 5-1

To Add a Data Format.................................................... 5-1

Other Programming Selections ...................................... 5-2

Data Format Editor Commands...................................... 5-2

Data Format Editor......................................................... 5-4

Data Formatter................................................................ 5-5

Alternate Data Formats .................................................. 5-5

Chapter 6 - Secondary Interface

Secondary Code 39 Wand Emulation ................................... 6-1

Secondary RS-232 Connection ............................................. 6-1

Secondary Non Decoded Output Laser Emulation............... 6-2

Non Decoded Output Laser Emulation Transmission Rate.. 6-2

Non Decoded Output Laser Emulation Polarity ................... 6-2

Non Decoded Laser Emulation Idle...................................... 6-3

Disabling the Secondary Interface ........................................ 6-3

Secondary Trigger Mode ...................................................... 6-3

Chapter 7 - Symbologies

Introduction........................................................................... 7-1

All Symbologies.................................................................... 7-1

Message Length Description ................................................ 7-2

Codabar ................................................................................. 7-3

Start/Stop Characters ..................................................... 7-3

Check Character ............................................................. 7-4

Concatenation................................................................. 7-5

Codabar Message Length ............................................... 7-5

Code 39 ................................................................................. 7-6

Start/Stop Characters ..................................................... 7-6

Check Character ............................................................. 7-7

Code 39 Message Length ............................................... 7-7

Code 39 Append............................................................. 7-8

Base 32 ........................................................................... 7-8

Full ASCII ...................................................................... 7-9

Interleaved 2 of 5 ................................................................ 7-10

Check Digit .................................................................. 7-10

Interleaved 2 of 5 Message Length .............................. 7-11

Strict Decoding............................................................. 7-11

Code 93............................................................................... 7-12

Code 93 Message Length ............................................. 7-12

Code 2 of 5.......................................................................... 7-13

Code 2 of 5 Message Length........................................ 7-13

IATA Code 2 of 5 ............................................................... 7-14

IATA Code 2 of 5 Message Length ............................. 7-14

Matrix 2 of 5 ....................................................................... 7-15

Matrix 2 of 5 Message Length ..................................... 7-15

Code 11............................................................................... 7-16

Check Digits Required ................................................. 7-16

Code 11 Message Length ............................................. 7-17

Code 128............................................................................. 7-18

<GS> Substitution........................................................ 7-18

Code 128 Message Length ........................................... 7-19

Telepen .............................................................................. 7-20

Telepen Output............................................................. 7-20

Telepen Message Length.............................................. 7-20

UPC A................................................................................. 7-21

Check Digit .................................................................. 7-21

Number System............................................................ 7-21

UPC A, continued ........................................................ 7-22

Addenda ....................................................................... 7-22

Addenda Required........................................................ 7-22

Addenda Separator ....................................................... 7-23

UPC Strict Decoding.................................................... 7-23

UPC E0 and UPC E1 .......................................................... 7-24

UPC E Expand ............................................................. 7-24

Check Digit .................................................................. 7-25

Number System............................................................ 7-25

Addenda ....................................................................... 7-26

Addenda Required........................................................ 7-26

Addenda Separator ....................................................... 7-27

EAN/JAN 13....................................................................... 7-28

Check Digit................................................................... 7-28

Addenda........................................................................ 7-29

Addenda Required........................................................ 7-29

Addenda Separator ....................................................... 7-30

ISBN Enable................................................................. 7-30

EAN/JAN 8......................................................................... 7-31

Check Digit................................................................... 7-31

Addenda........................................................................ 7-32

Addenda Required........................................................ 7-32

Addenda Separator ....................................................... 7-33

MSI ..................................................................................... 7-34

MSI, continued ............................................................. 7-34

Check Character ........................................................... 7-34

MSI Message Length.................................................... 7-35

Plessey................................................................................. 7-36

Plessey Message Length............................................... 7-36

RSS-14 ................................................................................ 7-37

RSS Limited........................................................................ 7-37

RSS Expanded .................................................................... 7-38

RSS Expanded Message Length................................... 7-38

China Post Code.................................................................. 7-39

China Post Message Length ......................................... 7-39

PDF417 ............................................................................... 7-40

PDF417 Message Length ............................................. 7-40

Show GLI Blocks ........................................................ 7-41

Scan Diagnostics .......................................................... 7-41

PDF Learn Mode .......................................................... 7-42

MicroPDF417 .................................................................... 7-43

MicroPDF417............................................................... 7-43

MicroPDF417 Message Length.................................... 7-43

EAN•UCC Composite Symbology .................................... 7-44

EAN•UCC Composite ........................................................ 7-44

Enable UPC/EAN Version.................................................. 7-44

EAN•UCC Composite Code Message Length ............. 7-45

Chapter 8 - Cloning

Procedure .............................................................................. 8-1

Chapter 9 - Visual Menu

Visual Menu Introduction..................................................... 9-1

Temporary Visual Menu Configuration......................... 9-1

Installing Visual Menu from the Web............................ 9-1

Upgrading USB Firmware ............................................. 9-2

Chapter 10 - Interface Keys

Keyboard Function Relationships....................................... 10-1

Supported Interface Keys .................................................. 10-3

Chapter 11 - Utilities

To Add a Test Code I.D. Prefix to All Symbologies.......... 11-1

Show Software Revision..................................................... 11-1

Show Data Format .............................................................. 11-1

Specular Effect Reduction .................................................. 11-2

Chapter 12 - Serial Programming Commands

Conventions ........................................................................ 12-1

Menu Command Syntax ..................................................... 12-1

Query Commands......................................................... 12-2

Concatenation of Multiple Commands ........................ 12-2

Trigger Commands ............................................................. 12-4

Resetting the Factory Settings ............................................ 12-4

Menu Commands ............................................................... 12-5

PDF417 Wand Emulation ............................................ 12-7

Chapter 13 - Product Specifications

3800 Product Specifications ............................................... 13-1

3900 Product Specifications ............................................... 13-2

Standard Cable Pinouts....................................................... 13-3

vii

Chapter 14 - Maintenance

Repairs ................................................................................ 14-1

Maintenance........................................................................ 14-1

Replacing the Interface Cable ...................................... 14-2

Troubleshooting .................................................................. 14-2

Chapter 15 - Customer Support

Product Service and Repair................................................. 15-1

Online Product Service and Repair Assistance ............ 15-2

Technical Assistance........................................................... 15-2

Online Technical Assistance ........................................ 15-3

Limited Warranty ............................................................... 15-4

viii

1 - 2 3800/3900 User’s Guide

Unpacking the Scanner

Open the carton. The shipping carton or container should contain:

• Check to make sure everything you ordered is present.

• Save the shipping container for later storage or shipping.

• Check for damage during shipment. Report damage immediately to the

carrier who delivered the carton.

