Hager 85745229 Bedienungsanleitung

Hager Nicht kategorisiert 85745229

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hager 85745229 (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

Operation and

installation instructions

Berker GmbH & Co. KG

Zum Gunterstal

66440 Blieskastel/Germany

Tel.: + 49 6842 945 0

Fax: + 49 6842 945 4625

E-Mail: info@berker.de

www.berker.com

05/2022

6LE008045A

KNX radio timer quicklink

Order-No. 8574 52 ..

KNX Radio timer quicklink

Safety instructions

Electrical equipment must only be installed

and assembled by a qualied electrician in ac-

cordance with the relevant installation stan-

dards, regulations, directives and safety and

accident prevention directives of the country.

Failure to comply with these installation in-

structions may result in damage to the device,

re or other hazards.

The radio transmission is not suitable for safe-

ty or alarm applications.

These instructions are an integral component

of the product, and must be retained by the

end user.

Design of the device

(3)

(5)

(6) (7)

(4)

(2) (1)

Figure 1: Design of the device

(1) Insert (see Accessories, not in scope of

delivery)

(2) Frame (not in scope of delivery)

(3) Application module

(4) Display

(5) Design cover

(6) Screw for dismantling protection (not for

design lines R.1/R.3)

(7) Operation buttons

Function

This device is a product of the quicklink system, in

which installation devices communicate via radio

signals.

quicklink stands for a conguration mode in which

the function-related connection between trans-

mitters and receivers is set on the device through

push-buttons and displays without further tools.

All devices congurable by quicklink can be opera-

ted together in one system.

This device is compliant to the R&TTE-Directive

1999/5/EG. The Declaration of Conformity and

further system information can be found on our

homepage www.berker.de.

The device may be used in all EU and EFTA

countries.

Correct use

- Application module for relay switch insert or

power supply for radio application modules

- Manual, time-controlled or automatic switching

of the connected loads

- Transmission and reception of manual, time-

controlled and automatic operation commands

via quicklink

- Only suitable for use in indoor areas, no drip or

spray water

Product characteristics

- quicklink functions for inclusion in the remote

and group control of lighting

- Integration into scenes

- Two preset standard time programmes

- Individual adjustment of the time programmes

possible

- Astro programme for automatic operation at

dawn/dusk

- Astro time shift to adjust the switching times

- Holiday programme for random switching times

in automatic mode

- Party programme to avoid unintentional swit-

ching operations through automated switching

commands as well as radio/extension com-

mands

- Keylock

- Automatic switching to standard/daylight saving

time

- Brightness-dependent switching when using a

radio sun sensor

Performance after mains breakdown/return of

mains supply

- Mains breakdown:

Saving of the current conguration and pro-

gramming in the non-volatile memory. The de-

vice then switches to economy mode. Only the

internal clock continues to run to keep the time

up-to-date. The use of a bu󰀨er memory en-

sures that the time stays up-to-date for up to 24

hours.

- Return of mains supply:

The application module executes an initialisati-

on operation1), the basic display is restored.

The saved conguration and programming is

loaded from the memory. Any operations pen-

ding when the power supply broke down will

not be executed after return of mains supply.

1) If the bu󰀨er memory is full, date and time must be

entered again.

Operation

Operating concept and display elements

A short press on the and buttons (Figure 2) on o󰀨

switches loads manually, whilst a press > 2 se-

conds can trigger various functions within the

menu operation.

The current clock status is displayed. Active

functions are displayed by using symbols (Table

1). Display illumination is activated for as soon as

a button is pressed.

0 7 3: 0 Wednesday

12 4:1

2 1 2: 0

on off

(8) (11)(9) (10)

(13)

(14) (12)

Figure 2: Display and operating elements

(8) on button

(9) Back button

(10) OK button

(11) o󰀨 button

(12) Display of weekday and time

(13) Display of the active function/programming

(14) Display of next switching times

Symbol Function

Keylock active

Manual operation,

no automatic switching times

Preset programme (week programP1 -

me) or (week/weekend program-P2

me) is active

Astro programme is active,

switching times are controlled depen-

ding on dawn/dusk times

Party programme is active,

manual operation only. Programmes,

extension units and radio commands

are not executed

Normal radio operation is active,

radio commands for master or group

controls can be transmitted and re-

ceived.

Stand-alone operation,

Device has temporarily been removed

from higher-level master controls, but

can still be active as a group control.

Holiday programme

Random variation of switching times,

only possible in combination with

Device is in radio conguration mode.

