Gossen Metrawatt U1289 Bedienungsanleitung


Lesen Sie kostenlos die đŸ“– deutsche Bedienungsanleitung fĂ¼r Gossen Metrawatt U1289 (16 Seiten) in der Kategorie Messgeräte. Dieser Bedienungsanleitung war fĂ¼r 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/16
Operating Instructions
3-349-618-15
5/4.22
ENERGYMETER|MID
Electronic Active Energy Meters
U1281/U1289/U1381/U1387/U1389
© Gossen Metrawatt GmbH
Edited in Germany • Subject to change without notice / Errors excepted • A pdf
version is available on the Internet
All trademarks, registered trademarks, logos, product names and company names
are the property of their respective owners.
SĂ¼dwestpark 15
90449 NĂ¼rnberg
Germany
Phone +49 911 8602-0
Fax +49 911 8602-669
E-Mail info@gossenmetrawatt.com
www.gossenmetrawatt.com
Gossen Metrawatt GmbH
2 Gossen Metrawatt GmbH
1 Safety Precautions – Symbols
– Check the specified nominal voltage on the serial plate
before placing the instrument into service.
– Observe the maximum voltage of the pulse output.
– Make sure the connector cables are not damaged, and
that they are voltage-free while wiring the instrument.
– If it can be assumed that safe operation is no longer pos-
sible, the instrument must be immediately removed from
service (disconnect input voltage!). Safe operation can no
longer be relied upon if the instrument demonstrates visi-
ble damage.
The device may not be placed back into operation until
troubleshooting and repair have been performed, and
calibration and dielectric strength have been tested and
approved at our factory or an authorized service center.
– Voltage conducting parts may be exposed if the cover is
opened.
If balancing, maintenance or repair of a live open instru-
ment is required, work may only be carried out by trained
personnel who are familiar with the dangers involved.
Capacitors inside the instrument may be dangerously
charged, even after it has been disconnected from all
power sources.
– After the instrument has once again been closed subse-
quent to repair or maintenance work, insulation must be
tested with high-voltage in accordance with the values
specified in the technical data.
Gossen Metrawatt GmbH 3
Meaning of Symbols on the Instrument
DE MTP 11 B 001 MI-003 Prototype test certificate
Total insulation,
Safety Class II device
Warning concerning a source of danger
(Attention, observe documentation!)
This device may not be disposed of with the trash. Fur-
ther information regarding the WEEE mark can be
accessed on the Internet at www.gossenmetrawatt.com
by entering the search term ’WEEE’.
Metrology label with year (M11) and registration
number of the indicated authoring for module D.
Duration of Calibration validity country specific
Label with seal from federally
approved test authority
(for recalibration only)
Tamper-proof sealing
The manufacturer‘s lead seal for calibration protection is
located at the back of the instrument.
Tamper-proof sealing for the terminal cover can be attached
either at the left or right-hand side of the terminal cover.
!
M111948
EB
8
11


Produktspezifikationen

Marke: Gossen Metrawatt
Kategorie: Messgeräte
Modell: U1289

Brauchst du Hilfe?

Wenn Sie Hilfe mit Gossen Metrawatt U1289 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Messgeräte Gossen Metrawatt

Bedienungsanleitung Messgeräte

Neueste Bedienungsanleitung fĂ¼r -Kategorien-