GFP 255 C Bedienungsanleitung
GFP
Laminiersystem
255 C
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für GFP 255 C (31 Seiten) in der Kategorie Laminiersystem. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/31
Gfp
255 C
July
2012
1
OPERATING MANUAL Gfp 255 C
Please read this manual carefully before operating!
Unpacking, assembly, and operating videos are available at
www.gfpsmoothstart.com
Gfp
255 C
July
2012
2
Table of Contents
Contents Page
1. Introduction …………………………………………………… 3
2. Important Safety Instructions………………………………….. 3
3. Installation Safeguards ……………………………………….. 4
4. General Safeguards……………………………………………. 5
5. Operating Conditions …………………………………………. 6
6. System Components ………………………………………….. 7
7. Control Panel …………………………………………………. 8
8. Packing List ………………………………………………… .. 9
9. Installation
A. Uncrate the machine……………………………………. 10
B. Remove machine from Skid……………………………. 11
C. Assemble machine stand……………………………….. 12
D. Set Machine on stand…………………………………... 13
E. Bolt Machine to stand………………………………….. 14
F. Attach supply support brackets………………………… 14
10. Installing upper rewind housings..…………………………….. 15
11. Additional installation items ……….…………………………. 15
12. Installing upper shaft and brakes…………. ………………….. 16
13. Loading bottom supply roll………..…………………………. 17
14. Loading top supply roll……………………………………….. 18
15. Threading film.………………………………………………... 19
16. Operation..………….. ………………………………………… 20
17. Roller gap……………………………………………………… 20
18. Laminating
A. Single sheets using a sled……………………………….. 21
B. Multiple sheets using a roll of Kraft Paper……………… 22
C. Media from a roll………………………………………… 22
19. Mounting
A. Pre-coating mounting boards…………………………… 23
B. Mounting print to pre-coated mounting board..………… 23
20. Troubleshooting ………………………………………………. 24
21. Specifications …………………………………………………. 25
22. Warranty ………………………………………………………. 26
Gfp
255 C
July
2012
3
1. Introduction
Thank you for choosing a Gfp laminator. It has been designed and manufactured to
provide years of continuous service. Please read this manual thoroughly before
operating. Please inspect the box and the laminator for shipping damage. Damage
should be brought to the attention of the delivering carrier immediately. For a list of
shipping components see “Packing List” on page 9.
2. Important Safety Instructions
In this operating manual you will find important safety messages regarding the
product.
Read these instructions carefully, failure to comply with the following safety
procedures could result in serious injury.
WAR$I$G Do not attempt to service or repair the laminator. Only
authorized maintenance and service technicians should make repairs.
WAR$I$G Do not connect the laminator to an electrical supply or attempt
to operate the laminator until you have completely read these instructions.
Maintain these instructions in a convenient location for future reference.
WAR$I$G To guard against injury, the following safety precautions must
be observed in the installation and use of the laminator
Produktspezifikationen
| Marke: | GFP |
| Kategorie: | Laminiersystem |
| Modell: | 255 C |
Brauchst du Hilfe?
Wenn Sie Hilfe mit GFP 255 C benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Laminiersystem GFP
24 August 2024
Bedienungsanleitung Laminiersystem
- Laminiersystem Exibel
- Laminiersystem Hama
- Laminiersystem Nedis
- Laminiersystem MarQuant
- Laminiersystem Olympia
- Laminiersystem United Office
- Laminiersystem Sencor
- Laminiersystem Brother
- Laminiersystem Leitz
- Laminiersystem Rexel
- Laminiersystem Q-CONNECT
- Laminiersystem Fellowes
- Laminiersystem GBC
- Laminiersystem Ednet
- Laminiersystem Desq
- Laminiersystem Genie
- Laminiersystem Pavo
- Laminiersystem Peach
- Laminiersystem Royal Sovereign
- Laminiersystem Aurora
- Laminiersystem Tracer
Neueste Bedienungsanleitung für -Kategorien-
30 September 2024
29 September 2024
27 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
4 September 2024