Festo HMVM-LP-DL25/40 Bedienungsanleitung

Festo Nicht kategorisiert HMVM-LP-DL25/40

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Festo HMVM-LP-DL25/40 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
1. Grundbausatz mit Montagebeispiel
1.a. HMVM-LP-DL25/40
1 Grundbausatz
HMVM-LP-DL25/40
inklusive Befestigungs-
elemente A-D (siehe Ta-
belle).
1.b. Montagebeispiel
2 Antriebseinheit
(siehe Tabelle)
3 Anbaukomponente
(siehe Tabelle)
Bestimmungsgemäß dient
der Grundbausatz 1 als
Basis zum Aufbau von Li-
nienportalsystemen in Mono-
Bauweise (Y-Module).
Hinweis
• Befestigen Sie einen Grundbausatz mindestens alle 500 mm.
• Berechnen Sie die dazu benötigte Anzahl y nach folgenden Formeln:
- bei Hub ≤ 500 mm: y = 2
- bei Hub > 500 mm : y = Ganzzahl (Hub/500) +2
Hinweis
• Montieren Sie die Antriebe bzw. das Wegmesssystem immer zuerst an
den Grundbausatz.
2. Befestigungsschnittstellen an Antriebseinheiten
2.a. Adaption an Linearantrieb DG..-25-..-KF
1 Grundbausatz
HMVM-LP-DL25/40
2 Linearantrieb
DGPL-25-KF,
DGE-25-SP-KF oder
DGE-25-ZR-KF
2.b. Adaption an Linearantrieb DGC-25-KF
1 Grundbausatz
HMVM-LP-DL25/40
2 Linearantrieb
DGC-25-KF
2.c. Adaption an Linearantrieb DGE-25-ZR-RF
1 Grundbausatz
HMVM-LP-DL25/40
2 Linearantrieb
DGE-25-ZR-RF
2.d. Adaption an Linearantrieb DGE-40-ZR-RF oder DG..-40-..-KF
1 Grundbausatz
HMVM-LP-DL25/40
2 Linearantrieb
DGE-40-ZR-RF,
DGPL-40-KF,
DGE-40-ZR-KF oder
DGE-40-SP-KF
2.e. Adaption an Linearantrieb DGC-40-KF
1 Grundbausatz
HMVM-LP-DL25/40
2 Linearantrieb
DGC-40-KF
3. Befestigungsschnittstellen an Wegmesssystem
3.a. Adaption an Wegmesssystem MLO-POT-TLF
1 Grundbausatz
HMVM-LP-DL25/40
2 Antriebseinheit
3 Wegmesssystem
MLO-POT-TLF
4. Befestigungsschnittstellen an Anbaukomponenten
4.a. Adaption an ein Profilsystem mit 40 mm Nutenabstand
1 Grundbausatz
HMVM-LP-DL25/40
3 Profil
HMBS-80x80
4.b. Adaption an das Auflageprofil HMIA-E05
Alternative 1 Alternative 2
1 Grundbausatz
HMVM-LP-DL25/40
3 Auflageprofil
HMIA-E05
•Lesen Sie dazu die Monta-
geanleitung des Auflage-
profils HMIA-E0... .
Hinweis
• Beachten Sie:
- dass nur Befestigungskombinationen aus der Tabelle zulässig sind.
- dass Befestigungselemente bei manchen Kombinationen übrig bleiben.
- dass die Stückzahlen in der Tabelle pro Grundbausatz angegeben sind.
- zur Erdung, die Montageanleitung des Erdungsbausatzes.
Montageanleitung (de)
688602 / 2005-02NH
†‡
Grundbausatz
HMVM-LP-DL25/40
Festo SE & G Co. K
Postfach
73726 Esslingen
++49/(0)711/347-0
www.festo.com
1
1
1
11 Grundbausatz
Typ
Teile-Nr.
2
2
2
22 Antriebseinheit
Typ DG..-25-..-KF DGC-25-KF DGE-25-ZR-RF DG..-40-..-KF DGC-40-KF DGE-40-ZR-RF
3
3
3
33 Anbaukomponenten Wegmesssys.
Typ MLO-POT-TLF HMBS-80x80 HMIA-E05
Schnittstelle 2.a. 2.b. 2.c. 2.d. 2.e. 2.d. 3.a. 4.a. 4.b.
Zylinderschrauben
M5x10 DIN 912 2x
M5x12 DIN 912 4x 4x
M5x14 DIN 912 3x 2)
M5x25 DIN 912 4x 4x 2x
M6x12 DIN 912 2x
Senkschrauben
M5x14 DIN 7991 3x 2)
Zylinderstifte
5m6x16 DIN 7 2x
6m6x16 DIN 7 2x
6m6x24 DIN 7 1x 1x
Nutensteine
HMBN-5-M5 4x 4x 3x
Zylinderschrauben
M5x20 DIN 912 8x (16x) 1)
Nutensteine
HMBN-8-2M5 4x (8x) 1)
Mittenstützen
MUP-18/25 2x 2x
MUC-25 1x
MUC-40 1x
Verbindungsplatten
HMVO-RF25 2x
HMVO-POT 1x 3)
M5 M6
5,8 10
1) Die Klammerwerte beziehen sich auf doppelte Profilanbindung.
2) Je nach Befestigungsanforderung werden entweder Zylinderschrauben A oder Senkschrauben B benötigt.
3) Die Verbindungsplatte als Höhenausgleich ist nur bei Größe 25 erforderlich.
HMVM-LP-DL25/40
Anzugsdrehmoment in Nm
539 972
D
A
B
Befestigungselemente im Lieferumfang
Linearantriebe ..-40-..Linearantriebe ..-25-..
E
C
Befestigungselemente nicht im Lieferumfang
Gewinde
H
G
F
1
2
1
1
3
1
A
G
C
G
A
2
1
A
G
H
2
1
D
C
A
A
1
2
C
G
3
H
A
2
3
1
E
F
A
B
D
D
2
1
2
1
3
1
3
1
1. Basic kit with assembly example
