Golden Age Project EQ-73 MKII Bedienungsanleitung

Golden Age Project Mischer EQ-73 MKII

Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung fĆ¼r Golden Age Project EQ-73 MKII (2 Seiten) in der Kategorie Mischer. Dieser Bedienungsanleitung war fĆ¼r 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
W W W . G O L D E N A G E P R O J E C T . C O M I
EQ-73 MKII
INTRODUCTION
Congratulations on choosing the Golden Age Project EQ-73 MKII equalizer!
The class-A circuit used in the EQ-73 MKII is similar to the eq section in the classical 1073 module, without
the high pass ļ¬lter. Additional frequencies have been added and the mid frequency band uses two inductors,
the higher value of the second one is used for the two lowest frequencies, 160 Hz and 240 Hz, to achieve an
optimal response.
The sound character is warm, punchy, sweet and musical. These classic characteristics have been heard
on countless recordings through the years and it is a versatile sound that works very well on most sound
sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it
available to nearly everyone.
The EQ-73 MKII has stepped frequency controls that offers a wide selection of frequencies from 20 Hz to 24
kHz.
The low and high frequency bands are shelving and the mid frequency band is of the bell type.
The control range is +/-15 dB for the two lower bands and +/- 18dB for the high frequency band.
There are separate bypass switches for all three bands.
The EQ-73 MKII can be used either as a standalone EQ or connected to the insert jack of one of the Golden
Age Project preamps. Combining one of our PRE-73 preampĀ“s and an EQ-73 MKII and using a UNITE rack kit
to mount them together, one will get a 19-inch 1073-style unit at a low cost and with a great sound!
FEATURES
- Vintage Style electronics. No intergrated circuits in the main signal path
- 3-band with a dual inductor based mid frequency band
- Stepped frequency selection
- A wide selection of frequencies from 20 Hz to 24 kHz
- Control range up to +/- 18 dB
- Separate bypass switches for each band
- Tantalum capacitors in the main signal path
- Can be used together with one of our preampĀ“s with an insert jack or as a standalone unit
- TRS jack for the INSERT mode in- and output connection, the nominal working level is around -18 dBu
- IC-based in- and output stage for the LINE IN mode with balanced TRS and XLR connectors
- Selectable ground lift jumper
- External power supply to avoid interaction with the audio circuits
- Great sound that suits most sound sources and genres
- A solid build quality that will last many years of normal use
W W W . G O L D E N A G E P R O J E C T . C O M II
CIRCUIT DESCRIPTION
The main signal path in the EQ-73 MKII
consists of two gain stages that uses
three transitors each and a few resis-
tors and capacitors. So, all in all, the
complete signal chain only contains six
active elements. Compare that to the big
number of transistors that are usually
used in one single integrated circuit!
The ļ¬lter circuits uses additional passive components.
The ļ¬rst gain stage handles the LF and HF bands and the second
gain stage handles the MF band.
The MF band uses two inductors and capacitors for a classic
LC-style eq circuit. The ļ¬rst inductor has a several taps to achieve
suitable Q-values (ie, the shape of the curve) for the different mid
frequencies from 350 Hz to 10 kHz. The second inductor has a
higher value and are used for the two lowest mid frequencies, 160
Hz and 240 Hz.
The EQ-73 MKI was designed to be used in combination with a unit
with low level, unbalanced connections, saving the cost for the
classic transformer based in- and output stage. The MKII retains
the insert jack connection but an IC-based IO with balanced con-
nections and the standard + 4dBu operating level has been added
as an option. This makes it possible for the EQ-73 MKII to operate
as a standalone unit.
MODERN VERSUS OLD
It is true that there are some great ICĀ“s available today that
achieves very low levels of static and dynamic distortion.The
simple circuits that the EQ-73 MKII uses, cannot match the low
distortion speciļ¬cations of modern ICĀ“s.
It is the distortion components that imparts a sound character
to the audio signal and, if the distortion components are of the
right sort, this is a good thing since it makes the recorded voice
or instrument sound ā€œbetterā€, more musical, more pleasing to
the ear. This is one reason why vintage style units are so popular
today.
This is not to suggest that modern, transparent sounding audio
circuits is a bad thing, sometimes they are prefered over colored
ones. ItĀ“s all about taste and it depends on the genre. For most
modern music styles, color and character is deļ¬nitely a good
thing.
USING THE EQ-73 MKII
Using an equalizer is not rocket science. Here are some points
though to help you getting the maximum out of the EQ-73 MKII:
- Connect the cable from the power supply to the AC 24V connec-
tor at the back of the EQ-73 MKII. Power on the unit with the front
panel POWER switch.
- Select the operating mode with the LINE IN/INSERT switch on
the back panel, pressing the switch engages LINE IN mode. Con-
nect the signal source to the LINE IN Combo jack and one of the
OUT jacks to the next unit in the signal chain.
- INSERT mode is activated with the switch in its outer position.
Connect the supplied stereo TRS cable between the back panel
TRS jack and the insert jack of one of our PRE-73 models or any
other suitable unit that the EQ-73 MKII will to be used together
with. ā€œTipā€ of the TRS is the input and ā€œRingā€ is the output.
The two OUT jacks will output the signal also in this mode and
can then be used as an alternative output with a different sound
character.
The EQ-73 MKII in INSERT mode will now be inserted in the signal
path of the PRE-73. If you are using the EQ-73 MKII together with
one of the PRE-73 DLX models, you must engage the INSERT
switch to activate the EQ-73 MKII.
- The best way to learn how to set the controls of the EQ-73 MKII is
to experiment with different settings on different sound sources.
There are a number of frequencies added to the original design,
expanding the possibilities for soundshaping.
- The LF and HF bands are of the shelving type, ie, it affects all
frequencies below (LF) and above (HF) the selected frequency. The
eq action starts gradually above (LF) or below (HF) the selected
frequency and increases up to the maximum boost or cut. The MF
has a bell curve, ie, a cut or boost centered around the resonance
frequency.
- By engaging the OUT switches, the eq action of each band can be
easily removed for quick comparions between eq and no eq. Using
the INSERT switch in the PRE-73 DLX, one can instantly bypass
the complete EQ-73 MKII from the signal path.
- There is a Ground Lift jumper inside the unit close to the input
jack. The jumper should normally be in place. If the EQ-73 MKII is
mounted in a UNITE rack kit together a PRE-73 and / or mounted
in a rack where other units are also mounted, ground loops can
give rise to problems. You can then try removing the Ground Lift
jumper which will lift the circuit board ground from the cabinet of
the EQ-73 MKII.
PLEASE NOTE:
- The maximum boost and cut varies somewhat with the selected
frequency.
- Inserting the EQ-73 MKII in a PRE-73 will result in a small gain
change.
- Clicks can arise when the controls are operated, especially on
the HF band. This is normal and a consequence of the used circuit
design.
- The inductors and the ļ¬lter circuits in the EQ-73 MKII are sensi-
tive to electromagnetic ļ¬elds. If you have a problem with hum
or noise, try moving the unit to another physical location in your
studio.
One situation where this problem is most likely to show up is if
the EQ-73 MKII is mounted above or close to a unit that contain a
power supply with a mains transformer.
WARRANTY
The EQ-73 MKII is built to last. But as in any electronic device,
components can break down.
There is a fast blow fuse located inside the unit. If the unit dies,
please check this fues. If it has blown, replace it with a new one.
You can also try with another 24V AC adaptor if you have one avail-
able.
If this doesnĀ“t help, or if the unit has another problem, it will need
repair and you should then contact the reseller where you bought
the unit.
The warranty period is decided by the Distributor for your country.
The Distributor will support Golden Age Project resellers and end
users with repairs and spare parts.
REGISTRATION
You are welcome to register your unit at our website:
www.goldenageproject.com
---------------------------
I would like to thank you for chosing the EQ-73 MKII!
I hope it will serve you well and that it will help you in
making many great sounding recordings.
Bo Medin
Vintage character
for modern ideas