An 3800: or an 3900:

3800/3900 User’s Guide 1 - 3

3800 Scanner Identification

3900 Scanner Identification

www.handheld.com

Hand Held Products, Inc.

Made in USA

gepru fte

Si c her he i t

TUV

Rheinland

ProductSafety

E 153740

7D21

Input:

4.5-5.5VDC,

0-.3A

FOR HOME OR OFFICE USE

Tes ted to Comply With FC C S tandards

This Class B digital apparatus complies with Canadian

ICES-003. Cet appareil

numerique de la

Classe B est conforme a la

norme NMB-003 du Canada.

N10410

S ee m anua l for

P a te n t de tails .

Input:

4.5-5.5 VDC, 0-.3A

S ee m a nu al for

P atentdetails .

Made in USA

geprufte

Sicherheit

TUV

Rheinland

Product Safety

E 153740

7D21

Teste d toCompl yWithFCC Standa rds

FOR HOME OR OFFICE USE

Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada.

This Class B digit al apparatus complies wi th Canad ian ICES-003 .

N10410

Hand Held Products, Inc.

ww w.handheld.com

3900 Scanner

Bottom View

Input:

4.5-5.5 VDC, 0-.3A

S ee ma nual for

Pate nt de tails .

Made in USA

gep ruft e

S i ch erhe it

TUV

Rheinland

Product Safety

E 153740

7D21

Tes ted to C omply With FC C S tanda rds

FOR HOME OR OFFICE USE

Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada.

This Class B digital apparatus complies with Canadian ICES-003.

N 10410

Hand Held Products, Inc.

www.handheld.com

1 - 4 3800/3900 User’s Guide

Connecting the Scanner When Powered by Host

(Keyboard Wedge)

A scanner can be connected between the keyboard and PC as a “keyboard

wedge,” plugged into the serial port, or connected to a portable data terminal in

wand emulation or non decoded output mode. The following is an example of a

keyboard wedge connection:

1. Turn off power to the terminal/computer.

2. Disconnect the keyboard cable from the

back of the terminal/computer.

3. Connect the appropriate

interface cable to the

scanner and to the terminal/

computer.

4. Turn the terminal/computer

power back on. The scanner will beep twice.

5. Verify the scanner operation by scanning a bar code from the back cover of

this manual. The scanner will beep once.

Disconnect

3800/3900 User’s Guide 1 - 5

Mounting Information for the 3900

Aperture plane

1.52

.8 Optical center is ± 2" from horizontal.

(Angle begins at aperture plane.)

2˚ Ref typ

4.64

2.67 1.52 Ref

2.99

47.5˚

.89

.04

.700

M4 Inserts typ 3

Thread depth

4.7 mm (.185")

Cable Exit

1.3

.65

2.5

(13 mil and 15 mil)

3.5

(5 mil and 7.5 mil)

4.1

8.5

9.5

3 mil

5 mil

7.5 mil 13 mil

15 mil

23˚ typ

4.9

4.2

1.9

TYPICAL PERFORMANCE ON HIGH QUALITY SYMBOLS.

Note: Measurements are in inches.

1 - 6 3800/3900 User’s Guide

Mounting Information, continued

Specular Zone

The 3900 must be mounted at a 5 degree, or greater, angle to the bar code in

order to scan properly:

The scanner is now connected and ready to communicate with your terminal/PC.

You must program the scanner for your interface before bar code data can be

transmitted to your terminal/PC. If you are using the scanner as a keyboard

wedge, turn to page 2-1. If the scanner is connected via a serial port, turn to

page 2-8. If this is a wand emulation application, turn to page 2-15, and for a non

decoded output connection, turn to page 6-2.

Plug and Play

Plug and Play bar codes provide instant scanner set up for commonly used

interfaces.

Note: After you scan one of the codes, power cycle the host terminal to have the

interface in effect.

The most common interface is Keyboard Wedge. The following Keyboard

Wedge bar code also programs a carriage return (CR) suffix.

Keyboard Wedge Interface for IBM PC

AT and Compatibles

3800/3900 User’s Guide 1 - 7

The following Plug and Play bar code for IBM XT and Compatibles also

programs a carriage return (CR) suffix.

The following Plug and Play bar code for IBM PS-2 and Compatibles also

programs a carriage return (CR) suffix.

Use Non Decoded Output Laser Emulation when connecting to a secondary

terminal with integral decoding. This also sets the transmission rate to 36 scans

per second and the polarity to white high.

For most laptops, scanning the Laptop Direct Connect bar code allows

operation of the integral keyboard. The following Laptop Direct Connect bar

code also programs a carriage return (CR) suffix.

The RS-232 Interface bar code is used when connecting to the serial port of a

PC or terminal. The following RS-232 Interface bar code adds a suffix of a CR

and LF, and also programs the parameters:

Option Setting

Baud Rate 9600 bps

Parity Even

IBM XT and Compatibles

IBM PS-2 and Compatibles

Non Decoded Output

Laser Emulation

Laptop Direct Connect

1 - 8 3800/3900 User’s Guide

In Wand Emulation mode, the scanner decodes the bar code then sends data in

the same format as a wand scanner. The Same Code format transmits UPC,

EAN, Code 128 and Interleaved 2 of 5 bar codes without any changes, but

converts all other symbologies to Code 39.

The following Wand Emulation bar code sets the interface to Wand Emulation

mode and translates bar code data as Code 39 symbology. It also programs the

Transmission Rate to 25 inches per second, and Output Polarity to black high.

Note: For the 3800PDF model: When the 3800PDF interface is set to wand

emulation, all PDF417 bar code data is transmitted as Code 128. Data

from other symbologies follow the rules described above.

IBM 4683 Ports 5B, 9B, and 17 Interface

Note: The following Retail “Plug and Play” codes are for use with the 3800XX-

11 and 3800XX-11E models only.

Scan one of the following “Plug and Play” codes to program the 3800 for IBM

4683 Port 5B, 9B, or 17.

Data Format 7 data bits, parity bit, 1 stop bit (8 bit data)

Option Setting

RS-232 Interface

Wand Emulation Same Code

Wand Emulation (Code 39 Format)

1 - 10 3800/3900 User’s Guide

Note: After scanning one of these codes, you must re-boot the cash register.

Each bar code above also programs the following suffixes for each symbology:

Scan one of the following codes to program the 3800 for USB PC Keyboard or

USB Macintosh Keyboard.

Scan the following code to program the 3800 for USB HID bar code scanners.

