Fortin EVO-ONE Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Fortin EVO-ONE (18 Seiten) in der Kategorie Fernbedienung. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/18
ALL-IN-ONE DATA INTERFACE
REMOTE STARTER / ALARM
QUICK
INSTALLATION GUIDE
D C B HIJ
(6-PIN) BYPASS RELAY
(5-PIN) CAN-BUS (4-PIN) RS-232 DATA-LINK & FLASH-LINK UPDATER PORT
BYPASS PROGRAMMING BUTTON
REMOTE STARTER PROGRAMMING LED
CUT LOOP FOR
AUTOMATIC
TRANSMISSION
MODE.
Red White Blue Blue Black
LED Blue CAN ACTIVITY
LED Yellow IGNITION ON
LED Red BYPASS DATA
E6
A
F
G
E
(+) Foot Brake Black In
750mA (-) Parking lights Pink Out
750mA (-) Trunk Release / AUX Yellow/Black Out
(-) Hand Brake Brown/White In
(-) Hood/Door Pink/Black In
%\SDVVFRQ¿J Purple/Yellow
%\SDVVFRQ¿J Green/White
%\SDVVFRQ¿J Green/Red
%\SDVVFRQ¿J White/Black Out
%\SDVVFRQ¿J /W%OXH
Ground Black In
(+) Ignition Pink Out
(+) Starter Yellow Out
Out White
(+) ParkLight/IGN2
/ACC/START
3URJUDPPDEOH2XWSXW
(FUNCTION 2 & 31)
Out 2UDQJH
(+) ACC / IGN2
3URJUDPPDEOH2XWSXW
(FUNCTION 2 & 31)
In Red (+) 12V
In Yellow (+) Bypass Ignition
Out Purple (-) Lock 750mA
Out Purple/White (-) Unlock 750mA
Out Green (-) Ignition 750mA
Out White (-) Start 750mA
Out 2UDQJH (-) Disarm 750mA
Out 2UDQJH%ODFN (-) Horn/Siren 2 Amp
Out 'N%OXH (-) GWR / Programmable 750mA
In Red/Blue %\SDVVFRQ¿J
/W%OXH%ODFN %\SDVVFRQ¿J
750 mA MAXIMUM OUTPUT. Do not exceed the maximum current or permanent damage to the module
will occur that will not be covered under warranty.
(6-PIN) POWER CONNECTOR
(20-PIN) SECONDARY CONNECTOR
COPYRIGHT © 2014-2017, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED MADE IN CANADA REV.:20170323
A1
E1
(3-PIN) Shock Sensor
(2-PIN) Valet/Programming Button
A20
WIRING / CONNECTION GUIDE
PROGRAMMING REMOTE TRANSMITTER(S)
Black
White
White
White
(4-PIN) ANTENNA(4-PIN) DATA-LINK ANTENNA
REMOTE
STARTER
FIRMWARE
VERSION
1. [21]
ET PLUS
The system can learn up to a maxi-
mum of 4 transmitters.
Any transmitters can be stored in
more than 1 memory slot.
When a 5th transmitter is learned
the 1st remote is erased (FIFO).
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6
WITH IGNITION SWITCH
Turn the Ignition
OFF.
Turn the
Ignition ON.
F
M
H
2
-
W
The LED will
turn ON
x4
Press and
release the
brake pedal
four times.
F
MH
2
-
W
Turn the
Ignition
ON.
WITH VALET SWITCH
Press and hold
the valet switch
until the park-
ing lights turn
ON, the horn/
siren will chirp. x5
Press and release the valet switch
ve time.
The parking lights will ash and the
horn/siren will chirp each time to
conrm. x1
Press and re-
lease the brake
pedal once.
The LED
will ash
rapidly.
On each Transmitter press
and release the button
then press and release the
button. The LED will stop
ashing conrming programming.
Turn the Ignition
OFF to exit
programming.
1 32 4
EVO-ONEEVO-ONE
DOWNLOAD THE SPECIFIC VEHICLE INSTALLATION
GUIDE GUIDE, USER OR THE LATEST QUICK
INSTALLATION GUIDE AT:
WWW.FORTIN.CA
RF642W
GUIDE # 33021
FUNCTION
FUNCTION MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6
1 — — — — — — —
2
Programmable Output
(+) Ign/Acc/Start
(FUNCTION 31
MODE 4)
White (+)Ignition2 White (+)Accessory2 White (+)Start2 White (+)Start
— —
Orange (+)Accessory Orange (+)Accessory Orange (+)Accessory Orange (+)Ignition2
Pink (+)Ignition Pink (+)Ignition Pink (+)Ignition Pink (+)Ignition
Yellow (+)Start Yellow (+)Start Yellow (+)Start Yellow (+)Start2
3 Tachless sensivity Increase
crank time (By default)
Decrease
crank
time
4Remote car starter
runtime
Gas: 15 minutes
Diesel: 30 minutes
Gas: 7 minutes
Diesel: 14 minutes
Gas: 3 minutes
Diesel: 6 minutes — — —
5Add Remote on FMH
antenna series Add Remote — — — — —
6 Doorlock option No Unlock before remote-start &
