GE GHDA485NCS Bedienungsanleitung

GE Waschmaschine GHDA485NCS

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für GE GHDA485NCS (16 Seiten) in der Kategorie Waschmaschine. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/16
GE Consumer & Industrial
Appliances
I
n
s
t
a
l
l
a
i
o
n
I
n
s
t
r
u
c
t
i
o
n
s
Bu
ilt-In Dishwasher
I
f you have questions, call 800.GE.CARES (800.432.27
37) or visit our website at
: www.ge.com
IMPORTANT
– The dishwasher MUST be installed
to allow for future removal from the enclosure if service is
required.
f you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for available
custom panel kits.
FOR YOUR SAFETY
Read and observe all CAUTIONS and WARNINGS shown
throughout these instructions. While performing
installations described in this booklet, gloves, safety glasses
or goggles should be worn.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
IMPORTANT
– Observe all governing codes and
ordinances.
•
Note to Installer
– Be sure to leave these instructions for the
consumer’s and local inspector’s use.
•
Note to Consumer
– Keep these instructions with your
Owner’s Manual for future reference.
•
Skill Level
– Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills.
Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the GE Appliance Warranty. See warranty information.
•
Completion Time – 1 to 3 Hours
. New installations require
more time than replacement installations.
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
TOOLS YOU WILL NEED:
®
Phillips head screwdriver
®
1/4" and 5/16" nutdriver
®
6" Adjustable wrench
®
Level
®
Carpenters square
®
Measuring tape
®
Safety glasses
®
Flashlight
®
Bucket to catch water when fl ushing the line
®
15/16" socket (optional for skid removal)
®
Gloves
For New Installations Only:
®
Tubing cutter
®
Drill and appropriate bits
®
Hole saw set
90° Elbow,
Ferrule and
Compression Nut
Wire Nuts (3)
Waste Tee
Electrical Cable
(or Power Cord, if applicable)
Hot Water Line
Hand
Shut-Off
Valve
Side and Top Trim Pieces on some models
Hole Saw Set
Level
Thread
Seal Tape
Air Gap
Strain Relief
Drain Hose
Hose Clamp
1/4" and 5/16"
Nutdriver
15/16" Socket
Bucket
Tubing Cutter
Drill and Bits
Flashlight
Gloves
Phillips
Head
Screwdriver
Carpenters
Square
6"
Adjustable
Wrench
Safety Glasses
Installation Preparation
2
Drain Hose Hanger
Measuring Tape
PARTS SUPPLIED
IN INSTALLATION PACKAGE:
Two #8-18 x 5/8" Phillips special head screws, to
secure dishwasher to underside of countertop.
Junction box cover and #10 hex head screw
Hose Clamp
Drain hose (approximately 78" long)
Drain hose hanger
Side and top trim pieces (some models)
Literature, samples and/or coupons
MATERIALS YOU WILL NEED:
Ferrule, compression nut and 90° Elbow (3/8"NPT
external thread on one end, opposite end sized
to fit water supply)
Thread seal tape
UL Listed wire nuts (3)
GPF65 side mount kit if countertop is
granite or similar material
Materials Needed for
New Installations:
Air gap for drain hose, if required
Waste tee for house plumbing, if applicable
Electrical cable or power cord
Screw type hose clamp
Strain relief for electrical connection
Hand shut-off valve (recommended)
Water line–3/8" minimum copper tubing
GPF10L drain hose
(10' long
)
, if needed
Junction
Box Cover
GPF65
Side-Mount
Bracket Kit
#8 Phillips
Special
Head Screws
5/8" long
Screw Kit
#10
Hex- Head
J-Box Screw
1/2" long
Optional
10' Drain Hose
GPF10L
Hose Clamp
Method 1 – Air Gap with Waste Tee or Disposer
An air gap must be used when required by local codes and ordi-
nances. The air gap must be installed according to manufacturer’s
instructions.
PREPARE DISHWASHER ENCLOSURE
• The rough cabinet opening must be at least 24" deep, 24"
wide and approximately 34-1/2" high from floor to underside
of the countertop.
CLEARANCES:
When
installed into a corner,
allow 2" min. clearance
between dishwasher
and adjacent cabinet,
wall or other appliances.
Allow 28-3/8" min. clear-
ance from the front of
the dishwasher for door
opening. Figure B
DRAIN REQUIREMENTS
• Follow local codes and ordinances.
• Do not exceed 10' distance to drain.
NOTE:
Air gap must be used, if waste tee or disposer
connection is less than 18" above floor to prevent siphoning.
DETERMINE DRAIN METHOD
The type of drain installation depends on the following
questions.
®
Do local codes or ordinances require an air gap?
®
Is waste tee less than 18" above floor?
If the answer to either question is YES, Method 1 MUST
be used.
• If the answers are NO, either method may be used.
CABINET PREPARATION
• Drill a 1-1/2" diameter hole in the cabinet wall within
the shaded areas shown in Figure A for the drain hose
connection. The hole should be smooth with no sharp edges.
IMPORTANT
–
When
connecting drain line to disposer,
check to be sure that drain plug has
been removed. DISHWASHER WILL
NOT DRAIN IF PLUG IS LEFT IN PLACE.
Method 2 – “High Drain Loop” with Waste Tee or Disposer
Tip: Avoid unnecessary service call charges
Always be sure disposer drain plug has been removed before
attaching dishwasher drain hose to the disposer.
Figure D
• The dishwasher must be installed so that drain hose is no
more than 10' in length for proper drainage.
• The dishwasher must be fully enclosed on the top, sides and
back, and must not support any part of the enclosure.
24"
Min.
This Wall Area
must be Free
of Pipes or
wires
Plumbing and Electric Service
Must Enter Inside This Area
34-1/2"1/4"
Underside of
Countertop
to Floor
4"
24"
Min.
6"
5" 5"
4"
Cabinets
Square
and
Plumb
Floor MUST be Even
With Room Floor.
32"
Min.
18"
Min.
Drain Hose Hanger
Figure B
Clearance for Door
Opening 2" Minimum
Countertop
Dishwasher
28-3/8"
Figure A
Figure C
Installation Preparation
3
Remove
Drain
Plug
WARNING
To reduce the risk of electric shock,
fi re, or injury to persons, the installer
must ensure that the dishwasher is
completely enclosed at the time of
installation.
32"
Min.
18"
Min.
Drain Hose Hanger

