Heatit Z-Smoke Bedienungsanleitung

Heatit Rauchmelder Z-Smoke

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Heatit Z-Smoke (6 Seiten) in der Kategorie Rauchmelder. Dieser Bedienungsanleitung war für 25 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/6

1. INTRODUCTION

Heatit Z-Smoke Detector is a multifunctional smoke sensor with a

built-in PIR motion sensor, temperature sensor and emergency light.

Heatit Z-Smoke Detector is a wireless operated photoelectronic smoke

detector designed to interact with most Z-Wave enabled controllers.

The detector features smoke-, temperature-, and IR-detection.

2. STATEMENT REGARDING PRODUCTS FROM MULTIPLE

MANUFACTURERS

Please read this before installation

This device may be used with all devices certiﬁed with the Z-Wave

Plus™ certiﬁcate and should be compatible with such devices

produced by any manufacturer. Every primary controller is diﬀerent

depending on the manufacturer, their target audience and intended

use/application. Please review the functionalities implemented by the

primary controller you intend to use with our Z-Wave Plus certiﬁed

device to ensure that it provides the necessary controls to take full

advantage of our product’s capabilities.

3. BEHAVIOR WITHIN THE Z-WAVE™ NETWORK

This device may be operated within any Z-Wave network with

Z-Wave-certiﬁed devices from other manufacturers. All non-battery-

operated nodes within the network will act as repeaters regardless of

manufacturer to increase the reliability of the network. On delivery, the

device does not belong to any Z-Wave network.

The device needs to be added to an existing network to communicate

with the other devices within it. Devices may also be removed from

a network. The add/remove processes are initiated by the primary

controller of the Z-Wave network.

4. QUICK START

1. Unscrew the battery cover.

2. Insert three 3V CR123 Lithium batteries into the battery

compartment.

3. Orient the batteries according to the polarity.

4. The device will enter auto inclusion mode after being powered on.

5. Set the primary controller in add mode (security/non-security).

6. The Heatit Z-Smoke Detector is now included in your Z-Wave

network.

5. INSTALLATION/MOUNTING

1. Place the smoke detector at the desired mounting location

and use the Range Test function to make sure the smoke

detector can be detected by the control panel where it has been

placed.

2. A mounting sheet is included in the package. The illustration size

equals the smoke detector’s actual size and the perforated design

allows for easy removal after installation.

3. Position the sheet tightly against the ceiling and use the four holes as

a template to drill holes and insert wall plugs in the wall/ceiling if so

required.

4. Place the mounting bracket on top of the mounting sheet and screw

it onto the wall/ceiling.

TABLE OF CONTENTS

1 Introduction

2 Statement regarding products from multiple manufacturers

3 Behavior within the Z-Wave™ network

4 Quick Start

5 Installation/Mounting

6 Add/Remove

7 LED-indicator /Function button

8 Factory Reset

9 Testing the smoke detector

10 Alarm silence

11 Calibration

12 Serial connection

13 Security

14 Node Information Frame

15 Command Classes

15.1 Command Class Notiﬁcation V8

15.2 Command Basic

15.3 Command Class Sensor Multilevel V11

15.4 Command Class Battery V1

16 Associations

17 Association Groups

18 Product information

HEATIT

Z-SMOKE

DETECTOR Ver 2020-A

Firmware 4.02

01.10.2020

Installers manual

BATTERY

5. The smoke detector has four notches on its back cover. Gently align

the four notches on the smoke detector with the hooks on the

mounting bracket. Rotate clockwise to lock the hook.

6. Installation is now complete. You may now tear oﬀ the mounting

sheet.

a. LED-indicator/function button/emergency light.

b. IR-lens.

c. Buzzer.

d. Battery compartment ﬁxing screw.

e. Battery compartment.

f. Hooks.

g. Mounting bracket.

h. Mounting holes (for the hooks on the mounting bracket).

i. Mount by aligning notches and hooks, then rotate clockwise.

Installation recommendations

• It is recommended to install the device in

the center of the ceiling.

• The device should be placed openly,

unobstructed by appliances and furniture.

• It is recommended to place a smoke

detector at the top of a stairway to detect heat and smoke rising

from below.

