Geba Tronic DC 3 ECO Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Geba Tronic DC 3 ECO (18 Seiten) in der Kategorie Garagentoröffner. Dieser Bedienungsanleitung war für 24 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/18
Instructions for Assembly and Use
Industrial Door Control DC 3
ECO - Standard - de Luxe
industrial controls
®
industrial controls
®
Dealer:
X 0364.1 05/03
GB
DIP-Switch on the Comfort module
With the DIP-Switches several operating modes can be programmed.
The programming is done by switching the corresponding switch in „ON“ position.
When reaching the desired position, which is signaled by the blinking of the red
LED, the jumper must be turned back in „OFF“ position. The signaling of the desi-
red position will be repeated 4 x. The position shown at last is now programmed.
123 4 56
ON
OFF
7
Switch 1: Display of door position 1x flashing
Traffic light control red/green 2x flashing
Switch 2: Function/ kind of Diode/resistor with free cruise 1x flashing
safety edge Diode/resistor with reverse 2x flashing
Attention ! Opto - elektronic with free cruise 3x flashing
Jumper position on mainboard! Opto - elektronic with reverse 4x flashing
DW-Test with free cruise 5x flashing
DW-Test with reverse 6x flashing
Switch 3: permanent light impuls 3 seconds 1x flashing
255 seconds 2x flashing
Switch 4: Prewarning for door moves immediately 1x flashing
France
Attention ! door moves delayed 2x flashing
Jumperposition on mainboard! (France)
Switch 5: Automatic closing function Photo beam starts closing time 1x flashing
only Standard & de Luxe Photo beam sets time to 5 sec. 2x flashing
Switch 6: automatic closing time 15 seconds 1x flashing
only Standard & de Luxe 30 seconds 2x flashing
1 minute 3x flashing
2,50 minutes 4x flashing
4,25 minutes 5x flashing
Switch 7: Test photo beam Test outside 1x flashing
only Comfort Test inside/outside 2x flashing
module S 2 Test off 3x flashing
The bold type values are pre-set during manufacturing
In p1-he setting for France the door movement is prewarned by a permanent light impuls for
3 seconds, the traffic light RED flashes 3 seconds. The traffic light control activates during the
door movement to a permanenr RED signal.
only S2
Dear customer,
The DC 3 which you have purchased is one of our highest quality technical pro-
ducts. We have taken the greatest care in its manufacture to ensure that this
microprocessor controlled encoder reaches you in faultless condition. However in
the unusual event of suspected equipment failure please return the appliance
together with the enclosed warranty document to your dealer or direct to our
factory.
The extent of warranty exclusively refers to the free repair of malfunctions of the
appliance, which demonstrably are caused by faults in production or defective
material, inclusive of spare parts required for this purpose.
Therefore please first read the instructions of use carefully before you start
programming !!!
industrial controls
®
industrial controls
®
geba GmbH is released of its obligations regarding guarantee and product liability if - without prior
permission - the unit has been modified, or if the installation is improper or not in accordance with
our instruction manual.
The installer has to take care that the EMC-regulations are respected.
2 35
Processor board
TR 1
S1
L1 L2 L3 N PE U V W N PE 1 2 3 4 5 6 7 8 9
F1
F
D
R1
D4
27 25 23 21 19 17 15 13 11
+
26 24 22 20 18 16 14 12 10
-
56-57: push button UP-STOP-DOWN-STOP (N.O.)
54-55: push button autom. closing function (N.O.)
53: +24 Volt photo-beam
52: photo-beam
51: photo-beam
50: +15 Volt safety edge
49: Signal safety edge
48: ground safety edge
46-47: pre-limit switch (N.C.)
44-45: external push button STOP (N.C.)