Symbology Suffix

EAN 8 0C

EAN 13 16

UPC A 0D

UPC E 0A

Code 39 00 0A 0B

Interleaved 2 of 5 00 0D 0B

Code 128 00 18 0B

IBM SurePos (USB Handheld Scanner) Interface

IBM SurePos (USB Tabletop Scanner) Interface

USB Keyboard (PC)

USB Keyboard (Mac)

USB HID Bar Code Scanner

3800/3900 User’s Guide 1 - 11

OCIA Interface

Note: The OCIA interfaces are only available on the 3800XX-11 and 3800XX-

11E models.

Scan one of the following “Plug and Play” codes to program the 3800 for Generic

OCIA, NCR OCIA Short Format (8 bit), NCR OCIA Long Format (9 bit), and

Nixdorf OCIA.

Note: After scanning one of these codes, you must re-boot the cash register.

The Generic OCIA bar code also programs the following prefixes for each

symbology:

NCR OCIA Short Format (8 Bit) Interface

The NCR OCIA Short Format (8 Bit) bar code also programs the following

prefixes for each symbology:

Symbology Prefix

EAN 8 06 06

EAN 13 06

UPC A 01

UPC E 05

Symbology Prefix

EAN 8 0F 0F

EAN 13 0F

UPC A 0A

UPC E 0E

Generic OCIA Interface

NCR OCIA Short Format (8 Bit) Interface

1 - 12 3800/3900 User’s Guide

NCR OCIA Long Format (9 Bit) Interface

The NCR OCIA Long Format (9 Bit) bar code also programs the following

prefixes for each symbology:

Nixdorf OCIA Interface

The Nixdorf OCIA bar code also programs the following prefixes for each

symbology:

Serial Wedge

The 3800/3900 uses true and TTL signal levels to wedge into an RS-232 serial

network. Use 3800/3900 serial wedge cables only to prevent damage to the

scanner. Refer to the serial interface programming (pages 2-8 to 2-12) to set the

baud rate and communications protocol.

Symbology Prefix

EAN 8 46 46

EAN 13 46

UPC A 41

UPC E 45

Code 39 42 31

Interleaved 2 of 5 42 32

Code 128 42 33

Symbology Prefix

EAN/UPC with Addenda 44 4B

Code 39 44 49

Interleaved 2 of 5 44 48

2 of 5 44 47

Code 128 44 4A

NCR OCIA Long Format (9 Bit) Interface

Nixdorf OCIA Interface

3800/3900 User’s Guide 1 - 13

To set up the serial wedge terminal ID, find the terminal ID in the Supported

Terminal Chart and follow the instructions on page 2-2. Set the port to which you

want the scanned data to transmit. Port 1 corresponds to P1 on the output cable

and Port 2 corresponds to P2 on the output cable. Choosing Both sends

scanned data to P1 and P2. Default = P1.

* P1

Both P1 and P2

1 - 14 3800/3900 User’s Guide

3800/3900 User’s Guide 2 - 1

Terminal Interfaces

Keyboard Wedge Connection

3800/3900 scanners are factory programmed for a keyboard wedge interface to

an IBM PC AT with a USA keyboard. If this is your interface and you do not need

to modify the settings, skip to Chapter 3 - Output.

If you programmed the scanner for a different terminal interface and/or you want

to change to an IBM PC AT and Compatibles Keyboard Wedge interface, scan

the bar code below.

IBM PC AT and Compatibles

with CR suffix

2 - 2 3800/3900 User’s Guide

Terminal ID

If your interface is not a standard PC AT, refer to "Supported Terminals" on page

2-3 through page 2-4, and locate the Terminal ID number for your PC. Scan the

Terminal ID bar code below, then scan the numeric bar code(s) on the inside

back cover of this manual to program the scanner for your terminal ID. Scan

Save to save your selection.

For example, an IBM AT terminal has a Terminal ID of 003. You would scan the

Terminal ID bar code, then 0, 0, 3 from the inside back cover, then Save. If you

make an error while scanning the digits (before scanning Save), scan the

Discard code on the back cover, scan the Terminal ID bar code, scan the digits,

and the Save code again.

Note: After scanning one of these codes, you must power cycle your computer.

Terminal ID

Save

3800/3900 User’s Guide 2 - 3

Supported Terminals

Terminal Model(s) Terminal ID

Apple Mac Mac Classic, SE SE30, II (All) 049 **

Apple Mac Powerbook 5300 Series (Portable PC) 049 **

DEC VT510, 520, 525 (PC style) 005

DEC VT510, 520, 525 (DEC style

LK411) 104

Esprit 200, 400 005

Heath Zenith PC, AT 090

HP Vectra 003

HP Vectra ES 023

IBM XT 001

IBM PS/2 25, 30, 77DX2 002

IBM AT, PS/2 30–286, 50, 55SX, 60,

70, 70–061, 70–121, 80 003 *

IBM 102 key 3151, 3161, 3162, 3163, 3191,

3192, 3194, 3196, 3197, 3471,

3472, 3476, 3477

006

IBM 122 key 3191, 3192, 3471, 3472 007

IBM 122 key 3196, 3197, 3476, 3477, 3486,

3482, 3488

008

IBM 122 key 3180 024

IBM 122 key 3180 data entry keyboard 114

IBM DOS/V 106 key PC & Workstation 102

IBM SurePOS USB Handheld Scanner 128****

IBM SurePOS USB Tabletop Scanner 129****

IBM Thinkpad 360 CSE, 340, 750 097

IBM Thinkpad 106

IBM Thinkpad 365, 755CV 003

I/O 122 key 2676D, 2677C, 2677D 008

ITT 9271 007

Lee Data IIS 007

NEC 98XX Series 103

Olivetti M19, M200 001

Olivetti M240, M250, M290, M380,

P500 003

RS-232 True 000 ***

RS-232 TTL 000

Serial Wedge 050

Silicon Graphics Indy, Indigoll 005

2 - 4 3800/3900 User’s Guide

Telex 88 key 078, 078A, 79, 80, 191, 196,

1191,1192, 1471, 1472, 1476,

1477, 1483

025

Telex 88 key Data Entry Keyboard 112

Telex 102 key 078, 078A, 79, 80, 191, 196,

1191,1192, 1471, 1472, 1476,

1477, 1483

045

Telex 122 key 078, 078A, 79, 80, 191, 196,

1191,1192, 1471, 1472, 1476,

1477, 1482, 1483

046

USB converter 124

USB PC Keyboard 124 *****

USB Mac Keyboard 125

Wand Emulation 061

Default for -11, -12 models

** Applies to -12 models only

*** Default for -13 model (applies to -13 models only)

**** Applies to -15 model only. Because special suffixes are required

by the IBM SurePOS terminal, it is best to use the Plug and Play

bar codes on page 1-10 to program these interfaces, rather than

scanning the terminal ID listed in this table.

