GE Profile PDWT500PWW Bedienungsanleitung

GE Waschmaschine Profile PDWT500PWW

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für GE Profile PDWT500PWW (16 Seiten) in der Kategorie Waschmaschine. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/16
GE Consumer & Industrial
Appliances
Installation Instructions
Built-In Dishwasher
If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: www.ge.com
In Canada call 1-800-561-3344 or www.geappliances.ca
imagination at work
IMPORTANT
– The dishwasher MUST
if service is required.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for available
custom panel kits.
FOR YOUR SAFETY
Read and observe all CAUTIONS and WARNINGS
shown throughout these instructions. While performing
installations described in this booklet, gloves and either
safety glasses or goggles should be worn.
A
NT I
BACTE RIA STA RT
RES ET
TO LOCK CONTRO LS
PRESS HEATED
DRY
FOR 3 S EC
ONDS
ENH AN
CEME NTS
S
EL ECTIO NS
SEN SIN
GWAS HIN
GRINS IN
GDRY IN
GSAN IT
IZE DCLEAN
CO OK
WA RE
NOR
MA L
WAS H
SPEED
CYC
LE
CHIN A
CRYS TAL
RIN SE
ON LY 2 4 8
D
EL AY
HO U
RS
ADD ED
HE AT
PRE
WAS H
HEA TED
DRY
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Stainless Steel Tub Models*
*Custom front panel models include a kit that contains a
template, hardware, and panel installation instructions. Refer
to the kit instructions when installing the custom panel.
IMPORTANT
– Observe all governing codes and
ordinances.
•
Note to Installer
– Be sure to leave these instructions for the
consumer’s and local inspector’s use.
•
Note to Consumer
– Keep these instructions with your
Owner’s Manual for future reference.
•
Skill Level
– Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills.
Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the GE Appliance Warranty. See warranty information.
•
Completion Time – 1 to 3 Hours
. New installations require
more time than replacement installations.
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
STOP
PARTS SUPPLIED WITH
INSTALLATION KIT:
Two #8-18 x 5/8" Phillips special head screws, to
secure dishwasher to underside of countertop or
sides of cabinets.
Junction box cover and #10-1/2" hex head screw
Side and top trim
Trim Panel Accessory Kit (not shown).
Model PDW9700 only
Sound upgrade kit (some models)
Drain hose (78") , drain hose hanger and hose
clamp
Literature, Product Samples and/or coupons
Hard water test strip (Models with Bulk Dispenser)
Installation Preparation
TOOLS YOU WILL NEED:
Phillips head screwdriver
1/4" and 5/16" nutdriver
6" Adjustable wrench
Level
Carpenters square
Measuring tape
Safety glasses
Flashlight
Bucket to catch water when flushing the line
15/16" socket
Gloves
For New Installations Only:
Tubing cutter
Drill and appropriate bits
Hole saw set
MATERIALS YOU WILL NEED:
Ferrule, compression nut and 90° Elbow (3/8" NPT
external thread on one end, opposite end sized to
fit water supply)
Thread seal tape
UL Listed wire nuts (3)
Materials For New Installations Only:
Air gap for drain hose, if required
Waste tee for house plumbing, if applicable
Electrical cable or power cord, if applicable
Screw type hose clamps
Strain relief for electrical connection
Hand shut-off valve
Water line 3/8" min. copper
Coupler for extending drain line, if applicable
GPF10L 10' drain hose, if needed
#8 Phillips
Special Head Screws
5/8” long
Hose Clamp
Drain Hose (78")
Trim Pieces
Hand
Shut-Off
Valve
90° Elbow,
Ferrule and
Compression Nut
Thread
Seal Tape
Wire Nuts (3)
Hot Water Line
Electrical Cable
(or Power Cord, if applicable)
Waste Tee
Coupler
Air
Gap
Screw Type
Hose Clamps
Strain Relief
Phillips
Head
Screwdriver
1/4" and
5/16" Nutdriver
Level
Carpenters
Square
1/4" and
15/16" Socket
6" Adjustable
Wrench
Tubing Cutter
Measuring Tape
Safety Glasses
Flashlight
Gloves
Bucket
Hole Saw Set
Drill and Bits
2
Drain Hose Hanger
#10 Hex Head
J-Box Screw
1/2" long
Sound Upgrade Kit
(Some Models)
GPF10L
10' Drain Hose
Junction
Box Cover
Screw Kit
Hard Water Test Strip
(Models with
Bulk Dispenser)
Side Trim
Top Trim
Side Trim
3
Installation Preparation–Enclosure
PREPARE DISHWASHER ENCLOSURE
Figure A
To reduce the risk of shock, fire, or injury
to persons, the installer must ensure that
the dishwasher is completely enclosed at
the time of installation.
WARNING
• The rough cabinet opening must have a minimum width and
depth of 24" and height of 34-1/2" ± 1/4" from the fl oor to the
underside of the countertop.
• The back wall should be free of pipes or wires.
• Adjacent cabinets should be square and plumb to ensure a
good fi t. Refer to Figure A
• For a corner installation, allow 2" minimum clearance
between the dishwasher and the adjacent wall.
• Provide at least 28-3/8" in front of the dishwasher to allow the
dishwasher door to open fully. Refer to Figure B
• Make sure the fl oor is level inside the opening and even with
the fi nished fl oor of the kitchen. This will facilitate removal of
the dishwasher at a later date for service, if needed.
Special consideration for a dishwasher installed on a
elevated platform
The elevated platform must be flat and level.
Cabinets
Square
and
Plumb
Floor MUST
be Even with
Room Floor
This Wall Area
must be Free of
Pipes or wires
Plumbing and Electric Service
Must Enter Shaded Area
34-1/2" ± 1/4"
Underside of
Countertop
to Floor
24"
Minimum
24"
Minimum
5" 5"
4" 4"
6"
Figure B
• The dishwasher must be installed no more than
10 feet from sink for proper drainage.
• The dishwasher must be fully enclosed on the top, sides, and
back.
• The dishwasher must not support any part of the enclosure.
2" Minimum
Countertop
Dishwasher
28-3/8" Minimum
Clearances:
n a corner installation, provide at
east 2" clearance between the
dishwasher and the adjacent
cabinet, wall, or other appliance.
Provide at least 28-3/8" of clearance
n front of the dishwasher.