38-39: push button inside Down (N.O.)
36-37: push button inside UP (N.O.)
42-43: internal-push button STOP (N.C.)
40-41: push button outside Down (N.O.)
34-35: push button outside UP (N.O.)
32-33: limit-switch DOWN (N.C.)
30-31: limit-switch UP (N.C.)
28-29: limit switch half-open (N.C.)
10: ground safety photobeam transmitter
11: +24 safety photobeam transmitter
12: ground safety photobeam transmitter
13: +24 safety photobeam transmitter
14: ground safety photobeam receiver
15: +24 safety photobeam receiver
16-17: safety photo beam outside (N.C.)
18-19: safety photo beaminside (N.C.)
20-21: security limit switch UP (N.C.)
22-23: security limit switch DOWN (N.C.)
24-25: 'Wicket Gate' - motor thermoswitch (N.C.)
26-27: safety devices (e.g.wire rope failure) (N.C.)
R2
D5
R3
D6
+ +
- -
52
50
48
46
44
42
40
-
+
-
53
51
49
47
45
43
41
+
38
36
34
32
30
28
39
37
35
33
31
29
57
55
56
54
}(N.C.)
Power supply
photo beam
ST10
ST9
ST8
ST7
ST6
ST5
ST4
ST3
ST2
ST1
ST13
ST11
ST12
ST16
ST15
ST14
Connection keypad (flat cable)
Setting
Europe-France
DOWN
UP
J1 UK
}
}
}outside
inside
inside &
outside
Set Jumper if Comfort module
is connected
Danger Area
visible
}
Connection diagramme mainboard DC 3 de Luxe
d
e
L
u
x
e
Warranty-document
On the below described product we grant a warranty of
2 years
Type: DC 3 ECO - Standard - de Luxe
Production date: ____________________________________________________
Sales date: ____________________________________________________
Dealers adress:
industrial controls
®
industrial controls
®
334
Instructions for Assembly and Use
Industrial Door Control
DC 3 ECO
Art. 509.3000.40
The door control is provided for the operation of sectional-, folding-,DC 3 ECO
rollershutter- and swingdoors.
All standard safety elements connectable.
By using the pushbutton elements on the housing there is no need to mount a
triple pushbutton unit inside.
To open or close the door just push the corresponding button of the remote con-
trol rsp. the button on the DC 3 - housing or on the outside push button unit.
If a radio- and Comfort module is installed the door can also be started or stopped
via hand-held-transmitter.
The most important characteristics of the DC 3 ECO are:
Simple operation, programming and assembly.
Water-protected enclosure (IP65)
Enough space for cabeling
A maximum of safety:
radio control (with Hopping Code) - optional
refering to EU-guidelines for doors and shutters
several safety elements connectable
E
C
O
Technical Data:
Supply voltage 3 x 400 V AC 50 Hz 15 A
Outputs motor 2 x 3 NO relay contacts,
400 V / 6 A
Wiring 1.5 mm2max.,
Operating- -20 ˚C to +60 ˚C
temperature
Caution:
During installation all elements have to be switched tension-free
All installations and service works have to be done by authorized personell only.
The relevant national and local standards and guidelines have to be respected.
Control lamp (optional, only if Comfort module is connected!)
The red LED indicates the most important faults with a flash code:
pre-limit switch defective 1 x flashing
safety edge defective 2 x flashing
limit-switch bottom defective 3 x flashing
safety edge activated 4 x flashing
photo beam defectivet 5 x flashing
resp. light beam interrupted
safety photo beam activated 6 x flashing
safety chain interrupted 7 x flashing
Failure safety photo beam cont. flashing
Function of LED GREEN: LED flashes = door moves DOWN
LED briefly illuminated = door is CLOSED
only
S2


Produktspezifikationen

Marke: Geba Tronic
Kategorie: Garagentoröffner
Modell: DC 3 ECO

Brauchst du Hilfe?

Wenn Sie Hilfe mit Geba Tronic DC 3 ECO benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Garagentoröffner Geba Tronic

Bedienungsanleitung Garagentoröffner

Neueste Bedienungsanleitung für -Kategorien-