***** Default for -14, -15 models

Supported Terminals (Continued)

Terminal Model(s) Terminal ID

3800/3900 User’s Guide 2 - 5

Keyboard Country

Scan the Program Keyboard Country bar code below, then scan the numeric

bar code(s) from the inside back cover, then the Save bar code to program the

keyboard for your country. As a general rule, the following characters are not

supported by the scanner for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

Keyboard Style

This programs keyboard styles, such as Caps Lock and Shift Lock. Default =

Regular.

Regular

is used when you normally have the Caps Lock key off.

Caps Lock

is used when you normally have the Caps Lock key on.

Country Code Scan Country Code Scan

Belgium 1 Italy 5

Denmark 8 Norway 9

Finland 2 Spain 10

France 3 Switzerland 6

Germany/Austria 4 USA (Default) 0

Great Britain 7

Program Keyboard Country

Save

* Regular

Caps Lock

2 - 6 3800/3900 User’s Guide

Shift Lock

is used when you normally have the Shift Lock key on (not common

to U.S. keyboards).

Automatic Caps Lock

is used if you change the Caps Lock key on and off. The

software tracks and reflects if you have Caps Lock on or off (AT and PS/2 only).

This selection can only be used with systems that have an LED which notes the

Caps Lock status.

Emulate External Keyboard

should be scanned if you do not have an external

keyboard (IBM AT or equivalent). To connect the scanner to a laptop, it may be

necessary to use the Automatic Direct Connect selection on in page 2-7

conjunction with the bar code below.

Note: After scanning the Emulate External Keyboard bar code, you must power

cycle your computer.

Keyboard Modifiers

This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo

Mode.

Control + ASCII Mode On:

The scanner sends key combinations for ASCII

control characters for values 00-1F. Refer to page 10-1 for CTRL+ ASCII

Values. Default = Off

Shift Lock

Automatic Caps Lock

Emulate External Keyboard

Control + ASCII Mode On

* Control + ASCII Mode Off

3800/3900 User’s Guide 2 - 7

Turbo Mode:

The scanner sends characters to an IBM AT terminal faster. (For

use with IBM AT only.) If the terminal drops characters, do not use Turbo Mode.

Default = Off

Numeric Keypad Mode:

Sends numeric characters as if entered from a

numeric keypad. Default = Off

Automatic Direct Connect:

Use this selection if you are using a laptop whose

keyboard is disabled when you plug in the scanner. This selection can also be

used if you have an IBM AT style terminal and the system is dropping characters.

Default = Off

Turbo Mode On

* Turbo Mode Off

Numeric Keypad Mode On

* Numeric Keypad Mode Off

Automatic Direct

Connect Mode On

* Automatic Direct Connect

Mode Off

2 - 8 3800/3900 User’s Guide

Serial Port Connection

All communication parameters between the scanner and terminal must match for

correct data transfer through the serial port using RS-232 protocol. Scanning the

RS-232 interface bar code, programs the scanner for an RS-232 interface at

9600 baud, even parity, 7 data bits, 1 stop bit (8 bit data), and adds a suffix of a

CR LF.

1. Turn off power to the terminal/computer.

2. Connect the appropriate interface cable to

the scanner.

Note: For the scanner to work properly, you

must have the correct cable for your type

of terminal/computer.

3. Plug the serial connector into the serial port

on the back of your computer/terminal, as shown below. Tighten the two

screws to secure the connector to the port.

4. Plug the power pack into a power source.

5. Once the scanner has been fully connected, power up the terminal/

computer.

RS-232 Interface

3800/3900 User’s Guide 2 - 9

Baud Rate

Baud Rate sends the data from the scanner to the terminal at the specified rate.

The host terminal must be set for the same baud rate as the scanner.

Default = 9600.

300

2400

600

1200

4800

38400

* 9600

19200

2 - 10 3800/3900 User’s Guide

RS-232 Word Length: Data Bits, Stop Bits, and Parity

Data Bits

sets the word length at 7 or 8 bits of data per character. If an

application requires only ASCII Hex characters 0 through 7F decimal (text, digits,

and punctuation), select 7 data bits. For applications which require use of the full

ASCII set, select 8 data bits per character. Default = 7.

Stop Bits

sets the stop bits at 1 or 2. Default = 1.

Parity

provides a means of checking character bit patterns for validity.

Default = Even.

* 7 Data, 1 Stop, Parity Even

7 Data, 1 Stop, Parity Mark

7 Data, 1 Stop, Parity None

7 Data, 1 Stop, Parity Odd

7 Data, 1 Stop, Parity Space

7 Data, 2 Stop, Parity Odd

7 Data, 2 Stop, Parity Even

7 Data, 2 Stop Parity None

7 Data, 2 Stop, Parity Mark

3800/3900 User’s Guide 2 - 11

RS-232 Word Length: Data Bits, Stop Bits, and Parity

(continued)

8 Data, 1 Stop, Parity None

7 Data, 2 Stop, Parity Space

8 Data, 1 Stop, Parity Even

8 Data, 1 Stop, Parity Odd

8 Data, 1 Stop, Parity Mark

8 Data, 1 Stop, Parity Space

2 - 12 3800/3900 User’s Guide

RS-232 Handshaking

RS-232 handshaking is a set of rules concerning the exchange of data between

serially communicating devices. Default = RTS/CTS, XON/XOFF and ACK/

NAK Off

Wand Emulation Connection

In Wand Emulation mode, the scanner decodes the bar code then sends data in

the same format as a wand scanner. The Code 39 Format converts all

symbologies to Code 39. The Same Code Format transmits UPC, EAN, Code

128 and Interleaved 2 of 5 without any changes, but converts all other

symbologies to Code 39. These codes set the transmission rate to 25 inches per

second and the output polarity to black, high. Default = Code 39 Format.

RTS/CTS On

* XON/OFF Off

* RTS/CTS Off

XON/XOFF On

ACK/NAK On

* ACK/NAK Off

* Code 39 Format

Same Code Format

3800/3900 User’s Guide 2 - 13

Note: For the 3800PDF model: When the 3800PDF interface is set to wand

emulation, all PDF417 bar code data is transmitted as Code 128. Data

from other symbologies follow the rules described above.

Wand Emulation Transmission Rate

The Transmission Rate is limited by the terminal’s ability to receive data without

dropping characters. Default = 25 inches/second.

* 25

120

150

200

2 - 14 3800/3900 User’s Guide

Wand Emulation Polarity

The Polarity can be sent as standard with black bars high, or reversed with white

bars high. Default = Black High.

Wand Emulation Idle

The idle describes the state of the scanner when no data is being transmitted.

When in Wand Emulation mode, you must set the scanner’s idle state to match

the idle state for the device to which the scanner is connected. Default = Idle

High.

* Black High

White High

* Idle High

Idle Low

3800/3900 User’s Guide 2 - 15

PDF417 Wand Emulation

Note: The following Wand Emulation functions are for use with the 3800PDF-12

and 3800PDF-12E scanners only.