• For the device to function correctly, it is important to ensure that

its readings are done accurately in a stable environment. In order to

achieve this:

• Do not place the detector in the kitchen: Cooking fumes may

trigger the alarm.

• Do not place the detector near a ventilation fan, ﬂuorescent lamp

or air-conditioning unit: Air drafts may aﬀect the accuracy of the

detector.

• Do not place the detector near ceiling beams, at the top point of

an “A” frame type ceiling or over a cabinet: Stagnant air in these

areas may aﬀect the accuracy of the detector.

• Do not place the detector where it may be exposed to direct

sunlight.

• Avoid installing the smoke detector in areas where other

installations may cause rapid changes in temperature within

the detection area, e.g. near air conditioners, heaters, boilers or

radiators.

• Avoid large obstacles in the detection area.

• Moving objects within the PIR detection area (e.g. curtains moving

in a draft) may cause an unwanted alarm. Avoid if possible.

The sensor will give false alarms when used in dusty areas like

washroom with tumbledryer. To test the PIR motion sensor: Press the

function button to enter test mode. Walk around the protected area,

and notice when the LED lights up. Check that the detection coverage

is adequate.

The smoke detector is designed to be mounted on the ceiling. The

ideal mounting height for the smoke detector is 2.7 to 3 meters above

ground. Mounting the detector higher than 3 meters above ground

may aﬀect detection performance.

The smoke detector can support detection coverage within a

diameter of 5 meters. Please refer to the illustrations below for

installation details.

6. ADD/REMOVE

Please read this before installation

The primary controller/gateway has a mode for adding or removing

devices. Please refer to your primary controller manual on how to set

the primary controller in add/remove mode. The device may only be

added or removed from the network if the primary controller/gateway

is in add/remove mode.

After power is applied, the smoke detector initiates a 1-minute warm-

up period. During this minute, the device will automatically enter add/

remove mode, and may now be added to the system via the primary

controller.

After the calibration process is ﬁnished, you may access the add/

remove mode by pressing the function button three times within 1.5

seconds. Removing the device will reset it to factory settings.

If the device already belongs to a network, you must remove it from

that network before adding into a new one, or the setup will fail.

When the device is removed from the network, it will revert to factory

settings.

7. LED-INDICATOR /FUNCTION BUTTON

Red LED

• Turns ON brieﬂy: Transmitting signal.

• Quick ﬂash: Alarm.

• Flashes every second: Smoke detector in sleep mode.

• Flashes every 2 seconds: Smoke detector in warm-up and calibration

process.

• Flashes every 4 seconds: Battery exhausted.

LOC K

2,7m

IR Detection Coverage

At least 60 cm from

the wall

ﬂash. The smoke detector will emit 2 short beeps, then follow the

calibration process described in step 4 of the installation procedure

to set the new preferred value.

• Every time the battery is removed and re-inserted, the smoke

detecter will also set the new threshold value following the

calibration process

• After the initial installation, the smoke detector will perform

auto-calibration after 4 hours. Afterwards, it will perform an auto-

calibration once every month.

• If the calibration fails, the smoke detector will emit continuous

beeps, and the red LED will also ﬂash continuously. In this case, you

need to remove the batteries, wait for 30 seconds then re-insert the

batteries to restart the smoke detector.

12. SERIAL CONNECTION

The smoke detector may be used with other Heatit Z-Smoke

Detectors 230VAC (maximum 6 in same serial connection). The Heatit

Z-Smoke Detector Battery may be associated with the Heatit Z-Smoke

Detector 230VAC AC, which is a listening node. To beneﬁt from this

functionality, it is necessary to assign associations to the other Heatit

Z-Smoke Detectors 230VAC AC. Heatit Z-Smoke Detector Battery may

only be associated with Heatit Z-Smoke 230VAC AC (listening nodes).

NB! Serial connection between Heatit Z-Smoke Detector Battery

and other Heatit Z-Smoke Detector Battery is not possible.

1. Add all smoke detectors to the same network.

2. Assign the smoke detectors to the correct zone/room in the primary

controller.

3. Access associations from the primary gateway (please refer to

primary controller manual).

4. Assign assocations from each device using association group 2

(Sensor Basic Set) to all other smoke detectors.

This way it is ensured that no matter where the ﬁre is detected, the

devices will alarm with siren and emergency lights.

