Hakko FX-888D Bedienungsanleitung

Hakko Lötmaschine FX-888D

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Hakko FX-888D (15 Seiten) in der Kategorie Lötmaschine. Dieser Bedienungsanleitung war fĂŒr 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/15
Cleaning wireHAKKO FX-888D Station
HAKKO FX-8801 Soldering iron
Iron holder (with cleaning sponge)
Instruction Manual
1
1
1
1
1
Instruction Manual
1. PACKING LIST AND PART NAMES
Please check to make sure that all items listed
below are included in the package.
*HAKKO FX-8802 / FX-8803 / FX-8804 (not included) can be connected to HAKKO FX-888D station.
*When using the HAKKO FX-8802/FX-8803/FX-8804, please use it with the applicable iron holder.
HAKKO FX-8801
Cord assembly
Iron holder
Cleaning sponge
Iron holder
base
HAKKO FX-888D Station
Power switch
OFFON
Cleaning wire
Receptacle
Thank you for purchasing the HAKKO FX-888D soldering station.
Please read this manual before operating the HAKKO FX-888D.
Keep this manual readily accessible for reference.
Iron receptacle
This product includes such features as electrically conductive plastic parts and grounding of the unit
as measures to protect the device to be soldered from the effects of static electricity. Be sure to observe
the following instructions:
1. The plastic parts are not insulators, they are conductors. When making repairs or replacing
parts, take su ficient care not to expose live electrical parts or damage insulation materials.f
2. Be sure to ground the unit during use.
Electrostatic Protection
AC26V 65W
< 2 ℩
< 2 mV
Ceramic heater
3.9 ft. (1.2m)
8.5 in. (217mm) with 1.6D tip
0.10 lb. (46g / 1.62 oz.) with 1.6D tip
Power consumption 70W
Station
* The temperature was measured using the FG-100 thermometer. * This product is protected against electrostatic discharge.
* Specifications and design are subject to charge without notice.
HAKKO FX-8801 Soldering iron
Power consumption
Tip to ground resistance
Tip to ground potential
Heating element
Cord
Total length (w/o cord)
Weight (w/o cord)
2. SPECIFICATIONS
Output
Temperature range
Temperature stability
Dimensions (W × H × D)
Weight (w/o cord)
AC26V
120 - 899 (50 - 480 )℉ ℃
±1.8 1℉ (± ℃) at idle temperature
{When set to 400-899℉ (200-480℃)}
3.9(W) × 4.7(H) × 4.7(D) in.
(100 × 120 × 120 mm)
2.6 lb. (1.2kg)
A. Setup the iron holder
1. Fit the small sponge pieces into the hollows of the iron holder base.
2. Add an appropriate amount of water into the iron
holder base. The small sponge will absorb water
and help keep the large sponge damp at all times.
3. Dampen the large sponge and place it on the
iron holder base.
*When using a Cleaning Wire
Place it in the iron holder as shown on the right. See
"2.Using a Cleaning Wire" in section "7. MAINTENANCE"
4.INITIAL SETUP
Small sponge
pieces
Large sponge
Warnings, cautions and notes are placed at critical points in this manual to direct the operator’s
attention to significant items. They are defined as follows:
WARNING
When power is ON, tip temperatures will be between 120 to 899℉. (50 and 480℃) To avoid injury or
damage to personnel and items in the work area, observe the following:
Do not touch the tip or the metal parts near the tip.
Do not allow the tip to come close to, or touch, flammable materials.
Inform others in the area that the unit is hot and should not be touched.
Turn the power off when not in use, or left unattended.
Turn the power off when changing parts or storing the HAKKO FX-888D.
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in safe way and understand the hazards
involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without
supervision.
The unit is for a counter or workbench use only.
If the power cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified person in order to avoid personal injury
or damage to the unit.
The unit is for a counter or workbench use only.
Failure to comply with a CAUTION may result in injury to the operator, or damage to the
items involved.
Failure to comply with a WARNING may result in serious injury or death.WARNING:
CAUTION :
CAUTION
3. WARNINGS, CAUTIONS AND NOTES
To prevent accidents or damage to the HAKKO FX-888D, be sure to observe the following:
Do not use the HAKKO FX-888D for applications other than soldering.
Do not strike the iron against hard objects to remove excess solder. This will damage the iron.
Do not modify the HAKKO FX-888D.
Use only genuine Hakko replacement parts.
Do not allow the HAKKO FX-888D to become wet, or use it with wet hands.
Remove power and iron cords by holding the plug. not the wires.
Be sure the work area is well ventilated. Soldering produces smoke.
While using the HAKKO FX-888D, don’t do anything which may cause bodily harm or physical damage.
CAUTION
Be sure the sponge is moistened with water
before use to avoid damaging the tip.
Operation and indication
Switch and control button
The front panel for the FX-888D has the following two
control buttons.
Use this button to select and change settings.−
In the temperature preset mode,
pressing this button will change the selected
preset temperature while the unit is in operation.
Pressing and holding the button will start
the adjustment mode.
−Use this button to make and confirm selections.
Pressing this button will display the current set
temperature.
Pressing and holding the button will start
the temperature setting mode.
ENTER
UP
5.OPERATION
UP
ENTER
FX 8 D-88
A. Turn on the power switch
After turning on the power switch, will be displayed
for two seconds, and current temperature will be displayed.
When the display stabilizes, the LED heater lamp will begin to flash.
B. After use
Always clean the tip and coat it with fresh solder after use.
Place the iron in the iron holder when not in use.
Turn the power off when the FX-888D is not in use for an extended period.
CAUTION
Heater lamp
4.INITIAL SETUP
Push on the plug until
it stops, making sure it is
securely connected.
Receptacle
To disconnect, hold the plug
and pull it out of the receptacle.
B. Connect the iron to the station
1. Connect the cord assembly to the receptacle.
2. Place the iron into the iron holder.
3. Plug the power cord into an appropriate power supply.
CAUTION
Be sure to turn off the power before connecting or
disconnecting the cord assembly for the iron to and
from the receptacle to avoid damaging the circuit board.
CAUTION
Do not use any iron other than those listed in Section 1 of this
manual. Doing so may result in inadequate performance and / or
possible damage to the unit.
CAUTION
The unit is protected against electrostatic discharge
and must be grounded for full efficiency.

Produktspezifikationen

Marke: Hakko
Kategorie: Lötmaschine
Modell: FX-888D

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hakko FX-888D benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Lötmaschine Hakko

Hakko

Hakko FX-888D Bedienungsanleitung

31 August 2024

Bedienungsanleitung Lötmaschine

Neueste Bedienungsanleitung fĂŒr -Kategorien-

Stamos

Stamos S-LS-4 Bedienungsanleitung

16 Oktober 2024
Stamos

Stamos S-LS-1 Bedienungsanleitung

16 Oktober 2024
Stamos

Stamos S-LS-16 BASIC Bedienungsanleitung

15 Oktober 2024
Stamos

Stamos S-LS-17 Bedienungsanleitung

15 Oktober 2024
Stamos

Stamos S-LS-12 Bedienungsanleitung

15 Oktober 2024
Stamos

Stamos S-LS-73 Bedienungsanleitung

15 Oktober 2024
Stamos

Stamos S-LS-6 Bedienungsanleitung

15 Oktober 2024
Stamos

Stamos S-LS-72 Bedienungsanleitung

15 Oktober 2024
Stamos

Stamos S-LS-10 Bedienungsanleitung

15 Oktober 2024
Stamos

Stamos S-LS-68 Bedienungsanleitung

15 Oktober 2024