Hobart 6614 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hobart 6614 (12 Seiten) in der Kategorie Säge . Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/12
FORM 34527 Rev. B (August 2011)
MODEL 6614 MEAT SAW
MODEL
6614 ML-134096
PREVIOUS MODELS COVERED BY THIS MANUAL:
6614 ML-134050
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com
– 2 –
Installation, Operation, and Care of
MODEL 6614 MEAT SAW
SAVE THESE INSTRUCTIONS
GENERAL
The 6614 Meat Saw is rugged, durable, and easy to clean. The saw is equipped with a water resistant
3 HP electric motor and direct gear drive transmission that provides a blade speed of 3500 feet per minute.
The carriage (Fig. 1) has stainless steel ball bearings providing easy travel and dependability. The shaped
front edge of the carriage is comfortable to the operator's body even when leaned on during movement.
The carriage lock is standard. The upper pulley cover and bafe are stainless steel.
Table, carriage, pulleys, guides, and wiper assemblies can be quickly removed without tools for ease of
cleaning. Moving parts are enclosed but accessible. The blade is guarded above and below the cutting
zone. The pusher plate is provided to eliminate the need of handling items close to the blade; it can ride
on the right "anged-end" of the carriage so you keep your hands away from the cutting edge of the blade.
For electrical speciîš¿cations above 250 volts, a transformer provides a 115 volt control circuit voltage.
One long-life blade is furnished with each saw as standard equipment. This blade cannot be re-sharpened;
replacement blades are available through your local Hobart Service Ofîš¿ce.
© HOBART, 1995, 2000
PL-41501-1
UPPER PULLEY COVER
COLUMN GUARD
GAUGE PL EAT
TABLE (RIGHT)
GAUGE PL E HANDLEAT
LOCK LEVER
LOWER COVER (SCRAP N)PA
LEGS
FEET
CARRIAGE LOCK
CARRIAGE
TABLE (LEFT) SAW BLADE
UPPER GUIDE AND GUARD
SWITCH KNOB
Fig. 1
– 3 –
INSTALLATION
UNPACKING AND ASSEMBLY
Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found
to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
Prior to installation, test the electrical service to make sure it agrees with the speciîš¿cations on the machine
data plate located on the column.
Packed in a packet attached to the table compartment are the pusher plate and the gauge plate handle.
Place the pusher plate in its storage location under the carriage support (Fig. 2). Assemble the gauge
plate handle to the gauge plate support by screwing the stud into the threaded hole (Fig. 3).
LEVELING
Place the saw in its operating location. Using a spirit level, level the meat saw front-to-back and side-to-
side by turning the threaded feet in or out.
PL-52107
Hand Knob
Upper Guide
and Guard
PL-41502-1
CARRIAGE
SUPPORT
SAW BLADE
CARRIAGE
PUSHER PL EAT
HAND KNOB
PL-41503-1
GAUGE PL E HANDLEAT
Disconnect the electrical power to the machine and follow lockout / tagout
procedures.
SAW BLADE
The saw blade must be installed so the teeth point to the right
and down (Fig. 4).
UPPER GUIDE AND GUARD ASSEMBLY
When the saw is off, the hand knob (Fig. 4) can be used to raise
or lower the upper guide and guard assembly so the cutting
zone is only as high as necessary for the piece being cut. The
hand knob is not loosened during raising or lowering — it should
remain tightly secure.
Fig. 2 Fig. 3
Fig. 4
Produktspezifikationen
| Marke: | Hobart |
| Kategorie: | Säge |
| Modell: | 6614 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Hobart 6614 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Säge Hobart
23 September 2023
23 September 2023
Bedienungsanleitung Säge
- Säge Panasonic
- Säge Cotech
- Säge Makita
- Säge Bosch
- Säge Parkside
- Säge Vonroc
- Säge AEG
- Säge Powerfix
- Säge Black And Decker
- Säge Cocraft
- Säge FERM
- Säge Ryobi
- Säge Skil
- Säge Trotec
- Säge Hilti
- Säge Bort
- Säge DeWalt
- Säge Einhell
- Säge Elu
- Säge Festool
- Säge Mafell
- Säge Triton
- Säge Worx
- Säge Tacklife
- Säge Hikoki
- Säge Hitachi
- Säge Hyundai
- Säge Hazet
- Säge Kress
- Säge Metabo
- Säge Stanley
- Säge Kärcher
- Säge Atika
- Säge Güde
- Säge Power Craft
- Säge Scheppach
- Säge Bébé Confort
- Säge Workzone
- Säge Meec Tools
- Säge Dremel
- Säge Fieldmann
- Säge King Craft
- Säge Westfalia
- Säge Remington
- Säge Husqvarna
- Säge Stihl
- Säge Chicago Pneumatic
- Säge Dedra
- Säge Graphite
- Säge Snow Joe
- Säge Silverline
- Säge Holzmann
- Säge Sthor
- Säge Florabest
- Säge Hecht
- Säge Herkules
- Säge Stiga
- Säge Ford
- Säge Zipper
- Säge Yato
- Säge Baumr-AG
- Säge Greencut
- Säge Genesis
- Säge Evolution
- Säge Dolmar
- Säge Bavaria
- Säge Milwaukee
- Säge Narex
- Säge Toolcraft
- Säge Fein
- Säge Craftsman
- Säge Powerplus
- Säge Alpha Tools
- Säge McCulloch
- Säge Ozito
- Säge Yard Force
- Säge Sun Joe
- Säge Draper
- Säge Solo
- Säge Texas
- Säge Ridgid
- Säge Porter-Cable
- Säge Guede
- Säge Felisatti
- Säge Gardenline
- Säge Grizzly
- Säge Homelite
- Säge HURRICANE
- Säge Plantiflor
- Säge Qualcast
- Säge Shindaiwa
- Säge Sterwins
- Säge Tanaka
- Säge Troy-Bilt
- Säge Meister Craft
- Säge Sovereign
- Säge Challenge
- Säge Challenge Xtreme
- Säge Truper
- Säge MacAllister
- Säge RIKON
- Säge Pro-Cut
- Säge Selion
- Säge Kreg
- Säge Proviel
- Säge Merox
- Säge Bullcraft
- Säge XU1
- Säge MTM
- Säge Urrea
- Säge EFA
- Säge MyTool
- Säge Ergotools Pattfield
- Säge IKRA
- Säge FIXIT
- Säge Bavaria By Einhell
- Säge Rona
- Säge Donau Elektronik
Neueste Bedienungsanleitung für -Kategorien-
14 August 2024
7 August 2024
28 Juni 2024
28 Juni 2024
28 Juni 2024
28 Juni 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024