Produktspezifikationen

Marke: GE
Kategorie: Waschmaschine
Modell: Profile PDWT500PWW

Brauchst du Hilfe?

Wenn Sie Hilfe mit GE Profile PDWT500PWW benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Waschmaschine GE

GE

GE GSD3715FAA Bedienungsanleitung

16 Oktober 2024
GE

GE GSD6700GCC Bedienungsanleitung

15 Oktober 2024
GE

GE GLD5706VCC Bedienungsanleitung

8 Oktober 2024
GE

GE GLDL500NCC Bedienungsanleitung

7 Oktober 2024
GE

GE Profile PDWT500PWW Bedienungsanleitung

6 Oktober 2024
GE

GE ZBD8900PII Bedienungsanleitung

6 Oktober 2024
GE

GE GSD2200GWW Bedienungsanleitung

6 Oktober 2024
GE

GE GSD2020ZBB Bedienungsanleitung

4 Oktober 2024
GE

GE ZBD5700FBB Bedienungsanleitung

3 Oktober 2024
GE

GE EDW6160NSS Bedienungsanleitung

2 Oktober 2024

Bedienungsanleitung Waschmaschine

Neueste Bedienungsanleitung für -Kategorien-

Candy

Candy CS 15102D3-80 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WTIE148 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WISE126R Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WISE126B Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WISE126 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WISA105 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WISA106 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WIA107 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WDIE14106 Bedienungsanleitung

16 Oktober 2024
Electrolux

Electrolux EWW12832 Bedienungsanleitung

16 Oktober 2024