Haier ES25V-E1 Bedienungsanleitung

Haier Kessel & Heizkessel ES25V-E1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Haier ES25V-E1 (2 Seiten) in der Kategorie Kessel & Heizkessel. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

1 2

ES10V-E1(H)

ES15V-E1(H)

ES25V-E1(H)

Haier Home Water eateH r

Instruction manual

0040503116

Please read this Instruction Manual carefully before use.

Please retain this manual for future reference.

Troubleshooting

Specications

Introduction of exterior and a essoriescc

Technical parameters

Electrical Diagram

Model a b c d e

ES10V-E1 (H) 300mm 338mm 456mm 152mm 100mm

ES15V-E1 (H) 335mm 374mm 495mm 152mm 100mm

ES25V-E1 (H) 370mm 409mm 546mm 152mm 100mm

Note: 1. The margin of error for the above parameters (measurements, weight) is ±10%.

2. Water tempe ture indicator is not a precision thermometer. It consists of three areas ra

denoted by blue; orange and red, which indicate the temperature of water in the

inner chamber from low to high respectively.

(Fig.2)

Remarks:

The permitted error limit of net weight above is

10%.

Item Unit ES10V-E1 (H) ES15V-E1 (H) ES25V-E1 (H)

Rated voltage V 230 230 230

Rated frequency Hz 50 50 50

Rated pressure MPa 0.80 0.80 0.80

Power W 2000 2000 2000

Net weight kg

Rated tempe turera oC 75 75 75

Volume L 10 15 25

Waterproof ade / IPX4 IPX4 IPX4gr

Mixing factor %

Tap water pressure MPa s n Pa s n Pa s n PaNo les tha 0.05M No les tha 0.05M No les tha 0.05M

Average temperature of hot ter outletwa oC

Re-heating time

(a temperature rise of 50oC) min

Diameter of power wire mm23×1.5 3×1.5 3×1.5

L : Brown wire

N : Blue wire

MT : High temperature limiter

BT : Thermostat

HL : Heating indicator

EH : Heating element

E : Yellow/green wire

Symptom Things to Check Solutions

No water

Whether the ter supply wa

has stopped or whether the

water pressure is too low

Check

2Whether the water-

usage point is blocked or

whether the hot water

valve is opened

Check and clear

Only cold

water but

the heating

indicator light

is lit

1Whether hot water outlet

is opened Check and open

2Whether the water

temperature is adjusted

Increase the temperature to the required

value. Once the water is heated to the pre-set

tempe ture, control ow volume of cold and ra

hot ter using the moderating mixing valve.wa

3Heating time is too short

and set tempe ture is ra

not achieved

Continue heating

4Whether heating pipe is

damaged

Conr thi nm s is ot d e o he u t t reaso ns123 ,

then contact Maintenance Department

On y oll c d water

and e heth ating

indicator light

is not lit

1Whether power is

properly connected Check power socket

2Whether thermostat is

out of control

Conrm this is not due to the reasons

then contact Maintenance Department

Heating

indicator light

on all the time

1Water has not reached

the set temperature Continue heating

2Whether thermostat is

out of control

Conrm this is not due to the reasons 1,

then contact Maintenance Department

Water volume is

sometimes large

o sm lr al , or water

is s meo times hot

or cold

Whether water pressure is

stable

Set lower mixing valve or ensure water

pressure is stable before use

Sma ll hot water

outlet volume

1Whether the present

temperature setting is

too low

Calibrate using the method stipulated in the

Instruction Manual

2Whether ter pressure is wa

excessive Set lower mixing valve

Safety Notices (Please read before use)

Prohibited Compulsory

Matters Essential Matters

our Service Cent nc ter o e he wat ater he er does

not work r p ope y emrl or its urn b t smell.

230 /50 z i depenV H n dent ower rce p sou

mu usst be ed at es.all tim

To r fety ensu e sa , t e h water heater shou ld

be nneco cted to indepe den nt s s ocket (do

no s pte reliabl ar gt u e ada rs) with, e e thin . In

a t ower et mu conform dd ioit n he p sock st

t nao tional ndards Us o watsta . e f er heater

without re bl rt i tric prlia e ea hing s s tly ohibited.

Us n imet te pe mult er o hecc k w ether he lih t ve

line and neutr ial l ne e ar reve e.rs

Do not dam d wiruse age e pand ower

socket. Pr p om tly cl an th dust one e the

power p g lu and soc t.ke

Check he pt ower met n her a d t e electric

wir die's ameter to ur ens e that t ey h co y mpl

with h rated urrent f t e c or th e water

electr ia tic n o eck t e ech h lectri ircuit.c c

nea the r wat ater i trictlyer he s s prohibited.