Data Block Size

This transmits the PDF417 data in smaller blocks to prevent buffer overflow.

Default = 60.

Delay Between Blocks

This sets the delay time between data blocks. Default = 50ms.

* 60

5ms

500ms

* 50ms

150ms

2 - 16 3800/3900 User’s Guide

Overall Checksum

When this option is turned on, a computed check character is added at the end

of the entire message. The check character is the character which when

Exclusive-OR’d with every preceding character of the message yields a result of

0x00 (00H). Default = Off.

* Off

3800/3900 User’s Guide 3 - 1

Output

Scan Rate

Adjusting the scan rate changes the current draw when scanning. The slower

the scan rate, the lower the current draw. (The standby current remains the

same.) Scan speeds are 270 s/s, 135 s/s, and 67 s/s. A scan speed of 270

draws the highest power and has the best performance. A scan speed of 135

has a medium draw with medium performance. A scan speed of 67 draws the

lowest power and has the lowest performance. Default = 270 s/s.

Beeper Volume

Default = High.

* 270 s/s

135 s/s

67 s/s

* High

Medium

Off

Low

3 - 2 3800/3900 User’s Guide

Beeper Tone

Default = Normal.

Scan Voting

This sets the number of times the same bar code has to be read before it is

transmitted to the terminal. Normal uses the default values listed for the

symbologies in the Default Charts beginning on page 12-5. High doubles the

votes used below the threshold. Default = Voting Normal.

Reduce Quiet Zone

Reducing the quiet zone requirements below AIM guidelines makes it possible to

read off-spec bar codes. This feature is effective with all symbologies. Default

= Don’t Reduce Quite Zone.

* Normal Beep

Short Beep

* Voting Normal

Voting High

* Don’t Reduce Quiet Zone

Reduce Quiet Zone

3 - 4 3800/3900 User’s Guide

Good Read Delay

This sets the minimum amount of time before the scanner can read another bar

code. Default = No Delay.

Trigger Mode

Manual/Serial Trigger:

You can activate the scanner either by pressing the

trigger, or using a serial trigger command (see "Trigger Commands" on page 12-

4). When in manual trigger mode, the scanner scans until a bar code is read, or

until the trigger is released.

When in serial mode, the scanner scans until a bar code has been read or until

the deactivate command is sent. In serial mode, the scanner can also be set to

turn itself off after a specified time has elapsed (see Serial Trigger Time Out,

which follows). Default for 3800 .

* No Delay

Short Delay

Medium Delay

Long Delay

Manual/Serial Trigger

3800/3900 User’s Guide 3 - 5

Serial Trigger Time Out:

Use this selection to set a time out (in quarter

seconds) of the scanner’s trigger when using serial commands to trigger the

scanner. Once the scanner has timed out, it must be triggered again either

serially or manually. After scanning the Serial Trigger Time Out bar code, set the

time out duration (from 0-1200 quarter seconds) by scanning digits from the

inside back cover, then scanning Save. Default = 0 (infinite, or no time out).

Manual Trigger, Low Power:

The scanner “sleeps,” using only 30 milliamps,

until the trigger is pulled. When the trigger is pulled, the scanner wakes up and

operates at reduced power until there is no triggering for the time set with the Low

Power Time Out bar code. There is a short delay in operation when the scanner

is first triggered, but there is no delay when operating in low power mode.

Note: Manual Trigger, Low Power cannot be used with keyboard wedge

applications.

Low Power Time Out:

Scan the Low Power Time Out bar code to change the

time out duration. Then scan the time out duration (from 0-300 seconds) from

the inside back cover, and Save. Default = 2 minutes.

Note: If you make an error while scanning the digits (before scanning Save),

scan Discard on the back cover, scan the Lower Power Time Out bar

code, scan the correct digits, then Save again.

Automatic Trigger:

The scanner scans continuously at full power. Default for

3900.

Serial Trigger Time Out

Manual Trigger, Low Power

Low Power Time Out

Automatic Trigger

3 - 6 3800/3900 User’s Guide

Presentation Mode:

The LEDs are off until a bar code is presented to the

scanner. Then the LEDs turn on automatically to read the code. Presentation

Mode uses normal office or store ambient light to detect the bar codes.

Note: Do not use Presentation Mode with a 3800/3900PDF. Normal office or

store ambient light does not provide enough illumination for the 3800/

3900PDF to work properly in Presentation Mode.

Presentation Mode

3800/3900 User’s Guide 4 - 1

Data Editing

Prefix/Suffix Overview

When a bar code is scanned, additional information is sent to the host computer

along with the bar code data. This group of bar code data and additional,

user-defined data is called a “message string.” The selections in this section are

used to build the user-defined data into the message string.

Prefix and Suffix characters are data characters that can be sent before and after

scanned data. You can specify if they should be sent with all symbologies, or

only with specific symbologies. The following illustration shows the breakdown

of a message string:

Points to Keep In Mind

• It is not necessary to build a message string. The selections in this chapter

are only used if you wish to alter the default settings. Default prefix = None.

Default suffix = None.

• A prefix or suffix may be added or cleared from one symbology or all

symbologies.

• You can add any prefix or suffix from the ASCII chart (page 4-6 ), plus Code

I.D. and Aim I.D.

• You can string together several entries for several symbologies at one time.

• Enter prefixes and suffixes in the order in which you want them to appear on

the output.

To Add a Prefix or Suffix:

Step 1. Scan the Add Prefix or Add Suffix symbol (page 4-4).

Step 2. Determine the 2 digit Hex value from the Symbology Chart (page 4-5)

for the symbology to which you want to apply the prefix or suffix.

Prefix Scanned Da atSuffix

1-10

alpha numeric

characters

variable length1-10

alpha numeric

characters

4 - 2 3800/3900 User’s Guide

Step 3. Scan the 2 hex digits from the Programming Chart inside the back

cover or scan 9 9, for all symbologies.

Step 4. Determine the hex value from the Decimal to Hex to ASCII Conversion

Chart (page 4-6) for the prefix or suffix you wish to enter.

Step 5. Scan the 2 digit hex value from the Programming Chart inside the back

cover.

Step 6. Repeat Steps 4 and 5 for every prefix or suffix character.

Step 7. To add the Code I.D., scan 5 C 8 0, , , .

To add AIM I.D., scan 5, C, 8, 1.

To add a backslash (\), scan 5 C 5 C, , , .

Step 8. Scan Save to exit and save, or scan Discard to exit without saving.

Repeat Steps 1-6 to add a prefix or suffix for another symbology.

Example: Add a Suffix to a specific symbology

To send a CR (carriage return)Suffix for UPC only:

Step 1. Scan Add Suffix.

Step 2. Determine the 2 digit hex value from the Symbology Chart (page 4-5)

for UPC.