Table 1: Symbols in the function/programme line

(13) of the display

Switching - operation from the basic display

Manual operation of the controlled loads is pos-

sible at any time from the basic display, even if

automatic programmes are active.

Press the button.on

Load switches ON.

Press the button.o󰀨

Load switches OFF.

Locking/unlocking operation

The operation buttons of the time switch can be

locked, in order to prevent unintentional operation,

e.g. by children.

The time switch is in the basic display.

Press the button for more than 5 seconds.á

is displayed. The operation buttons are

locked.

Press the button again for more than 5 á

seconds.

disappears in the display. The operation

buttons are enabled.

Opening the menu and navigating

The device is set and programmed via the menu.

o p e r at i n g

m o d e

h o l i d ay

mo de

(17)

(15)

(16)

Fig. 3: Main menu

(15) Selected menu item

(16) Position display of the selected menu item in

the list of options

(17) Next option in the list

Short press on any button.

Operation is activated. The display is illumina-

ted.

Press the button for more than 2 seconds.OK

The main menu is displayed. The rst menu

item (Fig. 3, 15) is Auto/Manual operation

highlighted dark.

Press the ( ) or ( ) button to navigate on o󰀨 

through the menu.

The selected menu item is highlighted dark.

Conrm the selected option by pressing OK.

The submenu opens.

Navigation through the menus can continue as

described above.

Press the button.á

The display switches to the previous contents.

To return to the basic display, press the á

button multiple times as necessary.

If no button is pressed for a period of two mi-

nutes, the display returns to the basic display.

Figure 4 shows an overview of the functions in the

menus/submenus: for the user and for the A.. E..

electrician refer to sections for additional informa-

tion Menu items in brackets are visible depending .

on the timer programming status.



display settings

07 3:0

Wednesday

12 4:1

21 2:0

manual operation

P1: 7 - 21h

P2: 7 - 21h + 8 - 22h

(astro mode)

party mode

(activation)

(deactivation)

Deutsch

English

Francais

country-city selection

coordinates

2 s

language

time settings

astro settings

factory settings

summer/winter time

operating

mode

holiday

mode

program

settings

time / date



modify

(restore defaults) 



advanced

settings



standalone

mode

(activation)

(deactivation) 

configuration

select quicklink

function

quicklink settings 

Displayed in

selected language

(e.g.: English)

(18) (19)

(20)

(21)

(22)

(23)

(26)

(27)

(25)

Figure 4: Menu overview

Setting the values

Values, such as time or date, have to be set rst

for the programming of some functions.

The value to be set is selected and is highlighted

dark.

Press the ( ) or ( ) button.on o󰀨 

Short press on button: Change the value by

one step.

Keep button pressed: Scroll through values.

Scrolling stops when the button is released.

M o nt a g - S on n ta g

0 6 : 0 0

(28)

If switching times are set, then a symbol (28)

shows whether it is an ON or OFF switching

time.

Press the button.OK

The set value is applied.

Press the button.á

The display switches to the previous value. The

setting is not applied.

Submenu A1 - Select programme

One can choose between the following pro-

grammes:

- : Manual operation

Operation takes place solely using the buttons

(see Switching - operation from the basic dis-

play).

- Time programmes and P1: 7 - 21 h P2: 7 - 21

h + 8 - 22 h :

These programmes are factory preset but can

be changed individually.

P1 is a week programme with identical swit-

ching times for each day, is a week/week-P2

end programme with di󰀨erent switching times

for Mon. - Fri. and Sat. - Sun.

- Astro programme:

Programme for dawn/dusk-dependent control

of the loads (see submenu A7 - Setup Astro

programme).

The Astro programme is only displayed if it

has been set up.

- : Party

The Party function prevents unintentional swit-

ching of the connected loads by programmed

switching times or extension unit operation, e.g.

switching patio lighting OFF during a barbecue.

When the Party programme is active, a load

can only be operated manually using the but-

tons on the time switch. Control via high-level

control-sections and sensors as well as by ex-

tension units, radio and forced control com-

mands is deactivated.

If the load is moved to a dened state in forced

mode (see Table 4) and this forced mode is

active, then the Party programme cannot be

selected and the following message appears in

the display: Party programme not available

in forced mode

The device shows the Programme selection

submenu (Fig. 4, 18). The most recently selected

programme is highlighted dark.

ma n ua l o p er a tio n

P 1 : h 7 - 2 1

P 2 : h + h 7 - 2 1 8 - 2 2

Press ( ) or ( ) button to select the on o󰀨 

desired programme.