Produktspezifikationen

Marke: GE
Kategorie: Waschmaschine
Modell: GHDA485NCS

Brauchst du Hilfe?

Wenn Sie Hilfe mit GE GHDA485NCS benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Waschmaschine GE

GE

GE GSD3715FAA Bedienungsanleitung

16 Oktober 2024
GE

GE GSD6700GCC Bedienungsanleitung

15 Oktober 2024
GE

GE GLD5706VCC Bedienungsanleitung

8 Oktober 2024
GE

GE GLDL500NCC Bedienungsanleitung

7 Oktober 2024
GE

GE Profile PDWT500PWW Bedienungsanleitung

6 Oktober 2024
GE

GE ZBD8900PII Bedienungsanleitung

6 Oktober 2024
GE

GE GSD2200GWW Bedienungsanleitung

6 Oktober 2024
GE

GE GSD2020ZBB Bedienungsanleitung

4 Oktober 2024
GE

GE ZBD5700FBB Bedienungsanleitung

3 Oktober 2024
GE

GE EDW6160NSS Bedienungsanleitung

2 Oktober 2024

Bedienungsanleitung Waschmaschine

Neueste Bedienungsanleitung für -Kategorien-

Candy

Candy CS 15102D3-80 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WTIE148 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WISE126R Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WISE126B Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WISE126 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WISA105 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WISA106 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WIA107 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia WDIE14106 Bedienungsanleitung

16 Oktober 2024
Electrolux

Electrolux EWW12832 Bedienungsanleitung

16 Oktober 2024