Step 3. Scan 6, 3 from the Programming Chart (inside back cover).

Step 4. Determine the hex value from the Decimal to Hex to ASCII Conversion

Chart (page 4-6) for the CR (carriage return).

Step 5. Scan 0, D from the Programming Chart (inside back cover).

Step 6. Scan Save, or scan Discard to exit without saving.

To Clear One or All Prefixes or Suffixes:

You can clear a single prefix or suffix, or clear all prefixes/suffixes for a

symbology. When you Clear One Prefix (Suffix), the specific character you

select is deleted from the symbology you want. When you Clear All Prefixes

(Suffixes), all the prefixes or suffixes for a symbology are deleted.

Step 1. Scan the Clear One Prefix or Clear One Suffix symbol.

Step 2. Determine the 2 digit Hex value from the Symbology Chart (page 4-5)

for the symbology from which you want to clear the prefix or suffix.

Step 3. Scan the 2 digit hex value from the Programming Chart inside the back

cover or scan 9 9, for all symbologies.

Your change is automatically saved.

3800/3900 User’s Guide 4 - 3

To Add a Carriage Return Suffix to all Symbologies

Scan the following bar code if you wish to add a Carriage Return Suffix to all

symbologies at once. This action first clears all current suffixes, then programs

a carriage return suffix for all symbologies.

Add CR Suffix

All Symbologies

4 - 4 3800/3900 User’s Guide

Prefix Selections

Suffix Selections

Add Prefix

Clear One Prefix

Clear All Prefixes

Add Suffix

Clear One Suffix

Clear All Suffixes

Save

Discard

3800/3900 User’s Guide 4 - 5

Symbology Chart

Note:

Prefix/Suffix entries for specific symbologies override the universal (All

Symbologies, 99) entry.

Symbology Code

AIM

Hex

ID Symbology Code

AIM

Hex

China Postal q ]X0 71 Interleaved 2 of 5 e ]l0 65

Codabar a ]F0 61 Matrix 2 of 5 m ]X0 6D

Code 2 of 5 f ]S0 66 MicroPDF417 R ]L0 52

Code 11 h ]H0 68 MSI g ]M0 67

Code 39 b ]A0 62 PDF417 r ]L0 72

Code 32 PARAF

w ]X0 77 Plessey n ]P0 6E

Code 93 i ]G0 69 RSS-14 y ]e0 79

Code 128 j ]C0 6A Telepen t ]B0 74

EAN/JAN d ]E0 64 UPC c ]E0 63

EAN•UCC

Composite y ]e0 79 All Symbologies 99

IATA 2 of 5 f ]R0 66

4 - 6 3800/3900 User’s Guide

ASCII Conversion Chart (Code Page 1252)

Note: This table applies to U.S. style keyboards. Certain characters may differ

depending on your Country Code/PC regional settings.

Dec Hex Dec HexChar CharDec Hex Hex DecChar Char

0 @ ‘00 32 20 64NUL 40 96 60

1 ! A a01 33 21SOH 65 41 97 61

2 “ B b02 34 22STX 66 42 98 62

3 # C c03 35 23ETX 67 43 99 63

4 $ D d04 36 24EOT 68 44 100 64

5 % E e05 37 25ENQ 69 45 101 65

6 & F f06 38 26ACK 70 46 102 66

7 ‘ G g07 39 27BEL 71 47 103 67

8 ( H h08 40 28BS 72 48 104 68

9 ) l i09 41 29HT 73 49 105 69

10 0A LF 42 2A 74* 4A 6AJ 106 j

11 0B 43 2B 75VT + 4B 6BK 107 k

12 0C 44 2C 76FF , 4C 6CL 108 l

13 0D 45 2D 77CR - 4D 6DM 109 m

14 0E 46 2E 78SO . 4E 6EN 110 n

15 0F 47 2F 79SI / 4F 6FO 111 o

16 10 48 30 80DLE 0 50 70P 112 p

17 49 31 8111 DC1 1 51 71Q 113 q

18 12 50 32 82DC2 2 52 72R 114 r

19 13 51 33 83DC3 3 53 73S 115 s

20 14 52 34 84DC4 4 54 74T 116 t

21 15 53 35 85NAK 5 55 75U 117 u

22 16 54 36 86SYN 6 56 76V 118 v

23 17 55 37 87ETB 7 57 77W 119 w

24 18 56 38 88CAN 8 58 78X 120 x

25 19 57 39 89EM 9 59 79Y 121 y

26 1A 58 3A 90SUB : 5A 7AZ 122 z

27 1B 59 3B 91ESC ; 5B 7B[ 123 {

28 1C 60 3C 92FS < 5C 7C\ 124 |

29 1D 61 3D 93GS = 5D 7D] 125 }

30 1E 62 3E 94RS > 5E 7E^ 126 ~

31 1F 63 3F 95US ? 5F 7F_ 127

4 - 8 3800/3900 User’s Guide

Note: If you make an error while scanning the digits (before scanning Save),

scan

Discard

on the back cover, scan the Intercharacter Delay bar code,

scan the correct digits, and

Save

again.

To remove this delay, scan the Intercharacter Delay bar code, then set the

number of steps to 00. Scan the SAVE bar code from the inside back cover.

User Specified Intercharacter Delay

This is a delay of up to 495 milliseconds (in multiples of 5) placed after the

transmission of a particular character of scanned data. You can program up to

99 steps (of 5 ms each) to follow the character you specify. Scan the Delay

Length bar code below, then the number of steps for the delay, and the SAVE

bar code from the inside back cover.

Next, scan the Character to Trigger Delay bar code, then the 2 digit hex value for

the ASCII character that will trigger the delay (refer to the Decimal to Hex to

ASCII conversion chart on page 4-5).

Note: If you make an error while scanning the digits (before scanning Save),

scan Discard on the inside back cover, scan the Character to Trigger

Delay bar code, scan the correct digits, and Save again.

To remove this delay, scan the Delay Length bar code, and set the number of

steps to 00. Scan the SAVE bar code from the inside back cover.

1 2 3 4 5

Intercharacter Delay

Prefix Scanned Data Suffix

Intercharacter Delay

Delay Length

Character to Trigger Delay

3800/3900 User’s Guide 4 - 9

Interfunction Delay

This is a delay of up to 495 milliseconds (in multiples of 5) placed between the

transmission of each segment of the message string. You can program up to 99

steps (of 5 ms each). Scan the Interfunction Delay bar code below, then scan

the number of steps, and the SAVE bar code from the inside back cover.

Note: If you make an error while scanning the

digits (before scanning Save), scan Discard on the inside back cover,

scan the Interfunction Delay bar code, scan the correct digits, and Save

again.

To remove this delay, scan the Interfunction Delay bar code, then set the number

of steps to 00. Scan the SAVE bar code from the inside back cover.