Press the button.OK

The screen switches to the basic display. The

selected programme is run, the corresponding

symbol (Table 1) is shown in the display (Fig.

2, 13).

Submenu A2 - Change, delete or add to

programmes

The options and (Figure modify restore defaults

4, 22) can be used for the preset factory pro-

grammes:

- to adapt, add to or delete operation modify

times. A maximum of 20 operation times per

day are possible.

- -restore defaults to reset a modied pro

gramme to the factory default programming.

Switching times can only be edited individually

under . It is not possible to edit pro-modify

gramme blocks (e.g. Mon. - Fri.).

Press the or button to select options or on o󰀨

to change the values.

Press the button.OK

Short press on button: Conrmation of the

current selection or the set value.

Long press on button (> 2 s) in programme edi-

ting: Adding an extra switching time or deletion

of an existing switching time.

a dd st ep

de l e te

Press the button.á

Short press on button: The display switches to

the last content.

Long press on button (> 2 s): Programming is

completed, the switching times are skipped.

Changes can be saved or rejected.

save

m o d i f i c a t i o n s ?

Y e s N o

Should no OFF switching time follow an ON

switching time, or vice-versa, then the user is

informed on the display before saving, that

switching times are missing. Saving is never-

theless possible.

attention

i n co m pl e te s eq u en c e

Submenu A3 - Activating/deactivating Holiday

programme

The Holiday programme is a simple form of the

presence simulation. The switching times of an

existing programme (P1, P2, Astro) are varied,

randomly, by ± 15 minutes. If switching times are

too close together (di󰀨erence < 15 minutes), then

they are not varied.

The time switch can be found in the submenu

Holiday programme (Fig. 4, 20).

Conrm activation with .OK

The screen switches to the basic display and

the symbol for is Holiday programme

displayed (Fig. 2, 13).

or:

Conrm deactivation with .OK

The screen switches to the basic display and

the symbol for is Holiday programme

hidden in the display.

Submenu A4 - Activating/deactivating Stand-

alone programme

The Stand-alone programme can be used for

radio installations, in which the time switch was

assigned to a master controller as a subordinate

controller. In Stand-alone operation the device

ignores the radio commands of higher-level master

controls and forced control commands, as well as

extension unit signals, i.e. operation commands

concerning the local load are not executed.

If the load is moved to a dened position in

forced mode (see Table 4) and this forced mo-

de is active, then the Stand-alone programme

cannot be selected. The following message

appears in the display: Stand-alone pro-

gramme not available in forced mode

The timer can be found in the submenu Stand-

alone programme (Fig. 4, 21).

Conrm activation with .OK

The screen switches to the basic display and

the symbol for Stand-alone programme

is displayed (Fig. 2, 13).

or:

Conrm deactivation with .OK

The screen switches to the basic display and

the symbol for normal radio operation

is displayed (Fig. 2, 13).

Submenu A5 - Set time/date

In the main menu (Fig. 4, 18), is high-Time/date

lighted dark.

Short press on button.OK

The hour display as an active element is high-

lighted dark.

Set the date and time (see Setting values).

When all the setting options have been run

through, the screen returns to the basic display.

Submenu A6 - Set time options

can be activated or deactivated for the timer.

The submenu is displayed (Fig. 4, Time setting

25).

Conrm the Summer/winter time option by

pressing .OK

a u t o

m a n u a l

Press the buttons or to select the re-on o󰀨

quired setting and conrm by pressing OK.

The device applies the setting and returns to

the submenu .Time setting

Submenu A7 - Setup Astro programme

The Astro function causes controlled loads to be

switched at dawn and dusk, meaning that the

switching times are adjusted automatically accor-

ding to the season. One can choose ON or OFF

switching operations for dawn and dusk. As these

switching times can be very early or very late, the

Astro function o󰀨ers enhanced options in order to

adapt them.

- Deviation from dawn time by ± 120 minutes

- Deviation from dusk time by ± 120 minutes

- Earliest ON/OFF switching time ( /Earliest ON

OFF at)

No switching times are executed before the

earliest ON/OFF switching time, as dened by

dawn. The lighting is switched o󰀨 at the set

time. Later Astro switching times are executed

normally.

Example:

Set time

Earliest OFF at

Sunrise Executed OFF

switching time

06:15 07:32 07:32

05:23 06:15

- Latest ON/OFF switching time ( /Latest ON OFF

at)

No switching times are executed after the latest

ON/OFF switching time, as dened by dusk.

