Festo HMIXB-RP/FP-2 Bedienungsanleitung

Festo Nicht kategorisiert HMIXB-RP/FP-2

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Festo HMIXB-RP/FP-2 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Montageanleitung (de)
744 386 / 2009-09NH
†‡
Installationsbausatz
HMIXB-RP/FP-2
Festo SE & Co. KG
Postfach
D-73726 Esslingen
++49/(0)711/347-0
www.festo.com
1. Installationsbausatz
1a. HMIXB-RP/FP-2
13916d_2
1 Installationsbausatz
HMIXB-RP/FP-2
1b. Montagebeispiel
13916d_1..Raumportal
2 Antriebseinheit
(! Tabelle)
3 Anbaukomponente
(! Tabelle)
Bestimmungsgemäß dient der Installationsbausatz HMIXB-RP/FP-2 1 als
Basis zum Aufbau von Raumportalsystemen in Duo-Bauweise (X-Module).
Vorsicht
Verletzungsgefahr durch elektrische Spannung.
•Verbinden Sie den Bausatz 1 mit dem Schutzleitersystem
! Montageanleitung Erdungsbausatz für HM…63… (HMVS-DL63).
Hinweis
•Befestigen Sie eine Mittenstütze 3 mindestens alle 500 mm.
•Befestigen Sie einen Bausatz 1 mindestens alle 1000 mm.
Berechnen Sie die dazu benötigte Anzahl y nach folgenden Formeln:
– bei Hub ≤ 1000 mm: y = 2
– bei Hub > 1000 mm: y = Ganzzahl (Hub/1000) +2
•Montieren Sie die Antriebe 2 immer zuerst an den Bausatz 1.
•Verwenden Sie nur zulässige Energieführungsketten 3 laut Katalog
www.festo.com/catalogue.
•Beachten Sie, dass nur Befestigungskombinationen aus der Tabelle
zulässig sind.
•Halten Sie die zulässigen Anziehdrehmomente ein (! Tabelle).
Info
•Beachten Sie die Montagereihenfolge
! Montageübersicht für HM…63… (HMVS-DL63).
Der Bausatz 1 enthält alle maximal erforderlichen
Befestigungselemente.
•Beachten Sie, dass bei einigen Kombinationen Befestigungselemente
übrig bleiben.
2. Montage an Antriebseinheit 2
2
2
22
•Wählen Sie die Befestigungselemente (Schrauben, usw.) für Ihre
Kombination (! Tabelle).
•Beachten Sie die Bildzuordnung für Ihre Kombination (! Tabelle).
Bild 1
13916d_3
2 Linearantrieb
DGE-63-…-ZR-KF
3 Mittenstütze
MUP-63
•Befestigen Sie eine
Mittenstütze 3 mindestens
alle 500 mm.
Bild 2
13916d_4
1 Installationsbausatz
HMIXB-RP/FP-2
2 Linearantrieb
DGE-63-…-ZR-KF
•Befestigen Sie einen
Bausatz 1 mindestens
alle 1000 mm.
1)
2
1) Toleranzen für nicht tolerierte Anziehdrehmomente MA
MA > 1 Nm: ± 20%
2) wahlweise
3. Montage an Anbaukomponente 3
3
3
33
•Wählen Sie die Befestigungselemente (Schrauben, usw.) für Ihre
Kombination (! Tabelle).
•Beachten Sie die Bildzuordnung für Ihre Kombination (! Tabelle).
Bild 3
Bild 3a
13916d_5
1 Installationsbausatz
HMIXB-RP/FP-2
2 Linearantrieb
DGE-63-…-ZR-KF
3 Auflageprofil
HMIA-E05/-E072)
Bild 3b
13916d_5
1 Installationsbausatz
HMIXB-RP/FP-2
2 Linearantrieb
DGE-63-…-ZR-KF
3 Auflageprofil
HMIA-E10
Raumportal
3289d_5
1
1
2
3
B
2
HMIXB-RP/FP-2
DGE-...-ZR-KF DGE-...-ZR-KF
63 63
MUP-63 HMIA-E05/-E07
2)
HMIA-E10
1 2 3a 3b
M
A1)
[Nm]
M5x10 6 2x 4x
M8x16 24 4x
B5,3 2x 4x
MUP- 32/40 1x 2x
NST-HMV-8-2-M8 2x
M8x18 24 4x
NST-HMV-8-2-M8 2x
1 Bausatz
DGE-...-ZR-KF
HMIXB-RP/FP-2
Bild
D Zylinderschraube nach DIN 912
63
Befestigungselemente im Lieferumfang der Anbaukomponenten
A Zylinderschraube nach DIN 912
B Scheibe nach DIN 125
E Nutenstein
2 Antriebseinheit
3 Anbaukomponente
C Nutenstein
2
E
3
A
B
C
1
C
3
1
A
A
2
C
D
3
