Fortinet FortiAP 220B Bedienungsanleitung
Fortinet
Zugangspunkt
FortiAP 220B
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Fortinet FortiAP 220B (2 Seiten) in der Kategorie Zugangspunkt. Dieser Bedienungsanleitung war fĂĽr 39 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
QuickStart Guide
© Copyright 2010 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks
of their respective holders.
Regulatory Compliance
FCC Class B Part 15, / CE Mark
7 August 2010
FortiAP-210B/220B
01-420-127515-20100702
Visit these links for more information and documentation for your Fortinet product:
Technical Documentation - Fortinet Knowledge Center - http://docs.fortinet.com http://kb.fortinet.com
Technical Support - Training Services - http://support.fortinet.com http://campus.training.fortinet.com
If the FortiGate wireless controller’s IP address cannot be determined from the
methods above or if the network uses static IP addresses, do the following:
1. Connect the FortiAP to a separate private switch or hub or directly connect
to your computer via a cross-over cable.
2. Change your computer’s IP address to 192.168.1.3
3. Telnet to IP address 192.168.1.2. This IP address is overwritten if the
FortiAP is connected to a DHCP environment. Ensure that FortiAP is in a
private network with no DHCP server for the static IP address to be acces-
sible.
4. Login with username: and no password.admin
5. Type the following commands to enter static IP address for Access Point.
netmask & gateway information for your network. Replace zzz with the IP
address of the FortiGate Wireless Controller.
cfg –a AP_IPADDR=”xxx.xxx.xxx.xx”
cfg –a AP_NETMASK=”255.255.255.0”
cfg –a IPGW=”yyy.yyy.yyy.yyy”
cfg –a AC_IPADDR_1=”zzz.zzz.zzz.zzz”
6. Save the conîšżguration by typing the following command:
cfg –c . Unplug the FortiAP and plug it back in order for the congura-
tion to take effect.
7. Move the FortiAP to the intended deployment location and connect the
Ethernet cable as described in the Connecting section.
8. In FortiGate controller Web Conîšżg, go to Wireless Controller > Conîšżgura-
tion > Access Point. A successfully discovered unit displays a half-îšżlled
circle symbol.
9. Select the Access Point and click Edit.
10. In the Admin îšżeld, select Enable.
11. In the AP Proîšżle îšżeld, select a proîšżle from the list and click OK.
The conîšżguration is downloaded from the FortiGate unit to the FortiAP and
the Wireless LED lights up.
Note: FortiGate Low encryption units must be matched up with Low Encryp tion
Access Points.
Power Required Adaptor Input 100-240V~ 50/60Hz 0.6A
Output: 12V DC 1.5A –center positive
Ports
1 x 10/100/1000 PoE (IEEE 802.3af)
1 Console127515
1 USB 2.0
Number of radios FortiAP-210B — 1
FortiAP-220B — 2
WiFi 802.11 a, b, g, n
Mount Wall or ceiling
Conîšżguring continued... Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modiîšżcations not expressly approved by the party responsible for com-
pliance could void the user’s authority to operate this equipment.
For operation within 5.15 ~ 5.25GHz frequency range, it is restricted to indoor environment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-
tions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer-
ence received, including interference that may cause undesired operation.
IMPORTANT NOTE: Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmit-
ter.
The availability of some speciîšżc channels and/or operational frequency bands are country dependent
and are îšżrmware programmed at the factory to match the intended destination. The îšżrmware setting is
not accessible by the end user.
Industry Canada Statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Règlement d’Industry Canada
Les conditions de fonctionnement sont sujettes Ă deux conditions:
1) Ce périphérique ne doit pas causer d’interférence et.
2) Ce périphérique doit accepter toute interférence, y compris les interférences pouvant perturber le
bon fonctionnement de ce périphérique.
IMPORTANT NOTE: Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
Caution:
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interfer-
ence to co-channel mobile satellite systems.
LED DescriptionPackage Contents
USB
CONSOLE ETH PoE -48V
AC
Power
Front
Back
Wifi Radio 1
Mode Status Power
DC 12V, 1.5A
+
PoE
Power
Console
port
USB
port
Lock
Wifi Radio 2
Wifi Radio 3
(not in use)
Ethernet
Interface Description
Connecting
Administrator login
Username admin
Password <none>
Default port addresses
Port 1 192.168.1.2
To reset the FortiAP unit to the factory defaults, in the CLI type the command:
factoryreset
Copyr ight 2010 Fort inet Incorporat ed. Al l right s reserv ed.