The lighting is switched on at the set time. Ear-

lier Astro switching times are executed normal-

ly.

Example:

Set time

Latest ON at

Sundown Executed ON

switching time

20:00 17:45 17:45

21:12 20:00

The installation location must be set to determine

the correct Astro times.

- Country/city selection:

Simple setting option by selecting a country

and a city near the location from a comprehen-

sive list of European cities.

- The setting is made by entering the geographic

co-ordinates and time zone of the location.

If the location is outside Europe or a high level

of accuracy is required for the Astro times, then

the setting should be made using the co-ordi-

nates.

The submenu is displayed (Fig. 4, Astro setting

26).

Use the buttons or to select the setting on o󰀨

type and con rm by pressing OK.

The country/city selection and the co-ordinate

settings are displayed.

Set the location and times (see Setting values).

Run through all the setting options.

Having con rmed the Latest ON/OFF at? time,

a query is displayed.

co n f i g u ra t i o n

co m p l e t e d

Activate astro mode?

Yes N o

Press the buttons or to select the re-on o󰀨

quired option and con rm by pressing OK.

Yes: The screen switches to the basic display.

The Astro programme is run and the appro-

priate symbol (Table 1) displayed (Figure 2,

13). The Astro settings are saved and Astro is

added to the programme selection (Fig. 4, 19).

No: The screen switches to the basic display.

The Astro settings are saved and Astro is

added to the programme selection (Fig. 4, 19),

but is not run.

Submenu A8 - Set display contrast

In the submenu Basic setting (Fig. 4, 23), Display

setting is highlighted dark.

Short press on button.OK

The current contrast value as an active element

is highlighted dark.

co n t r a s t

5 1 %

Set the contrast (see Setting values).

Having made the setting, the display returns to

the Basic setting submenu.

Submenu A9 - Resetting the device to the

factory settings

In the factory setting, both the user‘s settings,

such as programmes or Astro settings, are re-

set and all the con gured radio logic functions

deleted.

In the submenu Basic setting, is Factory setting

highlighted dark.

Press the button for more than 10 seconds.OK

During initialisation, the display shows and 

then switches to Start-up mode. Language,

time and date must be reset.

Information for electricians

Installation

Selecting installation location

A minimum distance between the transmitter and

corresponding receiver of about 1 m must be

maintained.

A minimum distance to electronic devices which

emit high frequency signals such as computers,

electronic transformers or microwave devices of

approx. 0.5 m must be maintained.

Mounting on or close to metal surfaces may cause

impairment of the radio transmission.

Take material penetration into account. The range

of the system can be optimised by selecting the

best possible mounting location:

Material Degree of materi-

al penetration

Wood, plaster, plasterboard,

uncoated glass

approx. 90 %

Brick, press boards approx. 70 %

Reinforced concrete, ﬂ oor

heating

approx. 30 %

Metal, metal grids, alumini-

um laminates, coated glass

approx. 10 %

Rain, snow approx. 1 ... 40 %

Table 2: Material penetration

Assembly of the device (Figure 1)

The insert is installed (see operating instructions

for the insert).

Attach the application module (3) together with

frame (2) to a suitable insert (1) so that the

contact pins are inserted into the available jack.

As soon as voltage is supplied to the applica-

tion module, the display indicates whether the

application module and the insert are compati-

ble with each other:

Display text Meaning

(Operating

mode indicator) Compatible

Invalid Power

Module Not compatible

Invalid or de-

fective Power

Module!

Incompatible or missing

supply voltage. Check the

insert and replace as ne-

cessary.

Changed

Power Module /

Reset to

factory?

Compatible, but not con gu-

red to each other.

Direct reset of the radio

con guration to the factory

setting possible by kee-

ping (10 s) the button OK

pressed.

User settings (e.g. times,

programmes) remain set.

Table 3: Insert/application module compatibility

If available,  x dismantling protection with

screw (4).

Click design cover (5 or 6) into place on appli-

cation module (3).

Start-up

First start-up

The device initialises itself when the mains voltage

is switched on for the  rst time. Insert detection

is carried out and, if an incompatible device is

found, a message is displayed (see Table 3). Then

an hourglass and the manufacturer‘s logo are

displayed.

Appendix

Technical data

Radio frequency 868 MHz

Radio protocol KNX radio

Connection Mounting on suitable inserts

Power supply via insert

quicklink logic functions max. 20 transmitters/

receivers

Receiver category 2

Transmitter duty cycle < 1 %

Power reserve via internal storage battery 8 h

Charging time of the internal storage battery 48 h

Switching times max. 20 per day/140 in total

Relative humidity (no condensation) 0 ... 65 %

Ambient temperature -5 … +45 °C

Storage/transport temperature -20 … +60 °C

The Declaration of Conformity can be found on our

Internet site.