Lock after remote-start. Lock after remote-start. Unlock and relock after
shut-down.
Relock 10 sec.after
shut-down.
Disarm before
shut down.
7Ignition Doorlock
option No
Lock after foot-brake &
unlock after key is turned
OFF.
Unlock after key is turned
OFF.
Doorlock Output at
Ignition only. — —
8 Unlock Pulse Time Single 0.25 sec Double 0.25 sec Single 4.0 sec Single 2.5 sec Single 1.5 sec Single 0.75 sec
9Active or Passive
Alarm & Starter Kill.
Active
Press LOCK to activate
the Alarm and starter-kill.
Passive (Lock disabled)
Arm alarm activate
starter-kill 30(MODE
4), 60(MODE5), or
120(MODE6) sec. after the
door is closed.
Passive (Lock enabled)
Arm alarm, activate
starter-kill and lock doors
30(MODE 4), 60(MODE5),
or 120(MODE6) sec. after
the door is closed.
Passive arm
30 seconds (by default
if MODE 2 ot 3 is
activated.
Passive arm
60 seconds. (if
MODE 2 ot 3 is
activated.
Passive arm
120 seconds.
(if MODE 2 ot 3
is activated.
10
Starter Kill Output.
Required function 32
mode 4. - Dk.Blue
(A8) = starter-kill.
Starter-kill &anti-grind Anti-grind only Relay normally open — — —
11
Sound Con rmation
& LED antenna
Antidémarreur
1st LOCK/UNLOCK silent
2nd LOCK/UNLOCK
sound
---------------------------
Antenna LED active.
LOCK/UNLOCK
sound always. Antenna LED disabled. Antenna LED disabled
with ignition.
Con rmation sound
at LOCK only
Panic mode
disabled
12 Output horn/siren
con guration Horn(-) only. Siren(+) Output (E1) white Siren(+) Output (E1) white
and Horn(-) Siren(-) only (A7) — —
13 Con rmation Pulse Long Short — — — —
14 Alarm ON/OFF
Starter ON/OFF
Alarm OFF
Remote-starter ON
Alarm ON
Remote-starter ON.
Alarm ON
Remote-starter OFF — — —
15
Smart Arming
Smart Doorlock
Smart Lock pulse
Disable
(Unlock signal) Automatically
LOCK and rearm alarm if
door(s) are not opened after
30 seconds.
Automatic Lock when
starter kill arms.
Lock pulse only when its
Unlock — —
16 Cold Start Timer 3 hours at -5 oc/Runtime 1.5 hours at -5oc/Runtime 3 hours at -5oc/5 minutes 1.5 hours at -5oc/5
minutes Cold time OFF —
17 — — — — — — —
18 Diesel Mode Disable
Enable (20 seconds)
Delay between Ignition
power up and Starter (crank).
Enable (10 seconds)
Delay between Ignition
power up and Starter
(crank).
Enable
No delay between
Ignition power up and
Starter (crank).
— —
19 Turbo timer Disable Run 2 minutes. Run 4 minutes. — — —
20
Engine supervision:
-Tachless -
-analog tach-
-Tach Data-Link-
Tachless on crank
and supervision Tach
Data-Link.
Tachless only.
( vehicles with automatic
transmission only)
—
Start (crank) 8 seconds
on Tachless.
( vehicles with
automatic transmission
only)
Start (Crank) 8 sec
+ Supervision by
Data-LInk Tach
Tach Data-Link
only
STEP STEP STEP STEP STEP STEP 1 2 3 4 5 6
Disarm
the
system
(The
antenna
led must
not be
 ashing,
see enter/
exit valet
mode
p.4).
OR
FM H
2
-
W
OR
FMH
2-W
X1
MODE 1 - LOCK
MODE 2 - UNLOCK
MODE 3 - START (3 SECONDS)
MODE 4 - FUNCTION (3 SECONDS)
MODE 5 - FUNCTION LOCK
MODE 6 - FUNCTION UNLOCK
Turn the
Ignition
ON.
Press and
hold the valet
switch or the
antenna but-
ton until the
Parking lights
turn ON, the
horn/siren will
chirp.
The
LED will
 a s h
rapidly.
Press and release the valet
switch or the antenna but-
ton X time for the desired
function. The Parking
lights will  ash and the
horn/siren will chirp each
time to con rm.
Press and
release the
brake-ped-
al once.
Turn the Igni-
tion OFF to
exit program-
ming.
The Parking
lights will
 ash 4
times.
Press the BUTTON on a programmed remote to select the mode (X).
The Parking lights will  ash 1-6 times to con rm.
Return to step 3 to programmed the next option
FMH
2-W
FUNCTION PROGRAMMING
FUNCTION MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6
21 Start Attempts 2 1 3 — — —
22 — — — — — — —
23 Master RESET
RESET all programming
