Hager REQ108X Bedienungsanleitung

Hager Nicht kategorisiert REQ108X

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hager REQ108X (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/6
1
6LE000691A
REQ0..X, REQ1..X
Door station AUDIO 2wire
z
z
Safety instructions
Electrical equipment may only be installed and
assembled by a qualifi ed electrician in accord-
ance with the relevant installation standards,
guidelines, regulations, directives, safety and
accident prevention regulations of the country.
When installing and laying cables, always com-
ply with the applicable regulations and stand-
ards for SELV electrical circuits.
These instructions are an integral component
of the product and must be retained by the end
user.
Design and layout of the device
(5)
(4)
(1)
(2)
(3)
(6)
Figure 1: Design and layout of the device front
(1) Front plate stainless steel
(2) Microphone
(3) Door loudspeaker
(4) Twilight sensor for call button
(5) Button panel with call push-buttons
(6) Cover strip for dismantling protection
(10)
(7)
(8)
(9)
TOP
(11)
(12)
Figure 2: Design and layout of the device back
(7) Adjustment button Upwards
(8) 7-segment display
(9) Selection button
(10) Adjustment button downwards
(11) Module bus connector
(12) Connection terminal block
Function
The audio door station works in the 2wire bus sys-
tem and enables communication via sound.
Correct use
- for surface- or  ush-mounted installation
- not compatible with intercom systems of other
manufacturers
- suitable for use exterior applications
Product characteristics
- completely pre-assembled
- protected against vandalism
- with brushed 2 mm stainless steel front plate
- Name plate can be changed from the front with-
out any special tools
- One-man commissioning
- call button with acknowledge tone (can be
switched off) and tactile feedback
- call button, light release or door release can be
adjusted even without any function
- durable, homogeneous, white LED call
push-button backlighting
- Twilight controlled call push-button backlighting
with adjustable switch-on brightness level
- Opening of door station only with enclosed
opening tool
- break-proof  ush-mounted call buttons
- Loudspeaker and microphone protected against
sabotage
- Volume and microphone sensitivity settable
- Door release contact on 1 ... 10 s adjustable
- Door release without previous call adjustable in
single door systems
- Safety rope as installation aid
Operation
Establish call (ringing)
zPress the call push-button assigned to the
desired subscriber.
If con gured, the call push-button activation is
con rmed by an acknowledge tone. Addressed
indoor stations are called.
Switch-on lights
A call push-button is con gured and labelled for
lighting control (light insert supplied).
zPress the call push-button for lighting.
zIf con gured, the call push-button activation is
con rmed by an acknowledge tone. The light
contact of a line power supply is closed for the
set time.
Label call push-button
zKeep call push-button pressed on one side.
On the opposite side, the lever opening (14) is
accessible for a screwdriver.
zPosition the screwdriver in the lever opening
(13) and release the interlock (Figure 3).
zRemove cover with name plate insert.
2
(13)
Figure 3: name plate change
(13) Lever opening
zLabel name plate insert if required.
zInsert name plate insert, prepared foil or pre-
pared labelling strip into the cover and press on
cover.
Do not use any paper for the name plate insert,
since moisture and UV light will damage the
paper and labelling.
UV-resistant foil with laser printing is suitable
for labelling as well as labelling devices for
labelling strip:
- small buttons - 12 mm
- medium buttons - 30 mm
Door stations with status indication
Dis-
play
Cause Function/Lighting
duration
A subscriber is
called.
After 90 s without call
acceptance or an opera-
tion on the door station,
goes out.
A subscriber
accepts the
door call.
goes out, lights up
as long as the intercom
connection is pressed
down, max. 3 min.
The door is
unlocked.
Call not accepted:
Symbol goes out and
lights up for the un-
locking time set on the
door station.
Call accepted:
In addition to the
,
the
lights up for the un-
locking time set on the
door station. goes out
approx. 5 sec after the
symbol.
Table 1: Status indications of door station
Cleaning and care
Commercially available products for stainless
steel and car paintwork care containing a wax
component for conservation are recommended for
cleaning and care.
Do not use wire wool, wire brushes or any
similar products for cleaning. This will prevent
damage to the surface and accumulation of
ash rust.
P
P
P
Information for electricians
Installation and electrical connection
DANGER!
Touching live parts in the installation
environment can result in an electric
shock!
An electric shock can be lethal!
Before working on the device or load,
disconnect all associated circuit brea-
kers. Cover all live parts in the area!
ç
When installing door communication systems,
comply with the general safety regulations for tele-
communications systems according to VDE 0800:
- Separate routing of power and door communi-
cation cables with a minimum spacing of 10 cm
- Partitions between power and door communica-
tion cables in shared trunkings
