Foscam FN7108HE Bedienungsanleitung
Foscam
Videorecorder
FN7108HE
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Foscam FN7108HE (3 Seiten) in der Kategorie Videorecorder. Dieser Bedienungsanleitung war für 27 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/3
54 6 7
1 2 3
Quick Setup Guide
Network Video Recorder
Model: FN7108HE
V1.0.3
WARNING
Before installing a hard disk drive (HDD), please make sure the power
is disconnected from the NVR.
It is recommended that a hard drive be used in 7200 high-speed or
above.
Power cable
HDD
Data cable
It is recommended to use SATA type of hard disk for recording.
Note
1. Remove the cover from the NVR by unfastening the screws on the
rear and bottom.
2. Connect one end of the data cable and power cable to the
motherboard of NVR and the other end to the HDD.
3. Place the HDD on the bottom of the device and then fasten the
screws on the bottom to x the HDD.
4. Re-install the cover of the NVR and fasten screws.
HD-OUT Video Output
VGA Video Output
Procedure
1. Connect your display to one of the video outputs (VGA or HD-OUT
interface).
2. Connect an external storage device to the USB interface of the NVR as
a backup.
3. Connect a mouse to the USB interface.
4. Some devices need to connect to your router using an Ethernet cable,
including the NVR, PC and IP Camera.
5. Connect the power adapter to the power input port.
Foscam cameras and NVRs require good security practices to
safeguard your privacy. You should regularly change your
camera or NVR password which is the combination of
numbers, letters and symbols.
You should update your camera or NVR regularly. Make sure
your camera or NVR has the latest rmware installed for your
specic model and better experience.
Quick Setup Guide
Power Input Reset USB
USB
Power Switch Ethernet Port
IP Cameras Input Router Computer
Monitor
TV
Mouse
NVR
Screw Pack
DC Power Adapter
Ethernet Cable
Data Wire and Power Wire
of the Hard Drives
Warranty Card
USB Mouse
1. Turn on the power switch on the rear panel.
After the NVR starts up successfully, the power LED and HDD LED
indicators will turn green. The startup page is displayed on the screen.
2. Login page.
Select the Language, Enter the and , then click Username Password
on the button.Login
Default username is
admin with no password
Package Contents
Security Warning
1 Before You Start 2 Hard Disk Installation
3. For the initial log in, the system will prompt you to change your
password. Once done, click the button. OK
4. After modifying the password, you will be taken to the Setup
Wizard.
1. Setting the time. If you don’t want to use the Setup Wizard next
time, uncheck the checkbox. Click the button.Setup Wizard Next
2. Select the HDD you would like to use, then click the Format Hard
Disk button to set up the HDD. Note that this will delete all les on
the HDD.
Select a protocol depending on which IP Camera you have.
FOSCAM protocol: The High Denition (HD) IP Cameras for Foscam.
MJ protocol: The Standard Denition (SD) IP Cameras for Foscam.
ONVIF protocol: IP Cameras which support ONVIF protocol.
3. You can add an IP Camera that is connected to the internet on the
NVR.
You can congure the following information for your IP Camera.
The Setup Wizard can walk you through some important settings on
the NVR.
1. Select Your IP Camera
2. Click Add
3 Device Connection 4 5 Log In Setup Wizard
Input a new password,
then click OK.
Uncheck the checkbox
2. Click Format Hard Disk
3. Click Next
1. Select your HDD
Format Hard Disk
For detailed manuals, tools, etc., please visit foscam.com/downloads.
8 9
12 13 14
1110
15
CE Certificate statement Website:
https://www.foscam.com/company/ce-certificate.html
Exporter and Importer Information Opened to Public:
https://www.foscam.com/company/open-information.html
www.foscam.com
As a result of product upgrades and other reasons, this guide may not be able to
update in time, resulting in inconsistency with the ocial website information,
please take the ocial website(www.foscam.com) information as the standard.
Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd
Addr: 9/F, Block F5, TCL International E City, No.1001
ZhongShanyuan Rd., NanShan District, Shenzhen, China, 518055
To disable recording, click again the button in the channel, or
uncheck the checkbox on the interface. channel Manual Record
Note
The maximum number of 4 playback video channels have been
reached, please deselect other channels rst to continue.
Note
Note
This product supports 32-bit IE8 or later versions and does not
support 64-bit IE browsers. It also supports Apple Safari.
8.1 Network Conguration
8.3 Access to the NVR in WAN
Now you can access to your NVR using the DDNS address, such as
https://domain name:HTTPS port.
As an example: https://a6747.myfoscam.org:443
Click Add New...
If there is a UPnP function in your router.
Choose , make sure that the Forwarding > UPnP Current UPnP Status
is . Enabled
If UPnP has been in the router, you do not need to perform enabled
the following steps.
If UPnP is , you need to select one of the following methods disabled
to congure port forwarding on your router.
For these steps, we will be using the TP-LINK brand wireless router as
an example.
If there is no UPnP function in your router:
You need to manually add port forwarding, refer to the following
steps. You need go to the panel for Forwarding > Virtual Servers
setup.
Power Supply: DC 48V 2.0A 96W
You can also access the NVR or IP Camera directly through the local
network and remotely via manual port forwarding.