Do not touch t uhe pl g with wet s, hand

an sud e mak re that t e h water heater, plug

so docket not c into con ct ome ta with

water. f I they are accid tallyen wet, heyt

mu chst be ecked by professional rsons pe

a nted by our c pan forppoi om y be e using,

in order t revento p electrocution.

Do not connect to ower en p wh installing

or ai rep ring t e h water heater.

Non-professionals are strictly prohibited

from carrying out repairs, maintenance,

dismantling or revamping of the ter wa

heater.

Installati ter at utd s on of wa he er o oo irs

strictl roh ted.y p ibi

Do no installt t e h water heat i nvironment er n ean

w ch chi is sus ep e tibl to ice-formati Ic wi on. e ll

ca h conta er and water touse t e in pipe break,

le inad g to scal and water l kage.ding ea

Pl sea e t ke p eca r autionar m ures y eas

durin col weat rg d he , o dein r r to prevent

damage er to twa heat ro rer f m f ee inz g.

I h oft ower l df t e s p cab e d ageis am , it

from t e ufah man cturer M ntenance s or ai

D rt n rder t avoepa me t oin o id anged r.

Take ca e not be sr to calded y b heat ter. ed wa

· Touching of ot er h wat valve an pipes d is

strictl roh ted.y p ibi

Ma sur to e hke e ch ck t e er wat temperature

befor use s onle , u e y w en ih t f comfor e.eels tabl

D o t ro h tero n t use wa er f m t e wa heater

for drinking or similar r s. pu pose

wat at w n uer he er as ot sed r n fo a ext d ende

pe d of trio ime rai h t heater of . D n t e wa er

al tl wa er a ordi to tcc ng he instruction n s i

th hae c pter l M nte ce.on C ea g nin and ai nan

A: Water inlet pipe

B: Water outlet pipe

C: Inner chamber

D: Heater

E: Magnesium rod

F: Temperature

measurement pipe

G: Wall-mount support

H: Washer

Meanings of Icons

Earthing

For nbidde

For enbidd

For denbid

For enbidd

For denbid

For enbidd

Warning

War inn g

Warning

Ca onuti

Caution

For enbidd

ＣＳＨ１０Ｄ００３８＿ＥＮ．ｉｎｄｄ　　　１５／２５／２０１０　　　４：２７：１５　ＰＭ

2.7 0.9 3.0

6964

811 14

20 25 45

e is ≥0.80M

5 6

3 4

Mu n l b n r c anst be i sta led y perso nel in ou omp y's -sa epa me t or esi ed nstAfter les D rt n d gnat i all tion pe sona r nel.

The water heater is wall-mounted type.

Determine the installation position of the ter heater. Based wa

on the measurements indicated in Fig. 2, use impact drill to

drill two holes of 12mm in diameter and 65mm in depth.

Insert the expandable hooks into the holes and ensure that

they are securely xed. Lift the water heater and slip its wall-

mount support onto the expandable hooks (as show in Fig.1).

Check to make sure the machine is securely suspended.

For a essories such as safety valve, please refer to the cc

“Installation of Safety Valve” (for reference only). Make sure to

seal the joints with Teon tapes to prevent water leakage.

For ease of installation and removal of water heater, we

would recommend that G1/2 loose joints be installed at

appropriate locations on the ter inlet and outlet pipes of the water heater. Determine the position of wa

the hot ter supply. Connect the ter inlet and outlet pipe together with the ter pipe to the positions wa wa wa

reserved for use of hot water. Hot ter pipe should preferably not be too long in order to prevent heat loss.wa

Note: Make sure that the ter heater is securely attached to the hook before letting it go; otherwise it wa

may drop and cause injury or property damage.

When installing the ter heater, certain space should be reserved (not less than 250mm from the top wa

and bottom and not less than 700 mm from the front and the sides), for ease of subsequent maintenance

and repair. If the water heater was to be built into clip boards, the bottom section of the clip board should

be movable for ease of removal of plastic cover during maintenance.

Make sure the pressure on the water inlet is not less than 0.05MPa, and not more than 0.75MPa.

The water heater should be installed indoors in a place where the ambient temperature is above 0

C. The

pipes uld be c e d t. The hot ter et d not be too f away from the point of age. If e sho los ly lai ou wa outl shoul ar us th

distance exceeds 8 meters, the hot water pipe should have insulation protection, in order to prevent heat loss.

The wall on which the ter heater should be strong such as it is able to withstand fourth the weight of the wa

water heater when lled with water. If the wall was not weight-bearing wall or made of hollow bricks, adequate

protective measures such as addition of support and high-strength wall screw with back panel should be adopted.