Intermessage Delay

This is a delay of up to 495 milliseconds (in multiples of 5) placed between each

scan transmission. You can program up to 99 steps (of 5 ms each). Scan the

Intermessage Delay bar code below, then scan the number of steps, and the

SAVE bar code from the inside back cover.

Note: If you make an error while scanning the digits (before scanning Save),

scan Discard on the inside back cover, scan the Intermessage Delay bar

code, scan the correct digits, and Save again.

To remove this delay, scan the Intermessage Delay bar code, then set the

number of steps to 00. Scan the SAVE bar code from the inside back cover.

Interfunction Delays

Prefix Scanned Data Suffix

1 2 3 4 5STX HT CR LF

Interfunction Delay

2nd Scan Transmission1st Scan Transmission

Intermessage Delay

4 - 10 3800/3900 User’s Guide

3800/3900 User’s Guide 5 - 1

Data Formatting

Data Format Editor Introduction

The Data Format Editor selections are used to edit scanned data. For example,

you can use the Data Format Editor to insert characters at certain points in bar

code data as it is scanned. It is not necessary to use the Data Format Editor. A

set of defaults for the data format is already programmed in the scanner. The

selections in the following pages are used only if you wish to alter the default

settings. Default Data Format setting = None.

Normally, when you scan a bar code, it gets outputted automatically; however

when you do a format, you must use a “send” command (see Send Commands

on page 5-2) within the format program to output data.

Multiple formats may be programmed into the imager. They are stacked in the

order in which they are entered. However, the following list presents the order

in which formats are applied:

1. Specific Term ID, Actual Code ID, Actual Length

2. Specific Term ID, Actual Code ID, Universal Length

3. Specific Term ID, Universal Code ID, Actual Length

4. Specific Term ID, Universal Code ID, Universal Length

5. Universal Term ID, Actual Code ID, Actual Length

6. Universal Term ID, Actual Code ID, Universal Length

7. Universal Term ID, Universal Code ID, Actual Length

8. Universal Term ID, Universal Code ID, Universal Length

If you have changed data format settings, and wish to clear all formats and return

to the defaults, scan the Default Data Format code on page 5-4.

To Add a Data Format

Step 1. Scan the Enter Data Format symbol (page 5-4).

Step 2. Primary/Alternate Format

Determine if this will be your primary data format, or one of 3 alternate

formats. (Alternate formats allow you “single shot” capability to scan

one bar code using a different data format. After the one bar code has

been read, the scanner reverts to the primary data format. See page 5-

5.) If you are programming the primary format, scan 0. If you are pro-

gramming an alternate format, scan 1 2, , or 3, depending on the alter-

nate format you are programming.

Step 3. Terminal Type

Refer to the Supported Terminals Chart (page 2-3) and locate the Ter-

minal ID number for your PC. Scan three numeric bar codes on the

inside back cover to program the scanner for your terminal ID (you must

enter 3 digits). For example, scan 0 0 3 for an AT wedge.

3800/3900 User’s Guide 5 - 3

F4 Send “xx” character “nn” times (Insert) leaving cursor in current cursor posi-

tion.

Syntax = F4xxnn

(xx stands for the hex value for an ASCII code, see

Decimal to Hex to ASCII Conversion chart, page 4-6, and nn is the numeric

value (00-99) for the number of times it should be sent.)

E9 Send all but the last “nn” characters, starting from the current cursor posi-

tion.

Syntax = E9nn

(nn is the numeric value (00-99) for the number of

characters that will not be sent at the end of the message.)

Move Commands

F5 Move the cursor ahead “nn” characters from current cursor position.

Syntax = F5nn

(nn stands for the numeric value (00-99) for the number of

characters the cursor should be moved ahead.)

F6 Move the cursor back “nn” characters from current cursor position.

Syntax = F6nn

(nn stands for the numeric value (00-99) for the number of

characters the cursor should be moved back.)

F7 Move the cursor to the beginning of the data string.

Syntax = F7

EA Move the cursor to the end of the data string.

Syntax = EA

Search Commands

F8 Search ahead for “xx” character from current cursor position, leaving cursor

pointing to “xx” character.

Syntax = F8xx

(xx stands for the hex value for

an ASCII code, see Decimal to Hex to ASCII Conversion chart, page 4-6.)

F9 Search back for “xx” character from current cursor position, leaving cursor

pointing to “xx” character.

Syntax = F9xx

(xx stands for the hex value for

an ASCII code, see Decimal to Hex to ASCII Conversion chart, page 4-6.)

E6 Search ahead for the first non “xx” character from the current cursor posi-

tion, leaving cursor pointing to non “xx” character.

Syntax = E6xx

(xx

stands for the hex value for an ASCII code, see Decimal to Hex to ASCII

Conversion chart, page 4-6.)

E7 Search back for the first non “xx” character from the current cursor position,

leaving cursor pointing to non “xx” character.

Syntax = E7xx

(xx stands for

the hex value for an ASCII code, see Decimal to Hex to ASCII Conversion

chart, page 4-6.)

Miscellaneous Commands

FB Suppress all occurrences of up to 15 different characters, starting at the cur-

rent cursor position, as the cursor is advanced by other commands. When

the FC command is encountered, the suppress function is terminated. The

cursor is not moved by the FB command. Syntax = FBnnxxyy . .zz where

nn is a count of the number of suppressed characters in the list and xxyy ..

zz is the list of characters to be suppressed. (xx stands for the hex value for

an ASCII code, see Decimal to Hex to ASCII Conversion chart, page 4-6.)

FC Disables suppress filter and clear all suppressed characters.

Syntax = FC

E4 Replaces up to 15 characters in the data string with user specified charac-

ters. Replacement continues until the E5 command is encountered.

Syn-

tax = E4nnxx1xx2yy 1

yy2...zz1zz2

where nn is the total count of both

characters to be replaced plus replacement characters; xx

1 defines charac-

5 - 4 3800/3900 User’s Guide

ters to be replaced and xx2 defines replacement characters, continuing

through zz1 and zz2.

E5 Terminates character replacement.

Syntax = E5

FE Compare character in current cursor position to the character “xx.” If char-

acters are equal, increment cursor. If characters are not equal, no format

match.

Syntax = FExx

(xx stands for the hex value for an ASCII code, see

Decimal to Hex to ASCII Conversion chart, page 4-6.)

EC Check to make sure there is an ASCII number at the current cursor position.

If character is not numeric, format is aborted.

Syntax = EC

ED Check to make sure there is a non-numeric ASCII character at the current

cursor position. If character is numeric, format is aborted.