- Use of standard telecommunications' cables, e.
g. J-Y (St) Y with 0.8 mm diameter
Bus cables
- J-Y(ST)Y or A-2Y(L)2Y
Use wrapped wire pair.
Recommendation: white/yellow
- CAT
Use wrapped wire pair.
Recommendation: orange/white
- YR
Use adjacent wires.
Mounting door station
Surface-mounted or  ush-mounted housing is
installed (see Assembly instruction housing).
The connection cables and indoor stations are
connected to the line power supply while taking
the maximum cable lengths and attenuations into
account (see operating instructions of the line power
supply).
zThe fastening elements supplied with the
ush-mounted housing must be assembled with
the nuts on the top and bottom on the threaded
bolts. The support bracket (14) of the fastening
elements must be located on the wall surface.
(14)
Figure 4: Support bracket of the fastening elements
(14) Support bracket of the fastening elements
zInsert opening tool (15) into the mounting de-
vice of the lower fastening element (16) on the
housing (Figure 5).
(15)
(16)
Figure 5: Inserted opening tool
(15) Opening tool
(16) Fixing element
zAttach the loops of the safety rope (17) to the
upper left suspension of the door station and to
the upper fastening element (18) in the housing.
Place the door station for installation onto the
opening tool (Figure 5).
(18)
(17)
Figure 6: installation position of door station
Individual call push-
button address/function
Automatic call push-
button addressing
Door speaker
volume
Microphone sensiti-
vity
Operating sig-
nal sound volume
Door release
unlocking time
Door release
function
set
door address
Camera present
Call push-button
Backlighting
settings
(switch-on bright-
ness level)
Display error
codes (max. 5 can
be saved)
Reset error codes
factory setting
Confi rm the call
push-button to be set
= Cancel
= Start addressing
...
Default setting
...
Default setting
...
= Acoustic signal off
Default setting
... Seconds
Default setting seconds
= only with door call
= also without door call 1)
Default setting
x ... x
x = received line
address
Default setting
= No camera
= with camera
Default setting: Audio
Video
...
= Off
= lowest value
= highest value
= always on
Default setting
... Error codes
= module communication
= sticking call button
= module address
= no error present
= Cancel
= Reset
= Cancel
= Reset
1) Door release functions without door call only possible
Figure 7: Overview
3
(17) Safety rope
(18) Upper  xing element
Connect door station
zShorten connection cable of the door station as
required and strip the required wires.
zPull off connection terminal block (12) from the
audio insert.
zConnect the wire pair of the 2wire bus cable
to the terminals of the connection terminal XX
block (Figure 8).
zConnect door release to the terminals of TT
the connection terminal block ( gure 8 and 9) if
required.
or:
zFor manipulation-protected installation, connect
the door release to the contact of the line
power supply (Figure 10).
The door release lead must not be inserted
through the door station in order to protect
against manipulation.
P
zFor call push-button backlighting connect 12
V~ lead from the power transformer to the
terminals of the connection terminal block ~~
(Figure 8... 10).
(12)
Figure 8: Wired connection terminal block
Information on the connection as a  oor door
station can be found in the operating instruc-
tions of the line power supply.
zAttach connection terminal block to audio insert.
P
Circuit symbols and elements of the circuit
diagrams
Line power supply RMD
Power transformer
Door release
Door station audio
Wrapped wire pair for 2wire devices (recom-
mendation: white/yellow wire pair)
Unwrapped wire pair, for e.g. for door release
Figure 9: Door release connection on the door station
Figure 10: Connection of door station with manipu
lation-protected door release
... = Call push-button address
= Light push-button
= Door release push-button
= no function
Address/Function
saved,
is displayed
Addressing executed/cancelled,
is displayed
Volume set,
is displayed
Sensitivity set.
is displayed
Volume set,
is displayed
Unlocking time set,
is displayed
Door release function is set,
is displayed
Door address set,
is displayed
Camera option set,
is displayed
Backlighting set,
is displayed
Error codes were deleted,
is deleted
Error codes were displayed,
is displayed
Reset to the factory setting, in-
dication goes out
e single door systems
of system settings

Produktspezifikationen

Marke: Hager
Kategorie: Nicht kategorisiert
Modell: REQ108X

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hager REQ108X benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Hager

Hager

Hager VM206 Bedienungsanleitung

13 Oktober 2024
Hager

Hager NCN110A Bedienungsanleitung

11 Oktober 2024
Hager

Hager BD163T Bedienungsanleitung

9 Oktober 2024
Hager

Hager NCN303A Bedienungsanleitung

9 Oktober 2024
Hager

Hager VM202K Bedienungsanleitung

9 Oktober 2024
Hager

Hager JK116BA3 Bedienungsanleitung

4 Oktober 2024
Hager

Hager JK108BSH Bedienungsanleitung

4 Oktober 2024
Hager

Hager JKD188TM Bedienungsanleitung

27 September 2024
Hager

Hager JK104BF Bedienungsanleitung

23 September 2024
Hager

Hager VM118SPD Bedienungsanleitung

19 September 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024