HGST UltraStar 7K4000 Bedienungsanleitung

HGST Festplatte UltraStar 7K4000

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für HGST UltraStar 7K4000 (3 Seiten) in der Kategorie Festplatte. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

Page 1 version 1.0

Quick Installation Guide

HGST Ultrastar 7K 000 4

Models: HUS 4040 0 72 ALE64

S 4 0 HU 72 030ALE64

S 4 0 HU 72 020ALE64

NOTE: The Deskstar 7K4000 & 5K4000 hard drives

feature Advanced Format technology. Advanced Format

increases the physical sector size on hard drives from

512 bytes to 4096 (4K) bytes, which increases drive

capacities and improves error correction capabilities.

Please consult the HGST Advanced Format Drives page

on our website for more information on using these hard drives.

System Requirements for Serial ATA

The following are needed to install a Serial ATA

(SATA) drive to a system:

•

•• SATA capable motherboard or controller card

•

•• SATA hard drive

•

•• SATA cable (1 meter or less in length)

Handling precautions

 Set the drive down gently to prevent damage

from impact or vibration.

 Do not open the ESD bag containing the drive

until needed.

 Handle the drive carefully by the edges. Do not

touch the exposed printed circuit board or any

electronic components.

 Do not press on the top or bottom of the drive.

 Before handling the drive, discharge any static

electricity from yourself and your clothing. With

one hand, touch an unpainted metal surface on

your computer chassis, then touch the ESD bag

with the other hand. Remain in contact with the

chassis and the bag for a minimum of two

seconds.

Quick installation procedure

Note: Back up all data before installing drive.

1. Turn off the computer.

2. Unplug the computer.

3. Remove the computer cover as instructed by

the computer system manual.

4. Discharge static electricity (see Handling

precautions).

5. Note the mounting position of existing drives

and cables. If you are replacing a drive or any

cable, remove it now.

6. Remove the drive from the ESD bag.

7. Record the model, the part number, and the

serial number of the drive for future reference.

8. Attach the Serial ATA cable to the drive. Match

key on cable to connector on drive

Mounting instructions

Note: The mounting hole and connector locations are

shown in figures 1 and 2.

1. Mount the drive securely.

2. Verify all attachments.

3. Replace the computer cover.

4. Plug in the computer.

5. Turn on the computer.

6. Verify that the hard disk is recognized by the

BIOS. Instructions for accessing your BIOS

can be found in the computer system manual

or in the motherboard manufacturer

documentation. If the drive is not recognized in

the BIOS, check the following:

HGST, a Western Digital company

Page 2 version 1.0

1) Auto Detect is enabled for the port the hard

disk is connected to.

2) SATA and power cables are connected

securely and not damaged.

3) The latest BIOS version is loaded onto the

system.

7. Many factors must be considered in order to

take advantage of the full capacity of drives

>2.2TB. Some configurations offer a higher

likelihood of success. Please refer to our

High Capacity Technology Brief and visit

our Above 2TB web page at

http://www.hitachigst.com/internal-

drives/above-2tb.

8. Your operating system setup utility will provide

instructions on how to partition and format your

drive before it installs the operating system.

For additional information see:

www.hitachigst.com/support

Note: The hard supportdrive s 6Gbps, 3Gbps and

1.5Gbps interface speeds. Higher interface speeds

are gated by Host Bus Adapter (HBA) or SATA

chipset of the system.

Mounting Recommendations

The drive will operate in all axes (6 directions).

Performance and error rate will stay within

specification limits if the drive is operated in the other

orientations from which it was formatted.

For reliable operation, the drive must be mounted in

the system securely enough to prevent excessive

motion or vibration of the drive during seek operation

or spindle rotation, using appropriate screws or

equivalent mounting hardware.

The recommended mounting screw torque is 0.6 - 1.0

Nm (6- 10 Kgf.cm).

The recommended mounting screw depth is 4 mm

maximum for bottom and 4.5 mm maximum for

horizontal mounting.

Drive level vibration test and shock test are to be

conducted with the drive mounted to the table using

the bottom four screws.

Thread (1) (2) (3) (4) (5) (6) (7)

6- 32UNC 41.28±0.5 44.45±0.2 95.25±0.2 6.35±0.2 28.5±0.5 60.0±0.2 41.6±0.2

Figure 1: Mounting holes locations (all dimensions are in mm)

Figure 2:

Connector location (all dimensions are in mm)

Interface connector

HGST, a Western Digital company

Page 3 version 1.0

HGST, a Western Digital company

3403 Yerba Buena Road

San Jose, CA 95135

Capacity notice: One GB is equal to one billion bytes and one TB equals 1,000

GB (one trillion bytes) when referring to hard drive capacity. Accessible capacity

will vary from the stated capacity due to formatting and partitioning of the hard

drive, the computer’s operating system, and other factors.

Ultrastar is a trademark of HGST, a Western Digital company

HGST trademarks are authorized for use in countries and jurisdictions in which

HGST has the right to use, market and advertise the brands. shall not be HGST

liable to third parties for unauthorized use of HGST trademarks.

Western Digital, WD, and the WD logo are registered trademarks of Western

Digital Technologies, Inc. All other trademarks are properties of their respective

owners.

References in this publication to products, programs or services do not HGST

imply that intends to make these available in all countries in which it HGST

operates. Some countries have laws that may affect encryption enabled devices. -

HGST assumes no responsibility for compliance with laws that apply to our

products after they are sold or outside of our control. Accordingly, we suggest

that you review all laws of the countries where you conduct business.

Product specifications provided are sample specifications and do not constitute a

warranty. Information is true as of the date of publication and is subject to

change. Actual specifications for unique part numbers may vary. Please visit the

Support section of our website, www.hgst.com/support, for additional information

on product specifications. Photographs may show design models.

3 April 2012

Produktspezifikationen

Marke:	HGST
Kategorie:	Festplatte
Modell:	UltraStar 7K4000
Breite:	101.6 mm
Tiefe:	147 mm
Gewicht:	690 g
Höhe:	26.1 mm
Betriebstemperatur:	5 - 60 °C
Eingebaut:	Ja
Schnittstelle:	Serial ATA III
Mittlere Betriebsdauer zwischen Ausfällen (MTBF):	2000000 h
Arbeitsspannung:	5 / 12 V
HDD Kapazität:	4000 GB
HDD Geschwindigkeit:	7200 RPM
HDD Größe:	3.5 "
Datenübertragungsrate:	6 Gbit/s
Puffergröße Speicherlaufwerk:	64 MB
HDD Übertragungsrate:	600 Mbit/s
Vibrationen in Betrieb:	0.67 G
Bytes pro Sektor:	512
Durchschnittliche Suchzeit:	8 ms
Stoßfestigkeit in Betrieb:	70 G
Stoßfestigkeit außer Betrieb:	300 G