To stop an ongoing alarm, you can press the function button on

a smoke detector. If the smoke detector was triggered by another

device, the device will stop all alarms except from where the alarm

was triggered.

13. SECURITY

The S2 security enhances Z-Wave Plus with an additional layer of AES

128-bit encryption of the wireless Z-Wave communication to prevent

hacking and man-in-middle attacks on the home network.

Orange LED

• Flashes every second: Device power-on/calibration failed.

• Flashes every 5 seconds: Detecting smoke failed or device malfunctioning.

• Flashes every 4 seconds: Battery exhausted.

• Flashes every 45 seconds: Low battery condition

Function button

• Press the button once to send a test signal and temperature report to

gateway.

• Press the button once during an alarm to silence the alarm.

• Press the button 3 times within 1.5 seconds to learn mode.

• Press and hold the button for 10 seconds to enter the calibration process.

• Press and hold the button for 20 seconds to perform a factory reset.

White LED (emergency light)

• The emergency light will begin to ﬂash slowly to alert users that an

alarm has been triggered.

8. FACTORY RESET

Press and hold the function button for 20 seconds. This will reset the

smoke detector. It will also perform the calibration process.

NB! Please use this procedure only when the primary controller/

gateway is missing or otherwise inoperable.

9. TESTING THE SMOKE DETECTOR

By pressing the function button on the smoke detector, you can test if

the smoke detector is functioning normally.

• If the smoke detector functions normally, the Red LED turns on for 2

seconds, followed by a 2-tone beep.

• If the buzzer sounds 2-tone beeps 3 times, the “Optical Chamber” on

the smoke detector is either dirty or out-of-order.

• If the buzzer sounds 2-tone beeps 5 times, the “Heat Sensor” is out of

order.

10. ALARM SILENCE

When the smoke detector sounds the alarm, pressing the function

button sets the smoke detector to alarm silence mode to silence the

alarm for 9 minutes. The buzzer will only stop sounding after the alarm

has been activated for at least 1 minute.

If the smoke concentration has dropped below the alarm threshold

after the 9-minute alarm silence period has expired, the smoke

detector will emit a 2-tone beep and return to normal operation mode

without sounding the alarm.

If smoke concentration still exceeds the alarm threshold, the smoke

detector will start alarming again.

If smoke concentration continues to rise during the alarm silence

period and exceeds the second alarm threshold, the smoke detector

will start sounding again. An alarm activated by exceeding the second

alarm threshold could not be silenced by pressing the function button.

11. CALIBRATION

As the operating conditions of the smoke detector may vary after

having been installed for some time, you may wish to recalibrate the

smoke detector to set a new smoke detection threshold value and

ensure optimal performance of the smoke detector.

To do this:

• Hold the function button for 10 seconds until the red LED starts to

BATTERY AC

ACAC

Heatit Z-Smoke Detector combination

Heatit Z-Smoke Detector Battery and Heatit Z-Smoke 230VAC.

Use Asscociation group 2.

Produktspezifikationen

Marke:	Heatit
Kategorie:	Rauchmelder
Modell:	Z-Smoke

Brauchst du Hilfe?

Wenn Sie Hilfe mit Heatit Z-Smoke benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Rauchmelder Heatit

Heatit Z-Smoke Bedienungsanleitung

5 September 2024

Bedienungsanleitung Rauchmelder

Neueste Bedienungsanleitung für -Kategorien-

FirstAlert SA700 Bedienungsanleitung

16 Oktober 2024

Alecto SA-100 Bedienungsanleitung

16 Oktober 2024

First Alert HD6135FB Bedienungsanleitung

14 Oktober 2024

Clas Ohlson 32-3383 Bedienungsanleitung

14 Oktober 2024

First Alert SA710CE Bedienungsanleitung

11 Oktober 2024

Siemens DELTA reflex SD230N Bedienungsanleitung

9 Oktober 2024

Elro FS151021M Bedienungsanleitung

9 Oktober 2024

TFA AirCo2ntrol Life Bedienungsanleitung

8 Oktober 2024

FireAngel HT-630-EU Bedienungsanleitung

7 Oktober 2024

Elro 2001-023 Bedienungsanleitung

4 Oktober 2024