Produktspezifikationen

Marke: Golden Age Project
Kategorie: Mischer
Modell: EQ-73 MKII

Brauchst du Hilfe?

Wenn Sie Hilfe mit Golden Age Project EQ-73 MKII benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Mischer Golden Age Project

Golden Age Project

Golden Age Project EQ-73 MKII Bedienungsanleitung

12 Oktober 2022

Bedienungsanleitung Mischer

Neueste Bedienungsanleitung fĆ¼r -Kategorien-

WMF

WMF Kult Black mixer Bedienungsanleitung

27 August 2024
WMF

WMF 0416240011 KULT X Bedienungsanleitung

27 August 2024
WMF

WMF 0416210001 Lono Bedienungsanleitung

27 August 2024
WMF

WMF Coup - 0416290011 Bedienungsanleitung

27 August 2024
WMF

WMF 0416230011 KULT X Bedienungsanleitung

27 August 2024
WMF

WMF 0416170011 Lineo Bedienungsanleitung

27 August 2024
Moulinex

Moulinex LM2201B1 Mixer Bedienungsanleitung

27 August 2024
Moulinex

Moulinex Optipro Mixer Bedienungsanleitung

27 August 2024
Moulinex

Moulinex HM2000 Mixer Bedienungsanleitung

27 August 2024
Turmix

Turmix CX 500 - A31125 Bedienungsanleitung

27 August 2024