The water heater should be installed in places such as it is easy to use and maintain and with oor drain,

in order that it will not cause damage to nearby facilities or those in the lower levels during a leakage

of the water tank or water pipe. It should not be installed over toilet bowls, bathtub, wash basin or door

frame in order that users do not feel oppressed or insecure.

Power socket for the water heater should be installed in dry places which do not easily come into contact with

Do not reverse the installation for the ter inlet and outlet. The safety valve should be installed in the wa

designated position and should not be moved without permission. The safety valve's pressure-relief hole

should be connected to the atmosphere and free from blockage at all times.

Use pen multimeter to check whether the live line and neutral line are reverse. Turn on power supply only

when you have ensured that the heater is lled with ter and that there is no water leakage. The power wa

supply should also conform with requirements.

Safety reminder: In order to prevent accidents, please use our company's accessories during installation. Do not

replace them on your own or use substitutes. Please make sure to contact our Maintenance Department if the pipes

or a essories are damaged and replace them with the accessories supplied by our company. Our company shall not cc

be liable for any direct or indirect losses caused as a result of accidents for failure to comply with the aforesaid.

All ter pipes should be installed by qualied water pipe installation workers. The pipelines should wa

comply with the national standards and regulations on the prohibition of prevention tools to draw ter wa

to water source pipelines by way of inverse siphon, as well as local building codes.

Installation method

Installation Precautions

Fig.1

Wall-mount support

Expandable

hook

Instruction manual

Operation

After completion of installation, make sure to turn on the water inlet valve and mixing valve

since there is no water in the inner chamber. Turn the mixing valve to the maximum for hot

Inspect all connections to ensure that there is not ter leakage before connecting to power.wa

Adju he wate t perast t r em tu nobre k at the otb tom

of the water heater to set the temperature.

Maximum ter temperature setting is 75wa

Temperature adjustment knob: Slowly turn the knob clockwise

to raise the temperature setting. The knob will not continue to

turn once it reaches maximum temperature setting. Turn it anti-

clockwise gradually to reduce the tempe ture setting. Once the ra

mi imu ttin m tempe ture sera ng is reached, the ter heater's power wa

If the heating indicator light is lit, it means that the water heater is heating.

Observe the water temperature indicator for

the current water temperature.

Wate a n b o ar he ti g will e n st nd y au omb t atically

when the water temperature reaches the set temperature. Once it lowers

to certain temperature, power will be automatically connected.

Do not connect the power before lling the inner chamber with water in order to

prevent damage to the water heater.

Adjust the ter temperature to the suitable level before use in order to prevent scalding.wa

Insofar as there is adequate hot water, set a lower tempe ture to reduce heat loss, high ra

temperature corrosion and scaling. This will extend the water heater's lifespan.

To avoid danger caused by accidental resetting of the heating breaker, the power for

the heat cannot be supplied by timer and other external switch devices or connected to

circuit with frequent switching for facility use.

Observe the water drainage of the safety valve's pressure-relief hole.

When the water pressur Pa and the pressure-relief hole on the safety valve emits

large volume of water, it means that the ter pressure is excessive. In such case, please notify wa

the After-sales Department.

Things to note during use



Wa r te

t u emperat re

knob

He ngati

indica or light t

Water temperature indicator

Cleaning

Check

Not in use for an extended period of time

Warning!

The water heater must be repaired or maintained by qualied professionals. Improper

methods may cause serious injury or damage to property.

Cleaning and Maintenance·Packing List

External cleaning

Take a wet cloth and dab it with small quantity of neutral deterge . Lightly wipe the ter heater. nt wa

Do not use petrol or other solvents. Finally use a dry cloth to wipe,

make use to dry the water

heater thoroughly. Make sure not to use detergents containing abrasive agents (e.g. toothpaste); acidic

substances; chemical solvents (e.g. alcohol) or polish to clean the water heater.

Internal cleaning

In order to ensure that the ter heater works eciently, the heating pipe and inner chamber should wa

be cleaned once every three years. Take care not to damage the exterior of the heating pipe or the

protective layer on the surface of the inner chamber. Depending on the local water quality and the

usage habit, the magnesium rod might need to be regularly changed. If maintenance is required,

please contact the local Maintenance Departme .nt

When the water heater is in use, the safety valve should be checked once every month. To check it, turn

the safety valve's small handle on the side of the ter inlet pipe (take care not to hurt your hand). If there wa

is ter owing out, the safety valve is working normally. Please contact the local After-sales Department wa

if no ter ows out. In the event of damage to the safety valve, please replace it with a safety valve of wa

similar specications.

