Futaba SBD-2 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Futaba SBD-2 (2 Seiten) in der Kategorie Funkgesteuertes Spielzeug. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
S.BUS Decoder
SBD-2
Connection
Channel selection
*You should use an EXT battery, when using
many servos.
*If S.BUS/S.BUS2 servo
is connected to SBD-2,
CH written in S.BUS/
S.B US2 servo will
ignore. S.BUS/S.BUS2
servo is operated by
CH of SBD-2.
Mini screwdriver used
* #0 of rotary switch
position does not
use it.
* DG1, D G2 : Swi t c h chan n el ou t p u t
connector
Conventional servos(other than S.BUS servo)
Eight servos are connectable.
SBD-2 can change the output
CH by rotary switch.
External battery
(For servos)
Ext battery switch
C o n n e c t th e sho rt i n g p i n s
supplied when power is shared
with the receiver power source.
SBD-2
S.BUS / S.BUS2
Receiver
To S.BUS / S.BUS2
port
Rotary switch position
1 2 3 4 5 6 7 8 9
1 CH1 CH9 CH8 CH4 CH9 CH9 CH8 CH4 CH1
2 CH2 CH10 CH9 CH5 CH10 CH10 CH9 CH5 CH2
3 CH3 CH11 CH10 CH6 CH11 CH11 CH10 CH6 CH3
4 CH4 CH12 CH11 CH7 CH12 CH12 CH11 CH7 CH4
5 CH5 CH13 CH12 CH8 CH13 CH13 CH12 CH8 CH5
6 CH6 CH14 CH13 CH9 CH14 CH14 CH13 CH9 CH6
7 CH7 CH15 CH14 CH10 CH15 DG1 DG1 DG1 DG1
8 CH8 CH16 CH15 CH11 DG1 DG2 DG2 DG2 DG2
Servo output connectors
SBD-2 LED state
OFF OFF
ON
S.BUS receive
error Blink
S. BUS
reception ON
Always use in the state in which the SBD-2 is
firmly attached to the fuselage of the airplane or
helicopter.
■ There is the danger of loss of control and crashing
if the connector is disconnected by vibration and
shock.
When using analog servos, always use in the state
in which the receiver is normal mode.
There is the danger of erroneous operation or
damage on the FASST12ch / High-speed mode.
Do not connect an S.BUS/S.BUS2 connector of the
SBD-2 to other than an S.BUS/S.BUS2 connection port.
There is the danger of erroneous operation or
damage.
Do not use the SBD-2 with anything other than an
R/C model.
To ensure that the SBD-2 is functioning as desired,
please test accordingly.
■ Do not y until inspection is complete.
Do not connect shorting pins, when using an Ext
battery.
■ There is the danger of explosion and ignition.
Ensure that the unit is mounted in an area that will
eliminate exposure to fuel, water and vibration.
As with any electronic components, proper
precautions are urged to prolong the life and
increase the performance of the SBD-2.
Allow a slight amount of slack in the SBD-2 cables
and fasten them Eat a suitable location to prevent
any damage from vibration during ight.
Do not connect either
a switch or battery in
this manner.
When a connector
is inserted like the
left, it short-circuits
and there is danger
of e x p lo s i o n an d
ignition.
WARNNG
INSTRUCTION MANUAL
Before using your new SBD-2, please read this manual
thoroughly and use the system properly and safely.
After reading this manual, store it in a safe place.
Thank you for purchasing an SBD-2, S.BUS decoder. The
SBD-2 is a converter for using conventional servos (other
than S.BUS servo) with the S.BUS/S.BUS2
system. The
SBD-2 connects to the receiver output of a S.BUS/S.BUS2
system and eight servos can be used.
SBD-2 can change the output CH from 9 groups select by
rotary switch. SBD-2 can use EXT battery (for servos).
Applicable receiver: S.BUS/S.BUS2
system receiver only
Usage Precautions
Connections and Name of Each Part of the SBD-2
Futaba Corp. will not be responsible for damage
caused by combination with other than Futaba
Genuine parts.
Input connector
●C o n n e c t s  t o t h e S . B U S /
S.BUS2 port of the receiver.
Rotary switch
Servo output connectors (1~8)
●Connecttheservos.
External battery
connector
(EXT.BATT)
Connect the shorting pins
supplied when power is
shared with the receiver
power source.
Mini screwdriver
Monitor LED
©Copyright 2014. No part of this manual may be reproduced in any form without prior permission. The contents of this
manual are subject to change without prior notice. While this manual has been carefully written, there may be inadvertent
errors or omissions. Please contact our service center if you feel that any corrections or clarifications should be made.
FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan
©FUTABA CORPORATION 2014, 8 (1)
[SBD-2 Ratings]
Dimensions:
29.6mm x 39.3mm x 15.8mm
(1.17in. x 1.55in. x 0.62in.)
(excluding protruding)
Weight:
14.2g (0.5 oz.)
Power requirement:
4.8V 7.4V
Monitor LED
OK


Produktspezifikationen

Marke: Futaba
Kategorie: Funkgesteuertes Spielzeug
Modell: SBD-2

Brauchst du Hilfe?

Wenn Sie Hilfe mit Futaba SBD-2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Funkgesteuertes Spielzeug Futaba

Bedienungsanleitung Funkgesteuertes Spielzeug

Neueste Bedienungsanleitung für -Kategorien-