Fluke 700PTP-1 Bedienungsanleitung

Fluke Nicht kategorisiert 700PTP-1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Fluke 700PTP-1 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

PN 2811824

April 2007

All product names are trademarks of their respective companies.

Pump Valve Assembly Cleaning Instructions

Occasionally, the 700PTP-1 may not work properly due to contamination of

the internal valve assembly. Use the following procedure to clean the valve

assembly. If the procedure does not fix the problem, a repair kit (part

number 2812587) may be ordered.

1. Using a small screwdriver, remove the 2 valve retention caps located

on opposite sides of the pump below the pressure/vacuum switch.

2. Gently remove the spring and o-ring assembly. Take care when

removing check valve as it contains several small components. See

Figure 3.

euz03f.eps

Figure 3. Cleaning t

Figure 3. Cleaning tFigure 3. Cleaning the Valve Assemb

he Valve Assemb

he Valve Assembhe Valve Assembly

ly ly

3. Set aside the valve assemblies and clean out the valve body using a

cotton swab soaked in isopropyl alcohol.

4. Repeat the process several times using a new swab until clean.

5. Operate the pump handles several times and recheck for

contamination.

6. Clean the o-ring assembly and the o-ring on the retention caps with

isopropyl alcohol and inspect the o-rings closely for any damage or

excessive wear. Replacements are included in the repair kit.

7. Inspect the springs for wear or loss of tension. They should be

approximately 8.6 mm long in the relaxed state. If shorter, they may

provide sufficient sealing tension. Replace if needed.

8. Once all parts have been cleaned and inspected, reinstall the o-ring

and spring assembly into the valve body.

9. Reinstall the retention caps and gently tighten each cap.

10. Seal the output port and operate the pump to at least 50 % of capacity.

11. Release the pressure and repeat several times to ensure that the

o-rings seat properly.

Replacement Parts

Hose assembly, Fluke PN 2815714

Rebuild kit, Fluke PN 2812587

Bleed Valve Assembly (Needle) Fluke PN 2844329

LIMITED WARRANTY AND LIMITATION O

LIMITED WARRANTY AND LIMITATION OLIMITED WARRANTY AND LIMITATION OF LIABILITY

F LIABILITY

F LIABILITY F LIABILITY

This Fluke product will be free from defects in material and workmanship for one year

from the date of purchase. This warranty does not cover fuses, disposable batteries,

or damage from accident, neglect, misuse, alteration, contamination, or abnormal

conditions of operation or handling. Resellers are not authorized to extend any other

warranty on Fluke’s behalf. To obtain service during the warranty period, contact your

nearest Fluke authorized service center to obtain return authorization information,

then send the product to that Service Center with a description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS

FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS

NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some

states or countries do not allow the exclusion or limitation of an implied warranty or

of incidental or consequential damages, this limitation of liability may not apply to

you.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

11/99

Introduction

The Fluke-700PTP-1 Pneumatic Test Pump (hereafter called the “pump”) is

a handheld device that develops precise pressure and vacuum. The pump

has the following specifications:

• Pressure to 40 bar (600 psi)

• Vacuum to -0.96 bar (-13.9 psi)

• Wetted materials: aluminum, silicon, neoprene, stainless steel,

Buna-N

• Weight: 1.03 lb (467 g)

• Dimensions: length 8.7 in (220 mm), width 4.8 in (122 mm), depth

3.5 in (89 mm)

Box Contents

• 700PTP-1 Pneumatic Test Pump

• 1/4 in NPT male to 1/4 in BSP female

• 1 m hose

• (2) 1/8 in NPT male quick connects

• 1/8 NPT female to 1/4 in BSP female

• Seal Kit

• Instruction Sheet

Contacting Fluke

To contact Fluke or for service, call one of the following telephone numbers:

USA: 1-888-44-FLUKE (1-888-443-5853)

Canada: 1-800-36-FLUKE (1-800-363-5853)

Europe: +31 402-675-200

Japan: +81-3-3434-0181

Singapore: +65-738-5655

Anywhere in the world: +1-425-446-5500

Or, visit Fluke's Web site at www.fluke.com .

Fluke-700PTP-1

Pneumatic Test Pump

Instruction Sheet

Features

euz01f.eps

No. Item

No. Item No. Item Function

Function

Function Function

A Master

instrument port Port for Fluke 700 Series Pressure Module

B Pressure /

vacuum button

Push in from this side for vacuum, and from

the other side for pressure. Use a small

screwdriver.

C Test pressure

port hose

Flexible hose to pressure instrument under

test

D Quick

Connects 1/8 in NPT male

E Maximum

stroke limiter

To limit the pressure from the hand pump,

tighten these nuts to shorten the compression

stroke.

F Pressure

release valve

Unscrew to vent pressure from the pump.

Tighten the valve to close the valve before

applying pressure.

Fine

adjustment

knob

To precisely adjust the applied pressure

H Adapter 1/8 in NPT female to 1/4 in BSP female

I (2) Clean out

ports

See “Pump Valve Assembly Cleaning

Instructions”

Figure 1. Featu

Figure 1. FeatuFigure 1. Features

res

res res

Using the Pump

T C

mA m A

RT D

SOURCE

300V

MAX30V

MAX

30V

MAX

30V

MAX

MEAS

CAT

743

DOCUME NTING PROCESS CALI BRA TOR

MEAS

SOU RCE

SET UPmA

RTD

789

456

123

S I G N A L

T E S T

+ –

Red

Black

ENTER

CLEAR

(Z ERO)

RANGE

Pressure

Module

Test Pump

UUT

Calibrator

euz02c.eps

Figure 2. U

Figure 2. UFigure 2. Using the Pu

sing the Pu

sing the Pusing the Pump

mp mp

WWarning

To avoid a violent release of pressure, always

depressurize the system slowly using the pressure

release valve (item F

FF) before detaching any

pressure line from the pump. Do not connect the

pump to an external pressure source.

1. Attach a 700 Series Pressure Module (hereafter called “pressure

module”) to the master instrument port. Use Teflon tape or other

sealing medium on all NPT thread connections to eliminate leakage.

2. Connect the test pressure port hose (item ) to the pressure input of C

the pressure instrument under test.

3. Make sure the pressure/vacuum button (item B) is in the desired

position.

4. Unscrew the pressure release valve (item F) to vent pressure from

the pump.

5. Zero the pressure module. The zeroing procedure depends on which

pressure module and calibrator is in use.

6. Turn the fine adjustment knob (item G) to mid-range.

7. Tighten the pressure release valve (item F). Do not over tighten.

8. To limit the maximum pressure that can be developed by the pump,

tighten the maximum-stroke limiting adjustment nuts (item E). This

also reduces the amount of pressure increase per stroke.

9. To apply very low pressures, use the fine adjustment knob only (item

G).

10. Squeeze the handles together to apply incrementally higher pressure.

For pressure over 7 bar (100 psi), use two hands.

11. Adjust the pressure using the fine adjustment knob (item G).

Produktspezifikationen

Marke:	Fluke
Kategorie:	Nicht kategorisiert
Modell:	700PTP-1
Breite:	122 mm
Tiefe:	220 mm
Gewicht:	467 g
Produkttyp:	Pneumatische Prüfpumpe
Höhe:	89 mm
Material:	Aluminium, Neoprene, Silicone, Stainless steel
Maximaler Betriebsdruck:	40 bar
Betriebsanleitung:	Ja
Markenkompatibilität:	Fluke
Schlauch enthalten:	Ja
Luftdruck (max.):	- bar
Dichtungen enthalten:	Ja