Accessories

Relay switch insert 8512 12 00

Power supply for KNX radio

application module 8502 01 00

Web

Websites to determine the location‘s latitude/lon-

gitude:

- http://www.active-value.de/geocoder/

- http://itouchmap.com/latlong.html

Warranty

We reserve the right to make technical and formal

changes to the product in the interest of technical

progress.

Our products are under guarantee within the

scope of the statutory provisions.

If you have a warranty claim, please contact the

point of sale or ship the device postage free with a

description of the fault to the appropriate regional

representative.

The language selection is displayed, the  rst lan-

guage is highlighted dark.

Deutsch

Engl his

Français

Set language, time and date (see Setting

values).

The device switches to the basic display and is

ready for operation.

- --: - Wednesday

12 : 0 8

- --: -

Submenu E1 - Radio con guration

quicklink

The radio con guration sets the functional con-

nection between commanding (transmitters) and

function-executing (receivers) radio components.

Thus wireless e.g. central unit, group, extension

unit and time controls can be realised.

The following can be con gured:

- The local operation of the load connected to

the insert

- Radio commands to control other receivers

- Functions that are executed when radio com-

mands are received

For con guration by means of Hager connec-

tion device TX100 or ETS, additional functions

are available (see operating instructions for

TX100 or application description for ETS).

Con guring the radio timer as a receiver

Con guration to control the load connected to the

insert via reception of a radio command. (Table 4).

As an example, the con guration of a wall-trans-

mitter and the radio timer as receiver is described

down below (Table 5).

If the message is displayed Connection error

during con guration, this indicates an impossi-

ble combination or an error. Reset the message

by pressing .OK

l i n k e r r o r

Con guring radio timer as a transmitter

The following radio command for activation of

receiver functions is supported:

ON/OFF (switch)

Device is con gured as an operator for

a compatible receiver. Both buttons are

assigned using a teach-in operation. The

device serves a master and active time

switch programmes are also carried out on

the receivers.

As an example, the con guration of the radio timer

with a radio push-button is shown here (Table 6).

Di󰀨 erent con guration displays, such as for recei-

vers with display, are to be taken from the receiver

operating instructions.

Deleting a con guration

To delete a con gured receiver or the local operati-

on, execute the con guration again.

Start conﬁ guration (see con guring the radio

timer as a receiver).

If necessary, Select transmitter button.

The step devices with Select transmitter button

only one transmission channel, e.g. radio moti-

on detector as a transmitter.

Select function on receiver.

Conﬁ rm the function on the receiver: press the

  or button, select Delete and con rm with

OK.

An hourglass displays the logic function

operation. The successful deletion of the logic

function is then displayed.



link deleting

successful

Con rm the message with OK.

The quicklink setting menu is displayed. The

logic function symbol is removed.

configuration

s e l e c t q u i c k l i n k

function

Finish conﬁ guration: Short press on the cfg

button the transmitter.

Con guration of group functions

By means of a group function, one transmitter

controls several receivers. To do so, the same

functions must be con gured on all receivers.

Start conﬁ guration (see con guring the radio

timer as a receiver).

If necessary, Select transmitter button.

The step devices with Select transmitter button

only one transmission channel, e.g. radio moti-

on detector as a transmitter.

Select function on receiver: Select the identical

function on each receiver to be integrated and

conﬁ rm the function on the receiver.

Finish conﬁ guration: Short press on the cfg

button the transmitter.

Con guration of scenes

Individual settings for lighting and the position

of shutters can be combined into scenes. Two

di󰀨 erent scenes can be created via quicklink and

called up by pressing a button on the transmitter.

A scene is created by con guring a transmitter

button (radio command) in the corresponding

receivers with the scene function (Table 4).

Start conﬁ guration (see con guring the radio

timer as a receiver).

Select transmitter button: Select the button for

the scene command.

Select function on receiver: Select the Scene

function on each receiver to be integrated and

conﬁ rm the function on the receiver.

Finish conﬁ guration: Short press on the cfg

button the transmitter.

Con gurable function E󰀨 ect on the receiverDisplay text

ON/OFF Change-over A short radio command switches the controlled load

alternately ON/OFF

Switch ON Switch-on A radio command switches the connected load ON.

