Garmin gWind Race Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Garmin gWind Race (46 Seiten) in der Kategorie Marine. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/46
gWind Race™ Installation Instructions................................................................................................2
Instructions d'installation du gWind Race™........................................................................................ 5
gWind Race™ Istruzioni di installazione............................................................................................. 8
gWind Race™ – Installationsanweisungen....................................................................................... 11
Instrucciones de instalación de gWind Race™................................................................................. 14
Instruções de instalação do gWind Race ™...................................................................................... 17
gWind Race™ installatie-instructies.................................................................................................. 20
gWind Race™ Installationsvejledning............................................................................................... 23
gWind Race™ asennusohjeet........................................................................................................... 26
Installeringsinstruksjoner for gWind Race™..................................................................................... 29
gWind Race™ – installationsinstruktioner......................................................................................... 32
Instrukcja instalacji urządzenia gWind Race™................................................................................. 35
Pokyny pro instalaci zařízení gWind Race™.................................................................................... 38
Upute za montažu uređaja gWind Race™........................................................................................ 41
gWind Race™ 安装说明.................................................................................................................... 44
Garmin®, the Garmin logo, and Nexus® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. gWind Race
™, NexusRace™, GND™, and GMI™ are trademarks of Garmin
Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.
NMEA 2000® and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association.
February 2016 190-01723-97_0CPrinted in Taiwan
TA-2013/1725
TA-2013/2433
gWind Race
™
Installation Instructions
This wind transducer provides wind speed and wind angle
information to a NMEA 2000® network on your boat. A Garmin®
GND™ 10 must be used to send data from this device to a
NMEA 2000 network.
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
Use caution when working from heights.
Registering Your Device
Help us better support you by completing our online registration
today.
• Go to .http://my.garmin.com
• Keep the original sales receipt, or a photocopy, in a safe
place.
Installing the Propeller
1Ensure the shaft À lines up correctly with the slot on the
propeller.
The socket on the propeller fits only one way on the shaft.
2Press on the propeller until it is seated on the device.
3Install the set screw Á to hold the propeller securely to the
device.
Mounting Considerations
When selecting a mounting location for the wind transducer,
observe these considerations.
• The wind transducer can be installed in either a pre-existing
pole mount on your mast, or in the included mounting
bracket.
• If you are installing the included mounting bracket, it should
be mounted on a horizontal surface on the mast head.
• If there is not a horizontal surface on the mast head, an
appropriate shim must be added to create a horizontal
surface.
• The wind transducer should be installed with the cable facing
the front of the boat, parallel to the center line.
NOTE: If you do not mount the device with the cable facing
the exact front of the boat, you must configure the orientation
to receive accurate wind-angle data (Adjusting the
Orientation, page 3).
Installing the Mounting Bracket
The included bracket can be used to mount the device if you do
not have a pole mount pre-installed on your mast.
1Using the mounting bracket as a template, mark the pilot hole
locations.
2Using a 4.5 mm (11/64 in.) bit, drill the pilot holes.
3Fasten the mounting bracket to the surface using the
included screws.
Securing the Device in the Mounting Bracket
The included bracket can be used to mount the device if you do
not have a pole mount pre-installed on your mast.
1Slide the pole À into the mounting bracket
Á, and turn it until
the cable  points toward the front of the boat, parallel to the
center line.
NOTE: If you do not mount the device with the cable facing
the front of the boat, exactly parallel to the center line, or if
you mount the device with the cable facing the back of the
boat, you must configure the orientation to receive accurate
wind-angle data (Adjusting the Orientation, page 3).
2Holding the pole securely, use a 5.5 mm (
7/32
in.) bit to drill a
hole halfway through the pole, drilling through the hole in one
side of the mounting bracket.
3Insert the included hex screw à through the hole you drilled
in step 2.
This holds the pole in place while you drill another hole.
4Drill through the other half of the pole by drilling through the
hole on the other side of the mounting bracket
Ä.
5Push the hex screw completely through both holes and
secure it using the included lock nut.
Connection Considerations
This device must connect to a Garmin GND 10 to communicate
with the NMEA 2000 network on your boat.
2 Installation Instructions
Item Description
ÀgWind™ device
ÁIncluded Nexus® mast cable with a field-installable connector
ÂGND 10
ÃNMEA 2000 network
Nexus Connection Considerations
If you change from a Nexus wind sensor to the gWind sensor,
you must move the mast cable from the wind port to the network
port on the Nexus server on pins 5, 6, 7, and 8. The network
server is NX2, and the classic server is BUS. See the Nexus
device manual for more information.
Installing the Nexus Field-Installable Connector
You must use the included field-installable connector to create
the appropriate cable length for your installation.
1Connect the finished end of the included bulk cable to the
wind transducer on the mast.