4. Repeat the step3 to add multiple IP Cameras. Find your IP Camera in
the , then click the button to complete the IP Camera List Finish
setup wizard.
After the IP Camera is added successfully to the NVR, there are two ways
to enable manual recording functionality when in the Live View mode.
Method 1
Left click the mouse in the channel, and some buttons will pop up as
shown . Click the button to enable recording.
You can see the recording information, include Manual Record, Alarm
Record, Schedule Record.
1. Right click the mouse in the Live View mode, and a shortcut menu
will pop up.
2. Select the to enter the page.Playback Playback
3. Select the time and Video Type of the recording. Check the Channels,
and you can check up to four channels.
4. Click the button. Then you can see the recording video in the Search
Playback page.
Method 2
1. Right click the mouse in the Live View mode, and a shortcut menu
will pop up.
2. Select the to enter the page.Manual Record Manual Record
3. Check the channels for which you want to enable recording. Click the
OK button.
4. Then click the icon to exit the interface.
In the Live View mode, the icon is at the bottom right of the screen
for each channel, indicating recording is on going.
1. Congure network information.
Right click the mouse in the Live View mode, choose Menu >
Settings > Network Network. Check the checkbox, then congure
the network information of the NVR.
It is highly recommended to set the port range from 5000 to 65535,
and the value of the port for each device should be unique.
2. Congure the DDNS.
Right click the mouse in the Live View mode, choose Menu > Settings
> Network DDNS. Check the checkbox. Enable DDNS on the NVR. We
recommend you to use the DDNS by default.
The live view interface will show you the video feed of each IP Camera.
If you have problems with your Foscam device, please contact the
Foscam reseller you purchased from, or you can e-mail the Foscam
headquarter technical support team: support@foscam.com
Your valuable comments and suggestions on improving Foscam
products are welcomed!
Select the Type
Check Network
Set the orHTTP Port HTTPS Port
IP Address: Set it to an IP address of
NVR in the range of the router
address pool, or keep it as default.
Subnet Mask: Keep it as default.
Gateway: Should be the same as the
Router’s IP address.
DNS Server: Should be the same as
the router’s DNS Server address.
Check UPNP Click Save
8.2 Access to the NVR in LAN
Double click the NVR in the list, and your default browser will open up
to the login page.
You can access to the NVR via the browser in LAN.
6
Manual Recording
7
Playback
8 Remote Access
10 Technical Support
Click Save
Check DDNS
Check Enable DDNS
Download the “Equipment Search Tool” from
foscam.com/tools to your computer. Run it, and it will display
information of the NVR on your LAN.
9 Product Performance
Input the port and IP address
of your NVR and click . Save
443
443
7. Click OK
3. Select the Channel
5. Input the and Username
Password of the IP Camera .
4. Enusre that the IP address of the
IP Camera and NVR is on the same
network IP segment, and that the
subnet mask and gateway are the
same as the NVR's.
Click Finish
6. Select the protocol.
Produktspezifikationen
| Marke: | Foscam |
| Kategorie: | Videorecorder |
| Modell: | FN7108HE |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Foscam FN7108HE benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Videorecorder Foscam
17 September 2024
30 Juli 2024
28 Juli 2024
Bedienungsanleitung Videorecorder
- Videorecorder Philips
- Videorecorder Sony
- Videorecorder Panasonic
- Videorecorder Bosch
- Videorecorder Canon
- Videorecorder Linksys
- Videorecorder Technaxx
- Videorecorder Blaupunkt
- Videorecorder Grundig
- Videorecorder Daewoo
- Videorecorder Aiwa
- Videorecorder JVC
- Videorecorder Abus
- Videorecorder EZVIZ
- Videorecorder Imou
- Videorecorder Hitachi
- Videorecorder Toshiba
- Videorecorder Tripp Lite
- Videorecorder TRENDnet
- Videorecorder TP-Link
- Videorecorder Monacor
- Videorecorder Seagate
- Videorecorder D-Link
- Videorecorder Magnum
- Videorecorder Skytronic
- Videorecorder Sylvania
- Videorecorder Navitel
- Videorecorder QNAP
- Videorecorder Digitus
- Videorecorder DataVideo
- Videorecorder LevelOne
- Videorecorder Grandstream
- Videorecorder Tenda
- Videorecorder Synology
- Videorecorder Reolink
- Videorecorder Hikvision
- Videorecorder Planet
- Videorecorder Blackmagic Design
- Videorecorder GeoVision
- Videorecorder Magnavox
- Videorecorder Meridian
- Videorecorder Provision ISR
- Videorecorder Vivotek
- Videorecorder ACTi
- Videorecorder AVer
- Videorecorder AirLive
- Videorecorder Dahua Technology
- Videorecorder Kunft
- Videorecorder Speco Technologies
- Videorecorder Avigilon
- Videorecorder Hanwha
- Videorecorder Axis
- Videorecorder UniView
- Videorecorder Inkovideo
- Videorecorder HiLook
- Videorecorder Mach Power
- Videorecorder Digital Watchdog
- Videorecorder A.C.Ryan
- Videorecorder Aristona
- Videorecorder Milesight
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
14 Oktober 2024
9 Oktober 2024
9 Oktober 2024
7 Oktober 2024
6 Oktober 2024
24 September 2024
23 September 2024
21 September 2024
14 September 2024