T radema rks
Product s m entio ned in t his do cument ar e t ra demarks.
Qui ckStart Gu ide
Power Supply
REGISTER
Factory Defaults
LED State Description
PWR
Green The unit is ready and has AC power.
Green Flashing The unit is booting.
Off The unit is off.
Status
Green The FortiAP is being managed by the
FortiGate Wireless Controller.
Amber ashing FortiAP has lost network connection to
the FortiGate wireless controller.
Amber FortiGate wireless controller has been
found but FortiAP is not managed.
Off FortiGate wireless controller has not
been found.
Mode
Green One or more radio in Monitor mode.
Green ashing One or more radio in dedicated Repeat-
er mode. To be implemented in a future
release.
Off No mode selected.
WiFi1
Green Radio 1 enabled.
Green ashing Wireless activity.
Off Radio 1 disabled or off.
WiFi2 (Only
FortiAP-220B)
Green Radio 2 enabled.
Green ashing Wireless activity.
Off Radio 2 disabled or off.
WiFi3 Not in use.
ETH
Green ashing Link activity.
Green Network speed of 1000 Mbps.
Amber Network speed of 10/100 Mbps.
Off Ethernet link unavailable.
Interface Type Speed Protocol Description
Console RJ-45 9600bps RS-232
serial
Optional connection to the
management
computer. Provides
access to the command
line
interface (CLI).
ETH PoE
-48V
IEEE
802.3af
10/100/1000
Base-T
Ethernet POE capable source port.
Power requirement of 15.4
Watts.
USB Type A 2.0 For future use.
Using the provided template and two M3 screws, attach the unit to the wall or
ceiling using the two mounting holes at the bottom of the FortiAP unit. If placing
on desktop, attach the rubber feet to the unit.
Connect the following to the FortiAP unit:
1. Insert a network cable to the ETH PoE -48V port.
• Use straight-through cable for most equipment
• Use cross-over cable if connecting to FortiGate units without auto MDI
detect
2. Insert the other end of the network cable into your LAN Ethernet edge
switch, or directly to the FortiGate Controller.
3. If using PoE, connect the cable to the ETH PoE -48V port.
4. If not using PoE, connect the power adaptor to AC outlet and insert the
power adaptor connector to the FortiAP unit.
Note: Only FortiGate-60B units or higher can act as wireless controllers.
Caution: This device complies with 802.3af PoE speciîšżcation. Do not use any
PoE injectors that are not 802.3af compliant as it may damage this device.
Conîšżguring
The FortiAP is designed to require no conîšżguration in most networks. Zero
Conîšżguration mode works if the FortiAP is directly connected to the FortiGate
performing the Wireless LAN Controller (WLC) functions, or on the same layer-2
network and subnet as the FortiGate.
To enable the FortiAP using Zero Conîšżguration:
1. Connect the network and power cable as described in the Connecting sec-
tion.
2. Once power is applied, the FortiAP goes through boot procedure and re-
quests an IP address from the DHCP server.
3. If the IP address is retrieved successfully, the FortiAP enters discovery
mode to locate a FortiGate wireless controller. The discovery modes are:
• Broadcast
• Multicast
• DHCP option 138
4. If this is the îšżrst time connecting the FortiAP to the controller, only the power
light and Port 0 LED is lit. If the FortiAP has been pre-provisioned in the
controller, the Wireless LED is also lit.
5. Verify that the FortiAP has successfully connected to the controller. In
FortiGate controller Web Conîšżg, go to Wireless Controller > Conîšżguration
> Access Point. A successfully discovered unit displays a half-îšżlled circle
symbol.
6. Select the Access Point and click Edit.
7. In the Admin îšżeld, select Enable.
8. In the AP Proîšżle îšżeld, select a proîšżle from the list and click OK.
The conîšżguration is downloaded from the FortiGate unit to the FortiAP and
the Wireless LED lights up.