Regularly engage service personnel to carry out safety inspection and promptly clear the water heating pipes

of the ale. Che o e c mp of e gne um rsc ck als th onsu tion th ma si od it sum on; change if con pti becomes exces ve.si

If the ter heater is not used for an extended period of time, please carry out the following steps:wa

Screw the ter drainage pipe to the safety valve's pressure-relief hole; turn on the safety valve handle.wa

Turn the hot water valve to the maximum (at the same time unscrew the sprinkler head soft pipe from the ter wa

outlet valve; take care not be scalded by hot water), drain the inner chamber of water.

When the water heater needs to be used again, our recommendation is to open hot water valve before

switching on the power in order to prevent accidents. Allow any gas that may be trapped in the pipe to be

discharged. Do not smoke or allow other exposed re to be near the opened valve. At the same time, make

sure to carefully examine all the parts of the ter heater and ensure that they are in a perfect condition. wa

Make sure to ll the inner chamber with water before use.



Packing list

Install the safety valve which has a rated pressure of 0.80MPa (its connection

is G1/2) into the ter inlet pipe with the arrow on the safety valve pointing wa

at the water heater. When the ter heater is heated by electricity, a small wa

amount of water will ow from the safety valve's pressure-relief hole due to

the expansion of water in the heater. This is normal. The pressure-relief hole

should be connected to the atmosphere and free from blockage at all times.

Installation method for safety valve's drainage pipe: Attach an end of the

water drainage pipe onto the pressure-relief hole on the safety valve. You

may cut the ter drainage pipe to make it shorter, or extend it depending on the situation. wa

Connect to the other end of the ter drainage pipe to the lower water outlet. This will prevent wa

the ter from the pressure relief hole from splashing. The ter drainage pipe connected to the safety wa wa

valve should be installed in a slanted manner and in an environment which is not prone to frost.

Note: If your ter heater is not installed in a bathroom with sewer, our recommendation would be that wa

you add safety valve water drainage pipe.

Installation instruction

Description of parts

Installing safety valve

Small handle

for safety valve

Pressure-relief hole (connected

to water drainage pipe)

Sprinkler head

Cold water inlet

Hot water

outlet

Hot water pipe

Cold water pipe

Safety valve

Direction of cold water

Direction of hot water

Wa r te

t u emperat re

knob

He ngati

indica or light t

Water temperature indicator

Product Model No.

Electric Water

Heater (unit)

Safety Valve/Water

Drainage Pipe (set)

Instruction Manual

(book)

Expandable Hook

(pcs.)

ES10V-E1 (H)

1 1 1 2

ES15V-E1 (H)

ES25V-E1 (H)

Quantity Name of

parts

(Fig. 3)

󰷅󰷅󰷅 󰷅󰷅󰷅󰷅

Produktspezifikationen

Marke:	Haier
Kategorie:	Kessel & Heizkessel
Modell:	ES25V-E1

Brauchst du Hilfe?

Wenn Sie Hilfe mit Haier ES25V-E1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Kessel & Heizkessel Haier

Haier ES 15V-SD Bedienungsanleitung

4 Oktober 2024

Haier FCD-JTLD200 Bedienungsanleitung

30 August 2024

Haier GV100REMB Bedienungsanleitung

28 August 2024

Haier ES30V-A3 Bedienungsanleitung

28 August 2024

Haier ES50H-CK1 Bedienungsanleitung

28 August 2024

Haier JSQ25-13WPT(12T) Bedienungsanleitung

21 August 2024

Haier ES60H-S5K(E) Bedienungsanleitung

19 August 2024

Haier ES50H-A3(E) Bedienungsanleitung

19 August 2024

Haier JSQ20-T(12T) Bedienungsanleitung

18 August 2024

Haier EC8001-PD3(U1) Bedienungsanleitung

16 August 2024

Bedienungsanleitung Kessel & Heizkessel

Neueste Bedienungsanleitung für -Kategorien-

Sencor SWK 7706GD Bedienungsanleitung

14 Oktober 2024

Hotpoint HE30S01SAG Bedienungsanleitung

14 Oktober 2024

Tesy ModEco Electronic 50 Bedienungsanleitung

11 Oktober 2024

Junkers KBR 280-3 A Bedienungsanleitung

10 Oktober 2024

Ariston Thermo MicroGenus HE 32 MFFI Bedienungsanleitung

7 Oktober 2024

Elco Vistron H 500 Bedienungsanleitung

5 Oktober 2024

Worcester Greenstar 12i System Bedienungsanleitung

4 Oktober 2024

Nibe MT-WH21-019-FS Bedienungsanleitung

4 Oktober 2024

GE 20P06SAG Bedienungsanleitung

4 Oktober 2024

Bulex SDC 200 V TRI Bedienungsanleitung

2 Oktober 2024