1
2
Assembly instructions (en)
744 386 / 2009-09NH
†‡
Installation kit
HMIXB-RP/FP-2
Festo SE & Co. KG
Postfach
D-73726 Esslingen
++49/(0)711/347-0
www.festo.com
1. Installation kit
1a. HMIXB-RP/FP-2
13916d_2
1 Installation kit
HMIXB-RP/FP-2
1b. Assembly example
13916d_1..Raumportal
2 Drive unit
(!Table)
3 Attachment component
(!Table)
The installation kit HMIXB-RP/FP-2 1 is intended for use as a basis for the
setup of 3D gantry systems in duo design (X modules).
Caution
Danger of injury due to electric voltage.
•Connect the kit 1 with the protective conductor system
! Assembly instructions earthing kit for HM…63… (HMVS-DL63).
Note
•Attach a central support 3 at least every 500 mm.
•Attach a basic kit 1 at least every 1000 mm.
Calculate the required quantity y using the following formulas:
– where stroke length ≤ 1000 mm: y = 2
– where stroke length > 1000 mm: y = whole-number (stroke/1000) +2
•Always mount the drives 2 to the mounting kit 1 first.
•Use only permitted energy chains 3 as specified in the catalogue
www.festo.com/catalogue.
•Note that only the fastening combinations shown in the table are
permissible.
•Maintain the permitted tightening torques (!Table).
Information
•Follow the mounting sequence
! Mounting overview for HM…63… (HMVS-DL63).
The kit 1 includes all maximally required mounting attachments.
•Note that mounting components may be left over with some
combinations.
2. Mounting on drive unit 2
2
2
22
•Select the mounting components (screws etc. ) for your combination
(! Table).
•Observe the reference to the figures for your combination (! Table).
Fig. 1
13916d_3
2 Linear drive
DGE-63-…-ZR-KF
3 Central support
MUP-63
•Attach a central support 3 at
least every 500 mm.
Fig. 2
13916d_4
1 Installation kit
HMIXB-RP/FP-2
2 Linear drive
DGE-63-…-ZR-KF
•Attach an installation kit 1
at least every 1000 mm.
1)
2
1 ) Tolerance for non-toleranced tightening torques M A
MA > 1 Nm: ± 20%
2 ) either
3. Mounting on attachment component 3
3
3
33
•Select the mounting components (screws etc. ) for your combination
(!Table).
•Observe the reference to the figures for your combination (!Table).
Fig. 3
Fig. 3a
13916d_5
1 Installation kit
HMIXB-RP/FP-2
2 Linear drive
DGE-63-…-ZR-KF
3 Support profile
HMIA-E05/-E072)
Fig. 3b
13916d_5
1 Installation kit
HMIXB-RP/FP-2
2 Linear drive
DGE-63-…-ZR-KF
3 Support profile
HMIA-E10
3D gantry
3289d_5
1
1
2
3
B
2
HMIXB-RP/FP-2
DGE-...-ZR -KF DGE-...-ZR -KF
63 63
MUP-63 HMIA-E05/-E07 2) HMIA-E10
1 2 3a 3b
MA
1) [Nm ]
M 5x1 0 6 2x 4x
M 8x1 6 24 4x
B5,3 2x 4x
M UP- 3 2/40 1x 2x
NST-HM V-8-2-M8 2x
M 8x1 8 24 4x
NST-HM V-8-2-M8 2x
E Slot nut
2 Drive unit
3 Attachment component
C Slot nut
1 Kit
DGE-...-ZR -KF
HMIXB-RP/FP-2
Fig.
D Socke t head screw as per DIN 912
63
M ounting components included with attachm ent components
A Socket head scre w as per DIN 912
B Washe r as per DIN 12 5
2
E
3
A
B
C
1
C
3
1
A
A
2
C
D
3
1
2


Produktspezifikationen

Marke: Festo
Kategorie: Nicht kategorisiert
Modell: HMIXB-RP/FP-2

Brauchst du Hilfe?

Wenn Sie Hilfe mit Festo HMIXB-RP/FP-2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Festo

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-