Garmin VIRB Remote Bedienungsanleitung

Garmin Fernbedienung VIRB Remote

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Garmin VIRB Remote (14 Seiten) in der Kategorie Fernbedienung. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/14
VIRB™ Remote Instructions.............................................................................................................. 2
Instructions de la télécommande VIRB™.......................................................................................... 4
VIRB™ Istruzioni del telecomando.................................................................................................... 6
VIRB™ Fernbedienung – Anweisungen............................................................................................ 8
VIRB™ Instrucciones del mando a distancia................................................................................... 10
Instruções do controlo remoto VIRB™............................................................................................ 12
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. VIRB™ and ANT+™ are trademarks of Garmin Ltd. or its subsidiaries. These
trademarks may not be used without the express permission of Garmin.
This product is ANT+™ certified. Visit for a list of compatible products and apps.www.thisisant.com/directory
July 2014 190-01627-90_0DPrinted in Taiwan
TA-2013/2179
TRA
REGISTERED No:
ER0127480/14
DEALER No:
DA0061884/11
VIRB™ Remote Instructions
Remote Overview
ÀRecord key. Select to record video on connected devices.
ÁPhoto key. Select to capture a photo on connected devices.
ÂStop key. Select to stop recording video on connected devices.
ÃStatus LED.
Status LED
LED Activity Status
Flashing green Searching for a paired device.
Alternating red and green Attempting to pair with a device.
12 rapid green flashes Successfully paired with a device.
Four rapid green flashes Successfully sent a command to a device.
Four rapid red flashes Failed to send a command to a device.
Flashing red Device is recording video.
Pairing the Remote with Your Device
The first time you connect the VIRB remote to your VIRB
device, you must pair the remote with your device.
1On the VIRB device, select > > to SETUP Remote Remote
turn on the remote control feature.
2On the VIRB remote, select any key.
The status LED starts flashing green.
3On the VIRB remote, hold two keys simultaneously until the
status LED starts alternating green and red, and release the
keys.
The remote searches for your VIRB device. When the
remote pairs successfully, the status LED flashes green 12
times.
After the remote is paired, it connects to your device whenever
the device is in range and turned on.
Using the Mounts
Several mounts are available for your remote, either included
with the product or as an optional accessory. The mounts allow
you to attach the remote to your body, your bike, or other
objects.
• Align two of the notches À with the sides of the mount, and
press the remote into the mount until it clicks.
• Press gently on the release tab Á, and lift the remote from
the mount.
Replacing the Battery
WARNING
Do not use a sharp object to remove batteries.
Keep the battery away from children.
Never put batteries in mouth. If swallowed, contact your
physician or local poison control center.
Replaceable coin cell batteries may contain perchlorate
material. Special handling may apply. See
www.dtsc.ca.gov.hazardouswaste/perchlorate.
CAUTION
Contact your local waste disposal department to properly
recycle the batteries.
Before you can replace the battery, you must have a small
Phillips screwdriver, a small flat screwdriver, and a CR2032
lithium coin-cell battery.
1Using a Phillips screwdriver, remove the three screws from
the back plate À.
2Remove the back plate from the remote.
3Wrap the end of a small flat screwdriver with tape.
The tape protects the battery, battery compartment, and
contacts from damage.
4Carefully pry the battery from the back plate.
5Install the new battery into the back plate with the positive
side facing down.
6Verify the gasket Á is fully seated in the groove.
2
7Replace the backplate, aligning the post  with the gap in
the circuit board Ã.
8Replace and tighten the three screws.
NOTE: Do not overtighten.
Specifications
Battery type User-replaceable CR2032, 3 volts
Battery life Up to 1.5 years (1 hour per day)
Operating temperature
range
From -10° to 50°C (from 14° to 122°F)
Radio frequency/protocol 2.4 GHz ANT+™ wireless communications
protocol
Water rating 5 ATM*
*The device withstands pressure equivalent to a depth of
50 meters.
3

Produktspezifikationen

Marke: Garmin
Kategorie: Fernbedienung
Modell: VIRB Remote

Brauchst du Hilfe?

Wenn Sie Hilfe mit Garmin VIRB Remote benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Fernbedienung Garmin

Garmin

Garmin GHS 20 Bedienungsanleitung

4 Januar 2024
Garmin

Garmin VIRB Remote Bedienungsanleitung

25 Juni 2023
Garmin

Garmin eBike Remote Bedienungsanleitung

25 Juni 2023
Garmin

Garmin GHS 20i Bedienungsanleitung

27 Oktober 2022

Bedienungsanleitung Fernbedienung

Neueste Bedienungsanleitung für -Kategorien-

Neewer

Neewer RT112 Bedienungsanleitung

8 Oktober 2024
Neewer

Neewer RT113 Bedienungsanleitung

8 Oktober 2024
Logitech

Logitech Harmony 600 Bedienungsanleitung

5 Oktober 2024
Furman

Furman RS-2 Bedienungsanleitung

5 Oktober 2024
Hannspree

Hannspree YES-001016 Bedienungsanleitung

3 Oktober 2024
Canon

Canon RS-80N3 Bedienungsanleitung

3 Oktober 2024
Alpine

Alpine RUE-M300 Bedienungsanleitung

2 Oktober 2024
Meliconi

Meliconi universal 4 Bedienungsanleitung

23 September 2024
Energy Sistem

Energy Sistem 4100 Bedienungsanleitung

23 September 2024
Humax

Humax RS505 Bedienungsanleitung

23 September 2024