Golden Age Project Comp-3A Jr Bedienungsanleitung

Golden Age Project Kompressor Comp-3A Jr

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Golden Age Project Comp-3A Jr (2 Seiten) in der Kategorie Kompressor. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
W W W . G O L D E N A G E P R O J E C T . C O M I
COMP-3A Jr
INTRODUCTION
Congratulations on choosing the Golden Age Project COMP-3A Jr Compressor / Leveler!
The COMP-3A Jr is a one channel vintage style Compressor / Leveler. The signal path uses only discrete
components like resistors, capacitors, diodes and transistors. The input and output is transformer balanced,
using two different transformers, each one optimized for its purpose. This is the way audio components were
built before integrated circuits became available.
Integrated circuits are small and cheap and widely used in most modern designs. The drawback is that audio
components built with modern technology doesn´t always provide the best perceived sound quality or the type
of character that the modern user desires.
The subjective sound quality delivered by vintage equipment is often prefered over the one delivered by
modern units, a situation that is even more obvious now when music is recorded with clean-sounding digital
audio equipment.
This is the reason why so many vintage audio components are cloned and produced again and also why the
vintage originals are often very expensive on the second hand market.
The circuit used in the COMP-3A Jr is based on classic design elements and it uses an integrated optocoupler
to control gain. This gives the COMP-3A Jr a unique compression characteristics. In addition, the vintage style
signal path adds a wonderful and musical character to the sound. The ease of use with only two main con-
trols makes it very simple to achieve the desired sound. These attributes has made vintage products with a
similar design favourites of engineers and musicians worldwide.
A classic sound and compression style is now available at a very affordable price point with the COMP-3A Jr.
FEATURES
- Vintage style electronics. No integrated circuits in the main audio signal path.
- Transformer balanced input and output. Can drive almost any load, balanced or unbalanced. The maximum ouput level is 25 dBu.
- Uses an integrated optocoupler to control gain. The fastest attack time is about 1 ms.
- Very simple to operate with only two main controls, Gain Makeup and Gain Reduction.
- Three-position TIME switch to select different combinations of Attack- and Release time.
- Selectable jumpers inside the unit to increase the timing on TIME-switch position B and C.
- LED-meter selectable to show output level or gain reduction.
- Hardwire bypass switch for easy comparisons.
- XLR and TRS input and output jacks for flexible connections.
- Link jack for connecting to another unit for stereo operation.
- All external controls located on the front panel.
- External power supply to avoid interaction with the audio circuits and transformers.
- Compact 1RU quarter rack format. Up to four units can be mounted in our 19-inch rack kit, the UNITE MKII.
- A solid build quality that will last many years of normal use.
W W W . G O L D E N A G E P R O J E C T . C O M II
---------------------------
Thank you for choosing the COMP-3A Jr!
I hope it will serve you well and help you in making
many great sounding recordings.
Bo Medin
Vintage character for modern ideas!
THE TIME SWITCH
The attack and release time can be adjusted using the three
position Time switch.
Position A has the fastest attack and release, the timing is
similar to the one in UA´s LA-3A.
Position B has a slower attack time, the timing is similar to
the one in the Golden Age Project COMP-3A.
Position C increases the attack time further.
The attack and release time of position B and/or C can be
increased by moving jumpers inside the unit. There are two
circuit board connectors close to the front panel:
1. “T-B” (right behind the TIME switch)
2. “T-C” (to the right of the IN/OUT switch and R25)
Each one of them has two metal pins that can be connected
together by a jumper that by default from factory is only
mounted on one of the pins.
If you want to increase the attack and release time for the
B and/or C position, relocate the corresponding jumper so
that it covers both pins,
THE METER
The approximate amount of gain reduction can be diplayed
by selecting GR on the meter switch and view the scale to
the right of the LED bar. The normal reading is 0 VU with no
compression applied.
The output level can be displayed by selecting VU on the
meter switch. The scale to the left of the LED bar is then
applicable. A VU reading of 0 indicates that the output level
is about 4 dBu (1,23V RMS) which is the nominal operating
level.
STEREO OPERATION
For stereo operation, the sidechain of two COMP-3A Jr units
can be linked together through the LINK jack on the back
panel, using a TS cable. The compression action can be bal-
anced using the front panel controls on both units but it will
be affected by the tolerances of the optocouplers.
WARRANTY
The COMP-3A Jr is built to last. But as in any electronic
device, components can break down.
There is a fuse located inside the unit. If the unit dies,
please check this fuse. If it has blown, replace it with a new
one. You can also try with another 24V AC adaptor if you
have one available.
If this doesn´t help, or if the unit has another problem, it will
need repair and you should then contact the reseller where
you bought the unit.
The warranty period is decided by the distributor for your
country. The distributor will support Golden Age Project
resellers and end users with repairs and spare parts.
REGISTRATION
You are welcome to register your unit at our website:
www.goldenageproject.com
CIRCUIT DESCRIPTION
The signal is fed through the bypass
relay to the input transformer and
then on to the gain reduction circuit
which consists of a R1/R2 resistor
network, ie a serial resistor (R1)
connected to a parallel resistor
to ground (R2), this resistor is the
photo resistor inside the opto-
coupler. The optocoupler consists of a LED (light emitting
diode) that emits light on a photocell, the resistance of the
photocell depends on the amount of light.
Since the resistor network lowers the signal level, it is fol-
lowed by a gain stage consisting of one 2520-style opera-
tional amplifier. This amplifier uses only discrete transis-
tors, diodes, capacitors and resistors.
The signal is then fed to the Gain Makeup potentiometer
and onwards to the output stage consisting of one more
2520-style operational amplifier and the output transformer
that delivers a balanced and fully floating signal to the
output jacks.
The sidechain circuit derives its signal from after the R1
resistor. The Gain Reduction potentiometer regulates the
level and it then passes through several integrated amplifi-
ers that conditions the signal so that it is suitable for driving
the LED in the optocoupler.
The higher the input voltage the more light is emitted on
the photocell, it´s resistance decreases as the light inten-
sity increases, thereby bringing the audio signal closer to
ground in the R1/R2 resistor attenuator network resulting
in a lower level in the main audio signal path.
The basic attack and release time is decided by the
characteristics of the optocoupler. The COMP-3A Jr has
a TIME switch though that offers the user several timing
options.
There is also a selectable sidechain high pass filter avail-
able, -3dB @ 250 Hz, 6 dB/octave.
USING THE COMP-3A JR
The best way to explore the possibilities of any compres-
sor and how different settings affects the sound of different
sound sources is to experiment. You can also find a lot of
information on the www helping you to understand how
compressors work and how to use them.
To get started with using the COMP-3A Jr:
- Connect the cable from the power adaptor to the 24V
AC jack at the back of the unit. Power on the unit with the
switch on the front panel.
- Connect your audio source to the input jack on the back
panel and one of the output jacks to the next unit in the
signal chain. Please note that the TRS and XLR jacks are
connected in parallel.
- The GAIN MAKEUP control sets the output level. A setting
of about 2,5 on the scale will result in a gain of 0 dB with no
compression. There is approximately 24 dB of extra gain
available from the 0 dB gain setting.
- Turn GAIN REDUCTION clockwise until you get the desired
amount of compression, then compensate the lower output
level by increasing GAIN MAKEUP. The maximum compres-
sion is about 20 dB with an input level of +4 dBu.
- Engaging the high pass filter will make the compression
action less sensitive to frequencies below 250Hz.
- You can easily check the effect of the processing in the
COMP-3A Jr by using the IN/OUT switch, the unit is com-
pletely removed from the signal path in the OUT position.