Switch OFF Switch o󰀨 A radio command switches the connected load OFF.

1Scene 1 Scene 1 Creates the switching state saved in the scene (see

transmitter instructions).

The receiver is allocated to Scene 1 or 2 due to the

con guration of the function.

2Scene 2 Scene 2

Timer Time-controlled on

Switches the connected load ON for the set switch-on

time. Switch-o󰀨 takes place automatically when the

time has elapsed

Switch 1) On/o󰀨 (switch)

Device is assigned to a compatible transmitter as

a switch. The ON/OFF function is assigned using a

teach-in operation.

Forced mode ON Forced contr. ON Switches the load with higher priority to the appropri-

ate switching state. The execution of other commands

Forced mode OFF Forced contr. OFF

Delete Delete Deletion of the con guration

Precon gured local function (see operation).

Table 4: Con gurable functions

Step Result

Start conﬁ guration

Short press on button on the wall transmitter.cfg

If there is no further activation, the con guration is

automatically ended after 10 minutes.

The LED on the wall-transmitter lights up in cfg

red colour. (Table 1) is shown in the display Cfg

of the timer.

- - : - - Friday

12 3: 1

Cfg

- - : - -

All receivers within radio range also indicate the

con guration mode.

Select transmitter button

Short press on press-activation point on the wall-

transmitter which should activate the function.

The LED on the wall transmitter blinks for 1 cfg

second.

Select function on receiver

Open the menu (see Opening quicklink setting

the menu and navigating).

d i s p l a y s e t t i n g s

a s r o s et t i n g st

q i c k l i nk se t t in g s

c o n f i g u r a t i o n

s e l e c t q u i c k li n k

f u n c t i o n

Press the buttons or to on o󰀨 select the

quicklink function and con rm by pressing OK.

c o n f i g u r a t i o n

s e l e c t q u i c k l i n k

f u n c t i o n

A list of possible functions is displayed.

o n

off

s c e n e 1

If the transmitter button has already been

con gured with a function in a di󰀨 erent

receiver and/or the con gured function is part

of a group control, only this function can be

con gured. To change a function, the existing

con guration must be deleted and the new

one needs to be con gured.

Confermare la funzione sul ricevitore

Press the buttons or to select the required on o󰀨

function and con rm by pressing OK.

An hourglass displays the logic function operati-

on. The successful execution of the con guration

is then displayed.



link creation

successful

Con rm the message with OK quicklink setting. The menu is displayed. The

symbol indicates that a logic function was set

up.

c o n f i g u r a t i o n

s e l e c t q u i c k l i n k

f u n c t i o n

Finish conﬁ guration

Short press on button on the wall transmitter cfg

again.

The LEDs on the radio wall-transmitter and cfg

all receivers within radio range go out. The Cfg

display on the screen of the radio timer goes out.

The function is con gured.

Table 5: Con guring the function for the radio timer

Step Result

Start conﬁ guration

Open the menu (see Opening quicklink setting

the menu and navigating).

c o n f i g u r a t i o n

Con rm con guration with .OK The menu for activating the con guration is dis-

played. Con guration mode is inactive.

c f g O n

c f g O f f

Press the buttons or to select and on o󰀨 cfg on

con rm by pressing OK.

If there is no further activation, the con guration

is automatically ended after 10 minutes.

Con guration mode is active. The cfg LED of the

radio button lights up in red colour.

c f g O n

c f g O f f

All receivers within radio range also indicate the

con guration mode.

If con gured already, the fct LED of the radio

button indicates the con gured function.

Select function

Select the ON/OFF (switch) function on the

radio push-button using the button (see fct

operating instructions).

The LED blinks red and green. fct

Conﬁ rm function

To save the allocation of command and function,

keep the button of the shutter button pressed fct

for more than 2 seconds.

> 2 s

The LED blinks. After successful saving, the cfg fct

LED blinks red and green.

Finish conﬁ guration

Press the buttons or to selecton o󰀨 cfg o󰀨 and

con rm by pressing OK.

c f g O n

c f g Of f

The LEDs on the radio button and all receivers cfg

within radio range go out. The radio command for

the time switch has been con gured.

Table 6: Con guring radio timer as a transmitter

Produktspezifikationen

Marke:	Hager
Kategorie:	Nicht kategorisiert
Modell:	85745229
Produktfarbe:	Weiß
Internationale Schutzart (IP-Code):	IP20
Betriebstemperatur:	-5 - 45 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 65 %
Anzahl enthaltener Produkte:	1 Stück(e)