Syntax = ED

Data Format Editor

Enter Data Format

Default Data Format

Clear One Data Format

Save

Discard

Clear All Data Formats

3800/3900 User’s Guide 6 - 1

Secondary Interface

By switching interface cables, the 3800/3900 scanner can communicate with a

portable data terminal (secondary interface), in addition to the host terminal

(primary interface).

Note: Secondary interfaces do not apply to the 3800XX-15.

The secondary interface can be programmed at any time.

Secondary Code 39 Wand Emulation

In Wand Emulation mode, the scanner decodes the bar code then sends data in

the same format as a wand scanner. The Code 39 Format converts all

symbologies to Code 39. The Same Code Format transmits UPC, EAN, Code

128 and Interleaved 2 of 5 without any changes, but converts all other

symbologies to Code 39. These codes set the transmission rate to 25 inches per

second and the output polarity to black, high. Default = Code 39 Format.

Note for the 3800PDF model: When the 3800PDF interface is set to wand

emulation, all PDF417 bar code data is transmitted as Code 128. Data from

other symbologies follow the rules described above.

Secondary RS-232 Connection

All communication parameters between the scanner and terminal must match for

correct data transfer through the serial port using RS-232 protocol.

RS-232 programmable selections are used by both the primary and secondary

interfaces. Changing an RS-232 parameter (e.g., baud rate or parity), while in

primary or secondary mode will affect both interfaces.

* Wand Emulation

Code 39 Format

Wand Emulation

Same Code Format

RS-232 Interface

3800/3900 User’s Guide 6 - 3

Non Decoded Laser Emulation Idle

The idle describes the state of the scanner when no data is being transmitted.

When in Non Decoded mode, you must set the scanner’s idle state to match the

idle state for the device to which the scanner is connected. Default = High.

Disabling the Secondary Interface

You can temporarily disable the secondary interface, but still retain the

secondary interface settings in the scanner’s memory by scanning the Disable

bar code below. To re-enable the secondary interface, scan the Enable bar

code. Default =Disable.

Secondary Trigger Mode

Manual Trigger:

You must press the scanner trigger to scan. When not

scanning, idle power is maintained. Default = Manual Trigger.

Low

* High

* Disable

Enable

* Manual Trigger

6 - 4 3800/3900 User’s Guide

Automatic Trigger:

The scanner scans continuously at full power.

Manual Trigger, Low Power:

The scanner “sleeps,” using only 30 milliamps,

until the trigger is pulled. When the trigger is pulled, the scanner wakes up and

operates at normal power until there is no triggering for the time set with the Low

Power Time Out bar code. Then, the scanner goes to “sleep” again.

Low Power Time Out:

Scan the Low Power Time Out bar code to change the

time out duration. Then scan the time out duration (from 0-300 seconds) from

the inside back cover and Save. Default = 2 minutes.

Note: If you make an error while scanning the digits (before scanning Save),

scan Discard on the back cover, scan the Low Power Time Out bar code,

scan the correct digits, and Save again.

Note: The Secondary Manual Trigger, Lower Power option is not available on

the 3800XX-11 and 3800 Non-Decoded Out Laser XX-11E in Secondary

Emulation Mode.

Automatic Trigger

Manual Trigger, Low Power

Low Power Time Out

3800/3900 User’s Guide 7 - 1

Symbologies

Introduction

Use this section to program the scanner for Industrial, Retail, and PDF417

Symbology selections.

This programming section contains the following menu selections:

All Symbologies

If you want to decode all the symbologies allowable for your scanner, scan the

All Symbologies On

code.

• All Symbologies • IATA Code 2 of 5

• China Post Code • Interleaved 2 of 5

• Codabar • Matrix 2 of 5

• Code 2 of 5 • MicroPDF417

• Code 11 • MSI

• Code 39 • PDF417

• Code 32 PARAF • Plessey

• Code 93 • RSS-14

• Code 128 • Telepen

• EAN/JAN • UPC

• EAN•UCC Composite

All Symbologies On

All Symbologies Off

7 - 2 3800/3900 User’s Guide

Message Length Description

You are able to set the valid reading length of some of the bar code symbologies.

If the data length of the scanned bar code doesn’t match the valid reading length,

the imager will issue an error beep. You may wish to set the same value for

minimum and maximum length to force the imager to read fixed length bar code

data. This helps reduce the chances of a misread.

EXAMPLE: Decode only those bar codes with a count of 9-20 characters.

Min. length = 09 Max. length = 20

EXAMPLE: Decode only those bar codes with a count of 15 characters.

Min. length = 15 Max. length = 15

For a value other than the minimum and maximum message length defaults,

scan the bar codes included in the explanation of the symbology, then scan the

digit value of the message length and Save bar codes on the Programming Chart

inside the back cover of this manual. The minimum and maximum lengths and

the defaults are included with the respective symbologies.

7 - 18 3800/3900 User’s Guide

Code 128

Code 128

<GS> Substitution

When enabled, the scanner substitutes a <GS> for Function Character 1 when

decoding EAN 128. Default =Off.

* On

Off

* Off

Produktspezifikationen

Marke:	Honeywell
Kategorie:	Barcode-Leser
Modell:	3800g

Brauchst du Hilfe?

Wenn Sie Hilfe mit Honeywell 3800g benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Barcode-Leser Honeywell

Honeywell 7800LWN Bedienungsanleitung

6 Oktober 2024

Honeywell Dolphin 99EX Bedienungsanleitung

3 Oktober 2024

Honeywell ScanPal EDA50K Bedienungsanleitung

13 September 2024

Honeywell ScanPal EDA51K Bedienungsanleitung

28 August 2024

Honeywell MS3580 Quantum T Bedienungsanleitung

22 August 2024

Honeywell ScanGlove IS4225 Bedienungsanleitung

12 August 2024

Honeywell Dolphin 7900 Bedienungsanleitung

8 August 2024

Honeywell Dolphin 9950 Bedienungsanleitung

6 August 2024

Honeywell Youjie HF600 Bedienungsanleitung

6 August 2024

Honeywell ScanPal EDA60K Bedienungsanleitung

6 August 2024

Bedienungsanleitung Barcode-Leser

Neueste Bedienungsanleitung für -Kategorien-

Datalogic DSM0422 Bedienungsanleitung

30 November 2024

Datalogic Skorpio X5 Bedienungsanleitung

30 November 2024

Renkforce 7A CR6307A Bedienungsanleitung

3 Oktober 2024

Datalogic MGL8500X Bedienungsanleitung

23 September 2024

IFM O2I501 Bedienungsanleitung

22 September 2024

Datalogic Matrix 120 Bedienungsanleitung

13 September 2024

Datalogic Joya Touch Plus Bedienungsanleitung

12 September 2024

Posiflex CD-3602U Bedienungsanleitung

6 September 2024

Posiflex CD-3202U Bedienungsanleitung

6 September 2024

Brady IRX200 Bedienungsanleitung

6 September 2024