options by default.
(Retains already
programmed remote.)
— — — — —
24 — — — — — — —
25 Yellow/Black (A13) :
Aux1 --> LOCK
0.5 seconds &
disarm alarm 0.5 seconds 10 sec latch or
until a button is pressed.
20 sec latch or
until a button is pressed.
30 sec latch or
until a button is
pressed.
Latch until
shutdown
26 Hybrid mode Gas / Diesel vehicle Hybrid vehicle — — — —
27 — — — — — — —
28 — — — — — — —
29 Alarm Duration 30 seconds 60 seconds 120 seconds — — —
30 Valet code Ignition ON
Valet button p3-x3 times.
Ignition ON
Valet button p3-x3 times
and p3-x1 times 3 seconds.
Ignition ON
Valet button p3-x4 times
and p3-x1 times 3 seconds.
Ignition ON
Valet button p3-x5 times
and p3-x1 times 3 seconds.
Ignition ON
Valet button p3-x6
times and p3-x1 times
3 seconds.
Ignition ON
Valet button p3-x7
times and p3-x1
times 3 sec.
31
Special application
Programmable output
(+)
No special application
Priority on function 2
Special application - Function 2 (all option)
not available.
White (+) Parking
Light White
(+)
Parking
Light
White:
(+) Parking
Lights
Orange (+)
Accessory Orange Ign.2
Orange:
(+) Parking
lights
White wire (E1) : Enable
at ground out, disable with
vehicle ignition OFF.
White wire (E1) : Trunk
Output Pink (+) Ignition Pink Ign.1 Pink:
(+) Ignition
Yellow (+) Start Yellow (+) Start Yellow:
(+) Start
32 Ground Out
Dk.Blue (Ground out):
Shut-down 1 second after
remote start run time.
Dk.Blue (Ground out):
Shut-down 3 seconds after
remote start run time.
Dk.Blue
(Ground Out):
Shutdown After
D.k Blue
(Ground Out):
Starter-Kill
D.k Blue
(Ground Out):
Arm / Rearm
Controlled by
CAN learning
33 Manual transmission
function
Manual transmission
completed by door closed.
Automatically activated by
hand-brake and Foot Brake
Manual sequence
completed by locking the
doors
Cancel ready mode when
trunk open. — —
34 Trunk output Pulse 0.5 seconds Pulse 2.5 seconds Unlock before trunk pulse
0.5sec
Trunk Output at ignition
only — —
35 Door unlock Special
application No special application Activate vehicle ignition at
unlock.
Activate vehicle ignition
and accessory at unlock. — — —
36
Activation/
desactivation remote
Valet Mode
—
by remote :
FUNCTION --> LOCK +
UNLOCK or valet button
By Valet button only — — —
37
Security Remote car
starter
Special application
No special application
Security ON: Shutdown
Engine if the door is opened
before UNLOCK is pressed.
(Door trigger required).
— — — —
38 System control by
OEM Remote Disable Press 3x Lock to remote start Start/Stop on trigger shock
sensor
Alarm control by OEM
Remote.
Press Lock, Unlock
Lock to remote start —
39 Temperature option Disable
Enable : AUX1 activated at
5
oc when remote started (see
function 25)
— — — —
LEGEND: FUNCTION BY DEFAULT
FUNCTION
RESETS ALL FUNCTIONS BACK TO DEFAULT AND ERASES ANY REMOTES THAT HAVE BEEN PROGRAMMED.
Disarm the
system (The
antenna led
must not be
ashing, see
enter/exit
valet mode
p.4).
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6
Turn the
Ignition
ON.
OR
Press and hold the
valet switch or the
antenna button until
the Parking lights
turn ON, the horn/
siren will chirp.
OR
Press and
release the
valet switch
or the antenna
button
23 times.
X1 Press and
release
the brake-
pedal
once.
OR Press and hold
the valet switch
or the antenna
button for 5 sec-
onds. The Parking
lights will ash to
conrm.
Turn the Igni-
tion OFF to
exit program-
ming. The
Parking lights
will ash 4
times.
FM H
2-W
FM H
2-W
FM H
2-W


Produktspezifikationen

Marke: Fortin
Kategorie: Fernbedienung
Modell: EVO-ONE

Brauchst du Hilfe?

Wenn Sie Hilfe mit Fortin EVO-ONE benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Fernbedienung Fortin

Bedienungsanleitung Fernbedienung

Neueste Bedienungsanleitung für -Kategorien-