1.a. HMVM-LP-DL25/40
1 Basic kit
HMVM-LP-DL25/40
Including mounting at-
tachments (A-D) (see
table).
1.b. Assembly example
2 Drive unit
(see table)
3 Attachment component
(see table)
The basic kit 1 is intended
for use as a basis for the set
up of linear gantry systems in
mono design (Y modules).
Note
• Attach a basic kit at least every 500 mm.
• Calculate the required quantity y using the following formulas:
- Where stroke length = 500 mm: y = 2
- Where stroke length > 500 mm: y = whole-number (stroke/500) +2
Note
• Always mount the drives or the displacement system to the basic kit
first.
2. Mounting interfaces to drive units
2.a. Adaptation to linear drive DG..-25-..-KF
1 Basic kit
HMVM-LP-DL25/40
2 Linear drive
DGPL-25-KF,
DGE-25-SP-KF oder
DGE-25-ZR-KF
2.b. Adaptation to linear drive DGC-25-KF
1 Basic kit
HMVM-LP-DL25/40
2 Linear drive
DGC-25-KF
2.c. Adaptation to linear drive DGE-25-ZR-RF
1 Basic kit
HMVM-LP-DL25/40
2 Linear drive
DGE-25-ZR-RF
2.d. Adaptation to linear drive DGE-40-ZR-RF or DG..-40-..-KF
1 Basic kit
HMVM-LP-DL25/40
2 Linear drive
DGE-40-ZR-RF,
DGPL-40-KF,
DGE-40-ZR-KF or
DGE-40-SP-KF
2.e. Adaptation to linear drive DGC-40-KF
1 Basic kit
HMVM-LP-DL25/40
2 Linear drive
DGC-40-KF
3. Mounting interfaces to displacement encoders
3.a. Adaptation to displacement encoder MLO-POT-TLF
1 Basic kit
HMVM-LP-DL25/40
2 Drive unit
3 Displacement encoder
MLO-POT-TLF
4. Mounting interfaces to attachment components
4.a. Adaptation to a profile system with 40 mm slot width
1 Basic kit
HMVM-LP-DL25/40
3 Profile
HMBS-80x80
4.b. Adaptation to support profile HMIA-E05
Alternative 1 Alternative 2
1 Basic kit
HMVM-LP-DL25/40
3 Support profile
HMIA-E05
•Refer to the assembly
instructions for support
profile HMIA-E0... to this
end.
Note
• Please note:
- that only attachment combinations shown in the table are permissible.
- that mounting attachments are left over with some combinations.
- that the quantities in the table are specified per basic kit.
- for earthing, the assembly instructions for the earthing kit.
Assembly instructions (en)
688602 / 2005-02NH
†‡
Basic kit
HMVM-LP-DL25/40
Festo SE & G Co. K
Postfach
73726 Esslingen
++49/(0)711/347-0
www.festo.com
1
1
1
11 Basic kit
Type
Part No.
2
2
2
22 Drive unit
Type DG..-25-..-KF DGC-25-KF DGE-25-ZR-RF DG..-40-..-KF DGC-40-KF DGE-40-ZR-RF
3
3
3
33 Attachment comp. Displacement
Type MLO-POT-TLF HMBS-80x80 HMIA-E05
Interface 2.a. 2.b. 2.c. 2.d. 2.e. 2.d. 3.a. 4.a. 4.b.
Socket head screws
M5x10 DIN 912 2x
M5x12 DIN 912 4x 4x
M5x14 DIN 912 3x 2)
M5x25 DIN 912 4x 4x 2x
M6x12 DIN 912 2x
Countersunk screws
M5x14 DIN 7991 3x 2)
Dowel pins
5m6x16 DIN 7 2x
6m6x16 DIN 7 2x
6m6x24 DIN 7 1x 1x
Slot nuts
HMBN-5-M5 4x 4x 3x
Socket head screws
M5x20 DIN 912 8x (16x) 1)
Slot nuts
HMBN-8-2M5 4x (8x) 1)
Central supports
MUP-18/25 2x 2x
MUC-25 1x
MUC-40 1x
Connecting plates
HMVO-RF25 2x
HMVO-POT 1x 3)
M5 M6
5.8 10
1) Values in parentheses make reference to a double profile connection.
2) Either socket head screws A or countersunk screws B are required, depending upon attachment requirements.
3) The connecting plate is only required for height compensation for size 25.
HMVM-LP-DL25/40
Tightening torque in Nm
539 972
D
A
B
Mounting attachments included in scope of delivery
Linear drives ..-40-..Linear drives ..-25-..
E
C
Mounting attachments not included in scope of delivery
Thread
H
G
F
1
2
1
1
3
1
A
G
C
G
A
2
1
A
G
H
2
1
D
C
A
A
1
2
C
G
3
H
A
2
3
1
E
F
A
B
D
D
2
1
2
1
3
1
3
1


Produktspezifikationen

Marke: Festo
Kategorie: Nicht kategorisiert
Modell: HMVM-LP-DL25/40

Brauchst du Hilfe?

Wenn Sie Hilfe mit Festo HMVM-LP-DL25/40 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Festo

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-