Produktspezifikationen

Marke: Golden Age Project
Kategorie: Kompressor
Modell: Comp-3A Jr

Brauchst du Hilfe?

Wenn Sie Hilfe mit Golden Age Project Comp-3A Jr benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Kompressor Golden Age Project

Golden Age Project

Golden Age Project Comp-3A Jr Bedienungsanleitung

2 August 2024

Bedienungsanleitung Kompressor

Neueste Bedienungsanleitung für -Kategorien-

MSW

MSW -SPS-24 Bedienungsanleitung

15 Oktober 2024
MSW

MSW -UVRSRI Bedienungsanleitung

15 Oktober 2024
FERM

FERM CRM1027 FCO-1524 Bedienungsanleitung

14 Oktober 2024
FERM

FERM SGM1011 Bedienungsanleitung

9 Oktober 2024
Ozito

Ozito ACP-2115K Bedienungsanleitung

9 Oktober 2024
Sun Joe

Sun Joe 24V-AJC-LTW-RM Bedienungsanleitung

28 September 2024
Auto Joe

Auto Joe 24V-AJC-LTE-RM Bedienungsanleitung

17 September 2024
Draper

Draper 110V 6L Bedienungsanleitung

17 September 2024
Powerplus

Powerplus POWX1731 Bedienungsanleitung

14 September 2024
Güde

Güde 190/08/24 Bedienungsanleitung

14 September 2024