Fluke 2000ACC Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Fluke 2000ACC (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
2000ACC
Accessory Kit
Instructions
Contact Fluke
Fluke Corporation operates worldwide. For local contact
information, go to our website: www.fluke.com.
To register your product, or to view, print, or download the
latest manual or manual supplement, go to our website:
www.fluke.com/productinfo.
+1-425-446-5500 fluke-info@fluke.com
Safety Information
A Warning identifies hazardous conditions and procedures
that are dangerous to the user. A Caution identifies
conditions and procedures that can cause damage to the
Product or the equipment under test.
 Warning
To prevent possible electrical shock, fire, or
personal injury:
Read all safety information before you use the
Product.
Use the Product only as specified, or the protection
supplied by the Product can be compromised.
Carefully read all instructions.
Fluke Corporation
P.O. Box 9090
Everett WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
PN 5416998 (English)
1/2023
©2023 Fluke Corporation. All rights reserved. Specifications are
subject to change without notice. All Product names are
trademarks of their respective companies.
2
Comply with local and national safety codes. Use
personal protective equipment (approved rubber
gloves, face protection, and flame-resistant
clothes) to prevent shock and arc blast injury where
hazardous live conductors are exposed.
Use Product-approved measurement category
(CAT), voltage, and amperage rated accessories
(probes, test leads, and adapters) for all
measurements.
Do not touch voltages >30 V ac rms, 42 V ac peak,
or 60 V dc.
Do not use the Product around explosive gas,
vapor, or in damp or wet environments.
Do not exceed the Measurement Category (CAT)
rating of the lowest rated individual component of a
Product, probe, or accessory.
Do not use test leads if they are damaged. Examine
the test leads for damaged insulation, exposed
metal, or if the wear indicator (if present) shows.
Check test lead continuity.
Keep fingers behind the finger guards on the
probes.
Do not use in CAT III or CAT IV environments
without the protective cap (if included with the
Product) installed on test probe. The protective cap
decreases the exposed probe metal to <4 mm. This
decreases the possibility of arc flash from short
circuits.
Do not use a shrouded banana jack accessory such
as an alligator clip with an unshrouded 4 mm
banana probe tip terminal in a hazardous electrical
installation. Due to the lack of a shroud, the probe
tip connector does not provide suitable insulation
to accessible parts with this type of assembly.
3
Symbols
The table below lists the symbols that can be used on the
Product or in this document.
Maintenance
Clean with a soft towel moistened with water and mild
detergent. DO NOT IMMERSE in liquid.
Electrical Specifications
Refer to markings on probe assembly and accessories for
voltage and current specifications. If no CAT rating is
marked, by default ratings are 30 V ac rms, 42 V ac peak or
60 V dc, 8 A. Probe tips with >19 mm (0.75 in) exposed metal
are rated 30 V ac, 60 V dc, 8 A.
Environmental Specifications
Symbol Description
Consult user documentation.
WARNING. RISK OF DANGER.
WARNING. HAZARDOUS VOLTAGE. Risk of
electric shock.
Double insulated
Measurement Category II is applicable to test
and measuring circuits connected directly to
utilization points (socket outlets and similar
points) of the low-voltage MAINS installation.
Measurement Category III is applicable to test
and measuring circuits connected to the
distribution part of the building’s low-voltage
MAINS installation.
Measurement Category IV is applicable to test
and measuring circuits connected at the
source of the building’s low-voltage MAINS
installation.
Conforms to European Union directives.
Temperature -20 °C to 50 °C (-4 °F to 122 °F)
Relative humidity 0 % to 95 %, 0 °C to 35 °C
(32 °F to 95 °F)
Altitude 2000 m
Safety IEC 61010-031: Pollution Degree 2


Produktspezifikationen

Marke: Fluke
Kategorie: Nicht kategorisiert
Modell: 2000ACC

Brauchst du Hilfe?

Wenn Sie Hilfe mit Fluke 2000ACC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Fluke

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-