2Route the bare end of the cable to the location of the
GND 10.
3Leaving an appropriate amount of slack, cut the bare end of
the wire, remove the casing, and strip the individual wires.
4Disassemble the field-installable connector and place the
pressing screw À, pinch ring Á, seal Â, and sleeve à on the
cable Ä.
5Using the screws on the back of the connector
Å, connect
each wire to the appropriate terminal.
Terminal Number Wire Color
ÊGreen
ËYellow
ÌBare wire
ÍWhite
6Screw the sleeve onto the connector.
7Slide the seal into the sleeve and slide the pinch ring over the
seal.
8Screw the pressing screw into the sleeve to complete the
assembly of the field-installable connector.
9Connect the field-installable connector to either NEXUS port
on the GND 10.
Configuring the Wind Transducer
Before you can configure the wind transducer, it must be
connected through a GND 10 to a NMEA 2000 network with a
Garmin marine instrument, such as a GMI™ 20. Refer to the
marine instrument owner's manual for more information on
configuring NMEA 2000 devices.
1On the marine instrument, go to the NMEA 2000 settings.
2Select the name of the device (GND 10) to configure.
Adjusting the Orientation
You should adjust this setting if the sensor does not face the
front of the boat, exactly parallel to the center line.
NOTE:
The opening where the cable connects to the pole
indicates the front of the sensor.
1On the marine instrument, from the NMEA 2000 settings,
select the device name (GND 10).
2Select Wind Angle Offset.
3Estimate the angle, in degrees clockwise around the mast, by
which the sensor points away from the center of the front of
the boat:
• If the sensor is facing starboard, the angle should be
between 1 and 180 degrees.
• If the sensor is facing port, the angle should be between
181 and 360 degrees.
4Select the angle observed in step 3.
5Select Done.
Adjusting the Wind Angle Filter
You should adjust this setting to change the responsiveness of
the display to changes in the wind direction.
1On the marine instrument, from the NMEA 2000 settings,
select the device name (GND 10).
2Select Wind Angle Filter.
3Select an option:
• Select Off to turn off the filter and make the display the
most responsive to changes in the wind angle.
• Select and adjust the value. Select a higher number to On
increase the responsiveness of the display to changes in
the wind angle, or select a lower number to decrease the
responsiveness.
• Select Auto to automatically adjust the filter settings
based on wind conditions.
4Select Done.
Adjusting the Wind Speed Filter
You should adjust this setting to change the responsiveness of
the display to changes in the wind speed.
1On the marine instrument, from the NMEA 2000 settings,
select the device name (GND 10).
2Select Wind Speed Filter.
3Select an option:
• Select Off to turn off the filter and make the display the
most responsive to changes in the wind speed.
• Select On and adjust the value. Select a higher number to
increase the responsiveness of the display to changes in
the wind speed, or select a lower number to decrease the
responsiveness.
• Select Auto to automatically adjust the filter settings
based on wind conditions.
4Select Done.
Advanced Calibration
Advanced calibration tools are available for this device using a
connected PC running the NexusRace™
software. You can
download the software from . You must www.garmin.com
connect the PC to the GND 10. For more information, see the
GND 10 Installation Instructions.
Installation Instructions 3
Produktspezifikationen
| Marke: | Garmin |
| Kategorie: | Marine |
| Modell: | gWind Race |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Garmin gWind Race benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Marine Garmin
5 August 2024
7 Juli 2024
6 Juli 2024
6 Juli 2024
5 Juli 2024
5 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
3 Juli 2024
Bedienungsanleitung Marine
- Marine Humminbird
- Marine Kenwood
- Marine Silva
- Marine Furuno
- Marine Lowrance
- Marine Simrad
- Marine Icom
- Marine President
- Marine Rockford Fosgate
- Marine Klarfit
- Marine IVT
- Marine Navionics
- Marine Dickinson Marine
- Marine Digital Yacht
- Marine Eagle
- Marine Easy
- Marine Echotec
- Marine Efoy
- Marine Fastnet
- Marine Fusion
- Marine Geonav
- Marine Interphase
- Marine Katadyn
- Marine KVH
- Marine Lofrans
- Marine Lorenz
- Marine Nasa
- Marine Navico
- Marine Nordwest-funk
- Marine Plastimo
- Marine Polmar
- Marine Raymarine
- Marine Raytheon
- Marine Sailtron
- Marine SEAFARER
- Marine Standard Horizon
- Marine WEST SYSTEM
- Marine AdvanSea
- Marine Alphatron
- Marine BandG
Neueste Bedienungsanleitung für -Kategorien-
5 Oktober 2024
24 September 2024
22 September 2024
21 September 2024
18 September 2024
27 August 2024
27 August 2024
27 August 2024
27 August 2024
26 August 2024