Produktspezifikationen
| Marke: | Fortinet |
| Kategorie: | Zugangspunkt |
| Modell: | FortiAP 220B |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Fortinet FortiAP 220B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Zugangspunkt Fortinet
3 September 2024
3 September 2024
17 August 2024
2 August 2024
2 August 2024
30 Juli 2024
28 Juli 2024
28 Juli 2024
26 Juli 2024
22 Juli 2024
Bedienungsanleitung Zugangspunkt
- Zugangspunkt Asus
- Zugangspunkt HP
- Zugangspunkt Macally
- Zugangspunkt ZyXEL
- Zugangspunkt Bosch
- Zugangspunkt Buffalo
- Zugangspunkt Allnet
- Zugangspunkt Devolo
- Zugangspunkt Eminent
- Zugangspunkt Linksys
- Zugangspunkt Netgear
- Zugangspunkt Renkforce
- Zugangspunkt Netis
- Zugangspunkt Aruba
- Zugangspunkt Lindy
- Zugangspunkt Dell
- Zugangspunkt Mercusys
- Zugangspunkt Honeywell
- Zugangspunkt TRENDnet
- Zugangspunkt AVM
- Zugangspunkt Zebra
- Zugangspunkt TP-Link
- Zugangspunkt Black Box
- Zugangspunkt Techly
- Zugangspunkt Hercules
- Zugangspunkt Huawei
- Zugangspunkt Edimax
- Zugangspunkt DrayTek
- Zugangspunkt Totolink
- Zugangspunkt D-Link
- Zugangspunkt Digitus
- Zugangspunkt DataVideo
- Zugangspunkt Lancom
- Zugangspunkt LevelOne
- Zugangspunkt Cisco
- Zugangspunkt Grandstream
- Zugangspunkt Tenda
- Zugangspunkt Ubiquiti Networks
- Zugangspunkt Intellinet
- Zugangspunkt Bintec-elmeg
- Zugangspunkt Planet
- Zugangspunkt EnGenius
- Zugangspunkt Mikrotik
- Zugangspunkt Moog
- Zugangspunkt Homematic IP
- Zugangspunkt EQ3
- Zugangspunkt Comtrend
- Zugangspunkt INCA
- Zugangspunkt Media-tech
- Zugangspunkt Mercku
- Zugangspunkt Mojo
- Zugangspunkt Sitecom
- Zugangspunkt SMC
- Zugangspunkt Steren
- Zugangspunkt AMX
- Zugangspunkt Vimar
- Zugangspunkt Cudy
- Zugangspunkt Moxa
- Zugangspunkt StarTech.com
- Zugangspunkt AirLive
- Zugangspunkt Kingston
- Zugangspunkt LigoWave
- Zugangspunkt Dahua Technology
- Zugangspunkt Speco Technologies
- Zugangspunkt Atlantis Land
- Zugangspunkt Cradlepoint
- Zugangspunkt SilverNet
- Zugangspunkt Advantech
- Zugangspunkt Juniper
- Zugangspunkt Insteon
- Zugangspunkt Crestron
- Zugangspunkt 3Com
- Zugangspunkt WatchGuard
- Zugangspunkt Aerohive
- Zugangspunkt V7
- Zugangspunkt Syscom
- Zugangspunkt Silex
- Zugangspunkt NUVO
- Zugangspunkt Mach Power
- Zugangspunkt IP-COM
- Zugangspunkt ICC
- Zugangspunkt Amer
- Zugangspunkt Allied Telesis
- Zugangspunkt Hawking Technologies
- Zugangspunkt Cambium Networks
- Zugangspunkt Brocade
- Zugangspunkt Extreme Networks
- Zugangspunkt Bountiful
- Zugangspunkt Meru
- Zugangspunkt Amped Wireless
- Zugangspunkt Ruckus Wireless
- Zugangspunkt Premiertek
- Zugangspunkt FlyingVoice
- Zugangspunkt Luxul
Neueste Bedienungsanleitung fĂĽr -Kategorien-
13 Oktober 2024
11 Oktober 2024
8 Oktober 2024
4 Oktober 2024
4 Oktober 2024
1 Oktober 2024
1 Oktober 2024
29 September 2024
28 September 2024
24 September 2024