Hager WGCHKTM Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Hager WGCHKTM (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂŒr 38 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
www.hager.com
Safety instructions
Electrical equipment must only be installed and assembled by a qualied
electrician in accordance with the relevant installation standards, regulations,
directives and safety and accident prevention directives of the country.
Failure to comply with these installation instructions may result in damage to
the device, re or other hazards.
Function
The key card switch is used for central switching on of electric loads by inserting a
key card as well as for storage of the key card. The key card switch is installed in the
entrance area. When the key card is removed the connected loads will be switched
o automatically after the delay time has expired (approx. 30 seconds) and the LED
orientation light of the key card switch is switched on.
The key card switch RFID works exclusively with the RFID key card programmed
for this purpose.
16A key card switch - mechanical
16A key card switch - RFID
Hager Muse / Hager Inspire
Installation and operating
instructions
2
Correct use
- Switching of incandescent lamps, high-voltage halogen lamps,uorescent lamps,
230 V LED lamps as well as dimmable electronic transformers (marked with L, C)
with halogen lamps.
- For the ush-mounted installation in standard wall boxes
(recommended wall box depth ≄ 35 mm).
- Only suitable for use in indoor areas with no drip and no spray water.
Technical data
Rated voltage: 230 V~
Frequency: 50/60 Hz
Rated current: 16 A
Delay time: 30 s (+/- 10 s)
Power consumption (standby): < 1.5 W
Contact type: relay, 1 normally-open contact
Conductor cross-section of screw terminals: max. 3 x 1.5 mmÂČ
Distance of fixing holes: 60.3 mm
Operating temperature: -5 ... +45°C
Relative humidity (without condensation): 5 ... 95 % (at 25 °C)
Standards: BS EN 60669-2-1, IEC 60669-2-1
WARNING!
To avoid possible damage to the product or spurious insulation
readings, please DISCONNECT the product before carrying out
insulation resistance testing!
ç
Information for electricians
Installation and electrical connection
DANGER!
Touching live parts can result in an electric shock.
An electric shock can lead to death.
Disconnect the connecting cables before working on the device and
cover all live parts in the area!
ç
3
Preparing the device for installation
1
Frame
Key card module
Notches Switch
insert
Loosen the frame on the notches with a at-blade screwdriver ( ).1
Carefully remove the key card module from the switch insert.
Connecting the device
L LOAD N
L
N
E
2A
L LOAD N
L3
N
E
L2
L1
2B
Strip connection cables approx. 12 mm.
Connect key card switch for direct switching of loads according to connecting
diagram ( ). Can be installed alternatively with a load contactor ( ).2A 2B


Produktspezifikationen

Marke: Hager
Kategorie: Nicht kategorisiert
Modell: WGCHKTM

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hager WGCHKTM benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Hager

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂŒr -Kategorien-